Performance,combustion and emission characteristics of a single-cylinder,four-stroke,direct injection diesel engine operated on a dual-fuel mode using Honge oil methyl ester and producer gas derived from biomass feedstock of different origin

Renewable and alternative fuels have numerous advantages compared with fossil fuels, as they are renewable and biodegradable, and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues. In this context, present work was carried out to investigate the feasibility of alternative and renewable fuels derived from biomass feedstock of different origin for engine applications. The present study was also extended to study the effect of producer gas composition derived from different biomass feedstock on the performance, combustion and emission characteristics of a single-cylinder, four-stroke, direct injection stationary diesel engine operated on a dual-fuel mode using Honge oil methyl ester (HOME) and producer gas induction. The performance of the engine was evaluated with a constant injection timing of 27° before top dead centre, an injection pressure of 205 bar for the diesel–producer gas combination and 230 bar for the HOME–producer gas combination and a compression ratio of 17.5. The results showed that the performance of the dual-fuel engine varies with the composition of the producer gas and depends on the type of biomass feedstock used in the gasifier. Experimental investigations on the dual-fuel engine showed that brake thermal efficiency values for the engine operated using HOME–producer gas derived from babul, neem and honge woods were found to be 17.2, 14.3 and 11.56% respectively, compared to 23.8% for diesel–producer gas operation at 80% load. However, the results showed better engine performance with lower exhaust emission levels for the operation of HOME–producer gas derived from the ordinary or babul wood compared with the operation of that derived from the neem and Honge woods. In view of this, present study reveals that use of alternative and renewable fuels for dual fuel engine can be considered as an immediate solution for the development of rural areas and emergency use in the event of severe diesel fuel shortage.     

Effects of compression ratio,swirl augmentation techniques and ethanol addition on the combustion of CNG–biodiesel in a dual-fuel engine

The diminishing resources and continuously increasing cost of petroleum in association with their alarming pollution levels from diesel engines has led to an interest in finding alternative fuels to diesel. Emission control and engine efficiency are two of the most important parameters in current engine design. The impending introduction of emission standards such as Euro IV and Euro V has forced research towards developing new technologies for combating engine emissions. This paper examines the effects of compression ratio, swirl augmentation techniques and ethanol addition on the combustion of compressed natural gas (CNG) blended with Honge oil methyl esters (HOME) in a dual fuel engine. The present results show that the combustion of HOME and 15% ethanol blend with CNG induction in a dual-fuel engine operated in optimized parameters at an injection timing of 27° Before Top Dead Centre and a compression ratio of 17.5 resulted in acceptable combustion emissions and improved brake thermal efficiencies. The implementation of swirl augmentation techniques increased brake thermal efficiencies (BTEs) and considerably reduced combustion emissions such as smoke, HC, CO and NO_x. The addition of ethanol also increased BTEs. However, at more than 15% of ethanol in HOME, NO_x emissions increased dramatically.     

Adaptation options for marine industries and coastal communities using community structure and dynamics

Identifying effective adaptation strategies for coastal communities dependent on marine resources and impacted by climate change can be difficult due to the dynamic nature of marine ecosystems. The task is more difficult if current and predicted shifts in social and economic trends are considered. Information about social and economic change is often limited to qualitative data. A combination of qualitative and quantitative models provide the flexibility to allow the assessment of current and future ecological and socio-economic risks and can provide information on alternative adaptations. Here, we demonstrate how stakeholder input, qualitative models and Bayesian belief networks (BBNs) can provide semi-quantitative predictions, including uncertainty levels, for the assessment of climate and non-climate-driven change in a case study community. Issues are identified, including the need to increase the capacity of the community to cope with change. Adaptation strategies are identified that alter positive feedback cycles contributing to a continued decline in population, local employment and retail spending. For instance, the diversification of employment opportunities and the attraction of new residents of different ages would be beneficial in preventing further population decline. Some impacts of climate change can be combated through recreational bag or size limits and monitoring of popular range-shifted species that are currently unmanaged, to reduce the potential for excessive removal. Our results also demonstrate that combining BBNs and qualitative models can assist with the effective communication of information between stakeholders and researchers. Furthermore, the combination of techniques provides a dynamic, learning-based, semi-quantitative approach for the assessment of climate and socio-economic impacts and the identification of potential adaptation strategies.     

