Development of a regenerable system employing silica-titania composites for the recovery of mercury from end-box exhaust at a chlor-alkali facility

The release of mercury to the environment is of particular concern because of its volatility, persistence, and tendency to bioaccumulate. The recovery of mercury from end-box exhaust at chlor-alkali facilities is important to prevent release into the environment and reduce emissions as required by NESHAP (National Emission Standards for Hazardous Air Pollutants). A pilot-scale photocatalytic reactor packed with silica-titania composite (STC) pellets was tested at a chloralkali facility over a 3-month period. This pilot reactor treated up to 10 ft3/min (ACFM) of end-box exhaust and achieved 95% removal. The pilot reactor was able to maintain excellent removal efficiency even with large fluctuations in influent mercury concentration (400-1600 microg/ft3). The STC pellets were regenerated ex situ by regeneration with hydrochloric acid and performed similarly to virgin STC pellets when returned to service. On the basis of these promising results, two full-scale reactors with in situ regeneration capabilities were installed and operated. After optimization, these reactors performed similarly to the pilot reactor. A cost analysis was performed comparing the treatment costs (i.e., cost per pound of mercury removed) for sulfur-impregnated activated carbon and the STC system. The STC proved to be both technologically and economically feasible for this installation.     

Phosphorus removal from municipal wastewater by hydrous ferric oxide reactive filtration and coupled chemically enhanced secondary treatment: part I--performance.

This work examines the performance of a hydrous ferric oxide (HFO) reactive filtration (RF) process with coupled chemically enhanced secondary treatment (RECYCLE) for phosphorus removal from municipal wastewater (HFO-RF-RECYCLE). A 3-month, 0.95-ML/d (0.25-mgd) demonstration of HFO-RF-RECYCLE was performed at a municipal wastewater treatment plant equipped with oxidation ditches and secondary clarifiers. Influent to the plant averaged 6.0 mg/L phosphorus, with a tertiary effluent average of 0.011 mg/L phosphorus. Iron doses to the plant were low, at 5 mg/L. Inline recycling of HFO solution rejects to the plant influent resulted in a maximum 90.3%, dose-dependent reduction of phosphorus in the secondary effluent at 4.5 ML/d (1.2 mgd). Other results included reduction of total suspended solids and turbidity. A mass balance analysis was performed. We conclude that HFO-RF-RECYCLE may allow very low levels of phosphorus discharge from municipal wastewater treatment plants with a ferric-iron-based tertiary filtration process and residual recycling.     

Persistent organic pollutants in atmospheric deposition and biomonitoring with Tillandsia usneoides (L.) in an industrialized area in Rio de Janeiro state, southeast Brazil--Part II: PCB and PAH

Monitoring of immission of persistent organic pollutants in the industrialized area of Volta Redonda (V.R.) and in the National Park of Itatiaia (PNI) in southeast Brazil was performed using an endemic bromeliad species as biomonitor and measuring bulk deposition rates of polychlorinated biphenyls (PCB) and polycyclic aromatic hydrocarbons (PAH). For the sum of PCB, overall deposition rates were between 17 and 314 ng/(m2 day) in winter and between 43 and 81 ng/(m2 day) in summer, respectively. Deposition rates of dioxin-like PCBs ranged from 0.14 to 2.8 pg WHO-TEQ/(m2 day) in winter and from 0.90 to 4.3 pg WHO-TEQ/(m2 day) in summer. PCB deposition rates (total PCB and WHO-TEQ) were in the same range in winter in V.R. and PNI. In summer, contamination levels in V.R. were 6-10-folds higher than in PNI. PCB concentrations in biomonitor samples from V.R. and PNI were in the same range in summer and in winter. Concentrations of total PCB ranged from 14 to 95 microg/kg dry matter (d.m.) in winter and from 18 to 27 microg/kg d.m. in summer, respectively. The TEQ values were between 1.7 and 4.1 ng WHO-TEQ/kg d.m. in winter and between 1.9 and 2.9 ng WHO-TEQ/kg d.m. in summer. PCB concentrations of di-ortho PCB but not of non-ortho PCB were a factor of 2-4 lower in summer in both areas. PCB congener profiles resembled those from technical formulations. The profiles shifted to the higher chlorinated congeners in summer, probable due to revolatilisation of the lighter components at higher temperatures. PCB profiles in biomonitor resembled those from deposition samples and the shift to the heavier congeners in summer was even more pronounced. PAH deposition rates were in a similar range in both areas (131-2415 ng/(m2 day)). PAH levels in biomonitor samples from V.R. were about one order of magnitude higher than in samples from PNI indicating the impact of local sources. PAH profiles revealed stationary thermal processes as main source of contamination in V.R. whereas in PNI, biomass burning seems to be the main contamination source.     

