Removal of PCB-DNAPL from a rough-walled fracture using alcohol/polymer flooding

Phase behaviour experiments employing PCB (Aroclor 1242)/alcohol/water systems were conducted with ethanol (EtOH) and n-propanol (nPA). Both exhibited an affinity for the aqueous phase within the entire two-phase region. As much as 88% by volume (88% vol.) EtOH and 80% vol. nPA were necessary to achieve full miscibility of the PCB in the aqueous phase. DNAPL-water interfacial tension (IFT) was reduced from 38.9 dyn/cm to 4.7 dyn/cm and 2.4 dyn/cm with 80% vol. EtOH and 76% vol. nPA. The addition of alcohol brought about 41% and 54% reductions in DNAPL viscosity at maximal concentrations of EtOH and nPA. Density of the PCB-DNAPL was relatively unaffected by the presence of alcohol. A series of seven experiments were conducted where successive slugs of nPA and xanthan gum polymer solutions were injected into a fractured shale sample. A 30% vol. nPA solution injected under a hydraulic gradient of 0.36 allowed enhanced PCB removal primarily through reduction of IFT and resulted in 72% DNAPL recovery. Several pore volumes of alcohol solution were necessary to displace all the potentially mobile non-wetting phase since the high-viscosity DNAPL was mobilized at a lower flow rate than the overall fluid velocity, illustrating non-piston displacement. The injection of a 95% vol. nPA alcohol solution, theoretically at a sufficient concentration to produce fully miscible displacement of the residual DNAPL at equilibrium, resulted in non-equilibrium partitioning of the PCB into the flushing solution, likely due to the high fluid velocities in the fracture. The injection of 200 pore volumes of 95% vol. nPA solution resulted in 94% DNAPL recovery. Alcohol floods operated below the miscibility envelope appear to be a valuable source zone remedial alternative where the objective is to reduce DNAPL mobility to zero, but it should be noted that DNAPL mobility is increased during the application of the technology and steps may need to be taken to prevent unwanted vertical mobilization.     

Remediation of contaminated agricultural soils near a former Pb/Zn smelter in Austria: batch, pot and field experiments

Metal contaminated crops from contaminated soils are possible hazards for the food chain. The aim of this study was to find practical and cost-effective measures to reduce metal uptake in crops grown on metal contaminated soils near a former metal smelter in Austria. Metal-inefficient cultivars of crop plants commonly grown in the area were investigated in combination with in-situ soil amendments. A laboratory batch experiment using 15 potential amendments was used to select 5 amendments to treat contaminated soil in a pot study using two Barley (Hordeum vulgare L.) cultivars that differed in their ability to accumulate cadmium. Results from this experiment identified 3 of these amendments for use in a field trial. In the pot experiment a reduction in ammonium nitrate extractable Cd (<41%) and Pb (<49%) compared to the controls was measured, with a concurrent reduction of uptake into barley grain (Cd<62%, Pb<68%). In the field extractable fractions of Cd, Pb, and Zn were reduced by up to 96%, 99%, and 99%, respectively in amended soils.     

In situ and laboratory bioassays using Poecilia reticulata Peters, 1859 in the biomonitoring of an acidic lake at Camaçari, BA, Brazil

The suitability and viability of acute in situ bioassays were investigated in the biomonitoring program of an acidic lake contaminated with sulphur residues. Responses of organisms observed in laboratory and in situ bioassays were also assessed to determine whether or not they were similar and comparable, regarding accuracy and precision. Newborn Poecilia reticulata were employed as test organisms and exposed to the same water samples under in situ and laboratory conditions. Mortality/immobility was the endpoint assessed and dead/immobile organisms were counted at various time intervals during exposure. The mean calculated LT50 values and 95% confidence intervals were 1.61 (1.36-1.87) h in the laboratory bioassays and 0.72 (0.55-0.89) h in the in situ bioassays. Statistical comparison of these values revealed a significant difference (p<0.05). In situ bioassays were more accurate than those carried out in the laboratory, demonstrating higher sensitivity and better reproduction of what occurs in nature, while laboratory bioassays were more precise.     