Bages-Sigean and Canet-St Nazaire lagoons (France): physico-chemical characteristics and contaminant concentrations (Cu,Cd, PCBs and PBDEs) as environmental quality of water and sediment

Environmental characteristics in water and sediments of two contrasted coastal Mediterranean lagoons, Bages-Sigean and Canet-St Nazaire, were measured over a three season survey. The urban pollution (treatment plant discharges) is very important in Canet-St Nazaire lagoon reflecting untreated sewages, while in Bages-Sigean, the northern part appears more impacted due to larger anthropogenic inputs. Dissolved Cd concentrations are on the whole similar in both lagoons, whereas Cu concentrations are by far higher in lagoon Canet-St Nazaire. Cu concentrations appear to be highly dependent on dissolved organic carbon whereas salinity seems to control Cd variations. Concerning the sediments, the confined northern part of lagoon Bages-Sigean shows organic carbon and total nitrogen enrichment whereas lipid concentrations are much higher in the Canet-St Nazaire lagoon. Cu complexation seems to be strongly related to organic matter as evidenced by the two significant positive relationships, on one hand between Cu and organic carbon, and on the other hand, between Cu and lipids. On the contrary, Cd concentrations appear to be mainly controlled by carbonates. PCBs and PBDEs were detected only in sediments and show relatively low concentrations compared to similar lagoon environments. Regarding the sediment quality guidelines, Cd, Cu and PCBs in both lagoons did not exceed any Probable Effect Concentration (PEC).     

Solubilization of municipal sewage waste activated sludge by novel lytic bacterial strains

Extracellular polymeric substances (EPS) are an extracellular matrix found in sludge which plays a crucial role in flocculation by interacting with the organic solids. Therefore, to enhance pretreatment of sludge, EPS have to be removed. In this study, EPS were removed with a chemical extractant, NaOH, to enhance the bacterial pretreatment. A lysozyme secreting bacterial consortium was isolated from the waste activated sludge (WAS). The result of density gradient gel electrophoresis (DGGE) analysis revealed that the isolated consortium consists of two strains. The two novel strains isolated were named as Jerish03 (NCBI accession number KC597266) and Jerish 04 (NCBI accession number KC597267) and they belong to the genus Bacillus. Pretreatment with these novel strains enhances the efficiency of the aerobic digestion of sludge. Sludge treated with the lysozyme secreting bacterial consortium produced 29 % and 28.5 % increase in suspended solids (SS) reduction and chemical oxygen demand (COD) removal compared to the raw activated sludge (without pretreatment) during aerobic digestion. It is specified that these two novel strains had a high potential to enhance WAS degradation efficiency in aerobic digestion.     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.     

Nutrient and enzymatic changes of hydrolysed tannery solid waste treated with epigeic earthworm Eudrilus eugeniae and phytotoxicity assessment on selected commercial crops

Animal fleshing (ANFL) is the predominant proteinaceous solid waste generated during processing of leather and it is confronting disposal problems. The aim of this study was to assess the potential of epigeic earthworm Eudrilus eugeniae to utilize and transform the fermented ANFL in the solid state (SSF) and submerged state (SmF) into a value added product along a low residence period (25 days). A total of six treatment units containing different waste mixture compositions were established. Fifty healthy and non-clitellated earthworms were introduced in three different treatment containers: control, SSF, and SmF (+worm). Another set of treatment mixtures (control, SSF, SmF) was established without earthworms (?worm) to compare the results. The products were characterized for physico-chemical, enzymatic analysis and seedling growth parameters to compare the differences in the process with and without earthworms. The changes observed in the analytical parameters were in the following order: SSF > SmF > control mixtures (p?<?0.05). The vermicompost showed a significant reduction in heavy metals, total organic carbon and an increase in total Kjeldhal nitrogen as compared to the product untreated by earthworms. The maximum enzymatic activities were observed after 21 days of vermicomposting. The relative seed germination of vermicompost extracts were in the order of tomato (Lycopersicon esculentum) > green gram (Vigna radiata) > cucumber (Cucumis sativus) > bottle gourd (Lagenaria siceraria (Mol.) Standl.) and showed no phytotoxicity effects. The results indicated that the combination of both ANFL hydrolysis through fermentation and vermicomposting is a good alternative to the management of this kind of waste.     

Biomass smoke in Burkina Faso: what is the relationship between particulate matter,carbon monoxide,and kitchen characteristics?