Preliminary evidence of a decline in perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) concentrations in American Red Cross blood donors

The purpose of this pilot study was to determine whether perfluorooctanesulfonate (PFOS,C(8)F(17)SO(3)(-)) and perfluorooctanoate (PFOA,C(7)F(15)CO(2)(-)) concentrations in American Red Cross blood donors from Minneapolis-St. Paul, Minnesota have declined after the 2000-2002 phase-out of perfluorooctanesulfonyl-fluoride (POSF, C(8)F(17)SO(2)F)-based materials by the primary global manufacturer, 3M Company. Forty donor plasma samples, categorized by age and sex, were collected in 2005, and PFOS and PFOA concentrations were compared to 100 (non-paired) donor serum samples collected in 2000 from the same general population that were analyzed at the time using ion-pair extraction methods with tetrahydroperfluorooctanesulfonate as an internal standard. Eleven of the 100 samples originally collected were reanalyzed with present study methods that involved (13)C- labeled PFOA spiked into the donor samples, original samples, control human plasma, and the calibration curve prior to extraction, and was used as a surrogate to monitor extraction efficiency. Quantification was performed by high performance liquid chromatography tandem mass spectrometry methods. Among the 100 serum samples analyzed for PFOS, the geometric mean was 33.1 ng ml(-1) (95% CI 29.8-36.7) in 2000 compared to 15.1 ng ml(-1) (95% CI 13.3-17.1) in 2005 (p<0.0001) for the 40 donor plasma samples. The geometric mean concentration for PFOA was 4.5 ng ml(-1) (95% CI 4.1-5.0) in 2000 compared to 2.2 ng ml(-1) (95% CI 1.9-2.6) in 2005 (p<0.0001). The decrease was consistent across donors' age and sex. To confirm these preliminary findings, additional sub-sets of year 2000 samples will be analyzed, and a much larger biomonitoring study of other locations is planned.     

Modeling in-situ uranium(VI) bioreduction by sulfate-reducing bacteria

We present a travel-time based reactive transport model to simulate an in-situ bioremediation experiment for demonstrating enhanced bioreduction of uranium(VI). The model considers aquatic equilibrium chemistry of uranium and other groundwater constituents, uranium sorption and precipitation, and the microbial reduction of nitrate, sulfate and U(VI). Kinetic sorption/desorption of U(VI) is characterized by mass transfer between stagnant micro-pores and mobile flow zones. The model describes the succession of terminal electron accepting processes and the growth and decay of sulfate-reducing bacteria, concurrent with the enzymatic reduction of aqueous U(VI) species. The effective U(VI) reduction rate and sorption site distributions are determined by fitting the model simulation to an in-situ experiment at Oak Ridge, TN. Results show that (1) the presence of nitrate inhibits U(VI) reduction at the site; (2) the fitted effective rate of in-situ U(VI) reduction is much smaller than the values reported for laboratory experiments; (3) U(VI) sorption/desorption, which affects U(VI) bioavailability at the site, is strongly controlled by kinetics; (4) both pH and bicarbonate concentration significantly influence the sorption/desorption of U(VI), which therefore cannot be characterized by empirical isotherms; and (5) calcium-uranyl-carbonate complexes significantly influence the model performance of U(VI) reduction.     

Well water contaminated by acidic mine water from the Dabaoshan Mine, south China: chemistry and toxicity

An investigation into well water quality was carried out in a rural area subject to irrigation with acidic mine water from the Guangdong Dabaoshan Mine, southern China. The results of water pH measurements from 112 wells in two different seasons suggest that the well water has been contaminated to varying degrees in the investigated Shangba floodplain (approximately 11km south of the Guangdong Dabaoshan Mine). There is a trend that well water pH increased southwards, suggesting that the impacts of acidic irrigation water on groundwater decreased with increasing distance to the entry point of acidic irrigation water. Water quality monitoring results of the selected wells show that Cu and Cd in the water exceeded the limits set in the Chinese National Standards for Drinking Water (GB 5749-85) for the wells close to the irrigation water source. If the World Health Organization (WHO) standard was considered, Cd in some wells was almost 10 times as high as the WHO guideline value (0.003mg l(-1)). Water collected from the location closest to the acidic irrigation water source was acutely toxic to the test organism (Daphnia carinata) even after 51 time dilution. It is likely that the extremely high mortality rate of the local population reported for the study area is at least partly related to the high levels of heavy metals, particularly Cd in the drinking well water.     

Spatial and temporal variations and possible sources of dichlorodiphenyltrichloroethane (DDT) and its metabolites in rivers in Tianjin, China

Water, suspended solid (SS) and sediment samples were collected from nine water courses in Tianjin, China and analyzed for dichlorodiphenyltrichloroethane (DDT) and its metabolites (DDXs, including o,p'-,p,p'-DDT, DDD and DDE). The average DDX concentrations in water, SS and sediment were 59+/-30 ng l(-1), 2690+/-1940 ng g(-1)dry wt. and 340+/-930 ng g(-1)dry wt., respectively. Due to the termination of the extensive agricultural application and industrial manufacture, DDXs in river sediment decreased by one order of magnitude since 1970's and low DDT fractions in these sediments were observed. Still, DDXs in the sediments near the outlets of the major manufacturers remained relatively high attributed to the historic input. DDXs in sediment were also positively correlated with organic matter content. Spatial distributions of DDXs in SS and water was different from that in sediment. For SS, a negative correlation between DDX concentration and SS content indicated a dilution effect in many rivers. Dissolved organic carbon content was the major factor affecting DDX concentrations in water phase. Wastewater discharged from dicofol manufacturers and likely illegal agricultural application were the primary reasons causing high DDT (DDE+DDD) ratios in SS and water.     