Evaluation of ozone-nitrogen oxides-volatile organic compound sensitivity of Cincinnati, Ohio

Ambient concentrations of ozone (O3), nitrogen oxides (NOx), total reactive nitrogen (NOy), nitric acid (HNO3), and hydrogen peroxide (H2O2) were measured during September 2003 at an urban site of Cincinnati, OH. The aim of this study was two-fold: to investigate whether O3 formation in this population exposure-type site is NOx, sensitive or volatile organic compound (VOC) sensitive and to test the practicality of using two combined observational-based methods to identify the sensitivity of O3 formation in midlevel polluted locations. The evaluation of the indicator species: NOy, O3/NOy, O3/HNO3, H2O2/ HNO3, and O3/(estimated NOx reaction products), as well as the combined hypothesis testing analysis of the weekend/weekday (WE/WD) differences of 1-hr and 8-hr average maximum O3 and of the 6:00 a.m.-9:00 a.m. average nitric oxide and NOx concentrations, show evidence that Cincinnati is likely VOC sensitive. Average WE 1-hr and 8-hr maximum O3, as well as duration of WE O3 accumulation, were not lower than the corresponding WD levels in spite of the observed significant reduction in NO, emissions on WE, a typical situation in VOC-sensitive locations. The possibility that the seasonal transition from summer to autumn could have influenced the results was also investigated through an exploratory analysis of the afternoon O3 maximum/NOx measured and of the WE/WD differences of peak O3 and morning average NO and NO, concentrations observed at this site from June through September 2003. The results suggest that a VOC-sensitive chemistry regime dominated along the summer season. The findings of this study suggest that additional reductions in regional NO, emissions in Cincinnati, a potential nonattainment area under the 8-hr O3 standard, may cause an increase in local O3. Future strategies to reduce O3 in Southwest Ohio should be further evaluated carefully. The combination of observational-based methods might provide a consistent complementary approach in the identification of the NO,-VOC sensitive characteristics of mid-to-moderate polluted urban areas.     

Phytostabilization of a metal contaminated sandy soil. I: Influence of compost and/or inorganic metal immobilizing soil amendments on phytotoxicity and plant availability of metals

In a lysimeter set-up, compost addition to an industrial contaminated soil slightly reduced phytotoxicity to bean seedlings. The "Phytotoxicity Index" (on a scale from 1 to 4) decreased from 3.5 to 2.8. The same treatment also reduced metal accumulation in grasses: mean Zn, Cd and Pb concentrations decreased respectively from 623 to 135, from 6.2 to 1.3 and from 10.7 to <6 mg kg-1 dry weight. When combined with inorganic metal immobilizing amendments, compost had a beneficial effect on plant responses additional to the inorganic amendments alone. Best results were obtained when using compost (C)+cyclonic ashes (CA)+steel shots (SS). The "Phytotoxicity Index" decreased to 1.7, highest diversity of spontaneously colonizing plants occurred, and metal accumulation in grasses reduced to values for uncontaminated soils. Based on the first year evaluation, C+CA+SS showed to be an efficient treatment for amendment assisted phytostabilization of the contaminated Overpelt soil.     

Genotypic variations in the accumulation of Cd, Cu, Pb and Zn exhibited by six commonly grown vegetables

Metal contaminants in garden and allotment soils could possibly affect human health through a variety of pathways. This study focused on the potential pathway of consumption of vegetables grown on contaminated soil. Five cultivars each of six common vegetables were grown in a control and in a soil spiked with Cd, Cu, Pb and Zn. Highly significant differences in metal content were evident between cultivars of a number of vegetables for several of the contaminants. Carrot and pea cultivars exhibited significant differences in accumulated concentrations of Cd and Cu with carrot cultivars also exhibiting significant differences in Zn. Distinctive differences were also identified when comparing one vegetable to another, legumes (Leguminosae) tending to be low accumulators, root vegetables (Umbelliferae and Liliaceae) tending to be moderate accumulators and leafy vegetables (Compositae and Chenopodiaceae) being high accumulators.     

Changes in amino acid profile and metal content in seeds of Cicer arietinum L. (chickpea) grown under various fly-ash amendments

Seeds of Cicer arietinum L. plants are edible and a valuable source of protein. Accumulation of toxic metals in the edible part of the plant, grown in fields close to fly-ash (FA) landfills, may pose a threat to human health. In the present study, the effects of FA and its amendments with different ameliorants viz., garden soil (GS), press mud (PM) and saw dust (SD), on total soluble protein contents, amino acid composition and metal accumulation in seeds were investigated in var. CSG-8962 and var. C-235 of C. arietinum. Plants accumulated adequate amounts of essential metals viz. Fe, Cu, Zn in seeds, while the toxic metals such as Cd and Cr were taken up in smaller quantities. The accumulation of Cr and Cd was less in var. C-235 than var. CSG-8962. Amendment of FA with PM enhanced the amount of soluble protein and amino acids in both varieties and was found to be superior among all tested ameliorants. Both quantitative and qualitative analysis of amino acids showed better response in var. C-235 as compared to var. CSG-8962. Thus var. C-235 seems to be suitable for cultivation in FA contaminated areas due to more accumulation of essential metals and less accumulation of toxic metals in seeds. Application of PM may further improve the growth of plants and nutritional quality of seeds.     