Transport of simazine in unsaturated sandy soil and predictions of its leaching under hypothetical field conditions

The potential contamination of groundwater by herbicides is often controlled by processes in the vadose zone, through which herbicides travel before entering groundwater. In the vadose zone, both physical and chemical processes affect the fate and transport of herbicides, therefore it is important to represent these processes by mathematical models to predict contaminant movement. To simulate the movement of simazine, a herbicide commonly used in Chilean vineyards, batch and miscible displacement column experiments were performed on a disturbed sandy soil to quantify the primary parameters and processes of simazine transport. Chloride (Cl(-)) was used as a non-reactive tracer, and simazine as the reactive tracer. The Hydrus-1D model was used to estimate the parameters by inversion from the breakthrough curves of the columns and to evaluate the potential groundwater contamination in a sandy soil from the Casablanca Valley, Chile. The two-site, chemical non-equilibrium model was observed to best represent the experimental results of the miscible displacement experiments in laboratory soil columns. Predictions of transport under hypothetical field conditions using the same soil from the column experiments were made for 40 years by applying herbicide during the first 20 years, and then halting the application and considering different rates of groundwater recharge. For recharge rates smaller than 84 mm year(-1), the predicted concentration of simazine at a depth of 1 m is below the U.S. EPA's maximum contaminant levels (4 microg L(-1)). After eight years of application at a groundwater recharge rate of 180 mm year(-1) (approximately 50% of the annual rainfall), simazine was found to reach the groundwater (located at 1 m depth) at a higher concentration (more than 40 microg L(-1)) than the existing guidelines in the USA and Europe.     

Laboratory and field evaluation of crystallized DOW 704 oil on the performance of the Well Impactor Ninety-Six fFine particulate matter fractionator

Subsequent to the 1997 promulgation of the Federal Reference Method (FRM) for monitoring fine particulate matter (PM2.5) in ambient air, U.S. Environmental Protection Agency (EPA) received reports that the DOW 704 diffusion oil used in the method's Well Impactor Ninety-Six (WINS) fractionator would occasionally crystallize during field use, particularly under wintertime conditions. Although the frequency of occurrence on a nationwide basis was low, uncertainties existed as to whether crystallization of the DOW 704 oil may adversely affect a sampling event's data quality. In response to these concerns, EPA and the State of Connecticut Department of Environmental Protection jointly conducted a series of specialized tests to determine whether crystallized oil adversely affected the performance of the WINS fractionator. In the laboratory, an experimental setup used dry ice to artificially induce crystallization of the diffusion oil under controlled conditions. Using primary polystyrene latex calibration aerosols, standard size-selective performance tests of the WINS fractionator showed that neither the position nor the shape of the WINS particle size fractionation curve was substantially influenced by the crystallization of the DOW 704 oil. No large particle bounce from the crystallized impaction surface was observed. During wintertime field tests, crystallization of the DOW 704 oil did not adversely affect measured PM2.5 concentrations. Regression of measurements with crystallized DOW 704 versus liquid dioctyl sebacate (DOS) oil produced slope, intercept, and R2 values of 0.98, 0.1, and 0.997 microg/m3, respectively. Additional field tests validated the use of DOS as an effective impaction substrate. As a result of these laboratory and field tests, DOS oil has been approved by EPA as a substitute for DOW 704 oil. Since the field deployment of DOS oil in 2001, users of this alternative oil have not reported any operational problems associated with its use in the PM2.5 FRM. Limited field evaluation of the BGI very sharp cut cyclone indicates that it provides a viable alternative to the WINS fractionator.     

Loading effect correction for real-time aethalometer measurements of fresh diesel soot

In this study, a correction was developed for the aethalometer to measure real-time black carbon (BC) concentrations in an environment dominated by fresh diesel soot. The relationship between the actual mass-specific absorption coefficient for BC and the BC-dependent attenuation coefficients was determined from experiments conducted in a diesel exposure chamber that provided constant concentrations of fine particulate matter (PM; PM(2.5); PM < 2.5 microm in aerodynamic diameter) from diesel exhaust. The aethalometer reported BC concentrations decreasing with time from 48.1 to 31.5 microg m(-3) when exposed to constant PM(2.5) concentrations of 55 +/- 1 microg m(-3) and b(scat) = 95 +/- 3 Mm(-1) from diesel exhaust. This apparent decrease in reported light-absorbing PM concentration was used to derive a correction K(ATN) for loading of strong light-absorbing particles onto or into the aethalometer filter tape, which was a function of attenuation of light at 880 nm by the embedded particles.