Effect of farmyard manure application on boron adsorption-desorption characteristics of some soils

Boron (B) availability to crop plants depends on soil properties as well as management practices like liming, fertilization and use of organic manures. To assess the effect of farmyard manure (FYM) application on availability of added B, adsorption-desorption of B was investigated in five different soils receiving varying doses of FYM (0, 5 and 10 g FYM kg(-1) soil). Two surfaces Freundlich model was found best to account for B adsorption-desorption data of all soils. Application of FYM increased B adsorption capacities pertaining to low (K1) and high (K2) concentration ranges in all soils, except Soil C (Alfisol) having a pH of 9.8, in which the higher rate of FYM decreased the value of K2. Application of FYM did not change B desorption capacities of soils corresponding to low B concentration range (K(1)(1)) significantly, however, it increased B desorption capacity pertaining to high B concentration (K(1)(2)) in all soils, except Soils C (Alfisol) and E (Entisol) having pH of 9.8 and 5.1, respectively. Application of FYM increased the desorption slope factor applicable to low concentration range (1/n(1)(1)) in Soil A (Inceptisol), but decreased it in Soil E (Entisol). The 1/n(1)(2) (desorption slope factor applicable to high concentration range) decreased with FYM application in all soils except Soil E (Entisol), where it was increased. Boron desorption index (slope(ads)/slope(des)) decreased with FYM application in low B concentration range, but increased in high concentration range for all soils except soil E (Entisol, pH 5.1), in which a reverse trend was observed. Application of FYM increased the retention of added B in soils and may help reducing the leaching losses.     

Pyrolysis behavior of tire-derived fuels at different temperatures and heating rates

Pyrolytic product distribution rates and pyrolysis behavior of tire-derived fuels (TDF) were investigated using thermogravimetric analyzer (TGA) techniques. A TGA was designed and built to investigate the behavior and products of pyrolysis of typical TDF specimens. The fundamental knowledge of TGA analysis and principal fuel analysis are applied in this study. Thermogravimetry of the degradation temperature of the TDF confirms the overall decomposition rate of the volatile products during the depolymerization reaction. The principal fuel analysis (proximate and ultimate analysis) of the pyrolytic char products show the correlation of volatilization into the gas and liquid phases and the existence of fixed carbon and other compounds that remain as a solid char. The kinetic parameters were calculated using least square with minimizing sum of error square technique. The results show that the average kinetic parameters of TDF are the activation energy, E = 1322 +/- 244 kJ/mol, a pre-exponential constant of A = 2.06 +/- 3.47 x 10(10) min(-1), and a reaction order n = 1.62 +/- 0.31. The model-predicted rate equations agree with the experimental data. The overall TDF weight conversion represents the carbon weight conversion in the sample.     

Effects of initial saturation on properties modification and displacement of tetrachloroethene with aqueous isobutanol

Packed column experiments were conducted to study effects of initial saturation of tetrachloroethene (PCE) in the range of 1.0-14% pore volume (PV) on mobilization and downward migration of the non-aqueous phase liquid (NAPL) product upon contact with aqueous isobutanol ( approximately 10 vol.%). This study focused on the consequences of swelling beyond residual saturation. Columns were packed with mixtures of neat PCE, water and glass beads and waterflooded to establish a desired homogeneous residual saturation, and then flooded with aqueous isobutanol under controlled hydraulic conditions. Results showed a critical saturation of approximately 8% PV for these packed column experimental conditions. At low initial PCE saturations (<8% PV), experimental results showed reduced risk of NAPL-product migration upon contact with aqueous isobutanol. At higher initial PCE saturations (>8% PV), results showed NAPL-product mobilization and downward migration which was attributed to interfacial tension (IFT) reduction, swelling of the NAPL-product, and reduced density modification. Packed column results were compared with good agreement to theoretical predictions of NAPL-product mobilization using the total trapping number, N(T). In addition to the packed column study, preliminary batch experiments were conducted to study the effects of PCE volumetric fraction in the range of 0.5-20% on density, viscosity, and IFT modification as a function of time following contact with aqueous isobutanol ( approximately 10 vol.%). Modified NAPL-product fluid properties approached equilibrium within approximately 2 h of contact for density and viscosity. IFT reduction occurred immediately as expected. Measured fluid properties were compared with good agreement to theoretical equilibrium predictions based on UNIQUAC. Overall, this study demonstrates the importance of initial DNAPL saturation, and the associated risk of downward NAPL-product migration, in applying alcohol flooding for remediation of DNAPL contaminated ground water sites.