In Burkina Faso where cooking with biomass is very common, little information exists regarding kitchen characteristics and their impact on air pollutant levels. The measurement of air pollutants such as respirable particulate matter (PM₁₀), an important component of biomass smoke that has been linked to adverse health outcomes, can also pose challenges in terms of cost and the type of equipment needed. Carbon monoxide could potentially be a more economical and simpler measure of air pollution. The focus of this study was to first assess the association of kitchen characteristics with measured PM₁₀ and CO levels and second, the relationship of PM₁₀ with CO concentrations, across these different kitchen characteristics in households in Nouna, Burkina Faso. Twenty-four-hour concentrations of PM₁₀ (area) were measured with portable monitors and CO (area and personal) estimated using color dosimeter tubes. Data on kitchen characteristics were collected through surveys. Most households used both wood and charcoal burned in three-stone and charcoal stoves. Mean outdoor kitchen PM₁₀ levels were relatively high (774 μg/m³, 95 % CI 329–1,218 μg/m³), but lower than indoor concentrations (Satterthwaite t value, ?6.14; p?<?0.0001). In multivariable analyses, outdoor kitchens were negatively associated with PM₁₀ (OR?=?0.06, 95 % CI 0.02–0.16, p value <0.0001) and CO (OR?=?0.03, 95 % CI 0.01–0.11, p value <0.0001) concentrations. Strong area PM₁₀ and area CO correlations were found with indoor kitchens (Spearman’s r?=?0.82, p?<?0.0001), indoor stove use (Spearman’s r?=?0.82, p?<?0.0001), and the presence of a smoker in the household (Spearman’s r?=?0.83, p?<?0.0001). Weak correlations between area PM₁₀ and personal CO levels were observed with three-stone (Spearman’s r?=?0.23, p?=?0.008) and improved stoves (Spearman’s r?=?0.34, p?=?0.003). This indicates that the extensive use of biomass fuels and multiple stove types for cooking still produce relatively high levels of exposure, even outdoors, suggesting that both fuel subsidies and stove improvement programs are likely necessary to address this problem. These findings also indicate that area CO color dosimeter tubes could be a useful measure of area PM₁₀ concentrations when levels are influenced by strong emission sources or when used in indoors. The weaker correlation observed between area PM₁₀ and personal CO levels suggests that area exposures are not as useful as proxies for personal exposures, which can vary widely from those recorded by stationary monitors.     

Marine organisms as heavy metal bioindicators in the Persian Gulf and the Gulf of Oman

In the present study, cadmium and lead concentrations were compared in barnacles, ghost shrimps, polychaetes, bivalves, and sediment from ten different locations along the intertidal zone of the Persian Gulf and the Gulf of Oman. The results revealed significant differences in the heavy metal concentrations between the organisms with barnacles showing, by far, the highest metal concentrations. The bioaccumulation factor of Cd in different animals follows this pattern with barnacles?>?bivalves?>?polychaetes?>?ghost shrimps, while the pattern for Pb was barnacles?>?polychaetes?>?bivalves?>?ghost shrimps. In most of the stations, sediments showed the lowest lead and cadmium concentrations. Therefore, it is concluded that barnacles with Pb concentrations between 0.17 and 2,016.1 μg/g and Cd concentrations ranging from 0.4 to 147.1 μg/g are the best organisms to be employed in monitoring programs designed to assess pollution with bioavailable metals in the Persian Gulf and the Gulf of Oman.     

Use of hairy roots extracts for 2,4-DCP removal and toxicity evaluation by Lactuca sativa test

2,4-Dichlorophenol (2,4-DCP) is widely distributed in wastewaters discharged from several industries, and it is considered as a priority pollutant due to its high toxicity. In this study, the use of different peroxidase extracts for 2,4-DCP removal from aqueous solutions was investigated. Tobacco hairy roots (HRs), wild-type (WT), and double-transgenic (DT) for tomato basic peroxidases (TPX1 and TPX2) were used to obtain different peroxidase extracts: total peroxidases (TPx), soluble peroxidases (SPx), and peroxidases ionically bound to the cell wall (IBPx). All extracts derived from DT HRs exhibited higher peroxidase activity than those obtained from WT HRs. TPx and IBPx DT extracts showed the highest catalytic efficiency values. The optimal conditions for 2,4-DCP oxidation were pH 6.5, H₂O₂ 0.5 mM, and 200 U mL^?1 of enzyme, for all extracts analyzed. Although both TPx extracts were able to oxidize different 2,4-DCP concentrations, the removal efficiency was higher for TPx DT. Polyethylene glycol addition slightly improved 2,4-DCP removal efficiency, and it showed some protective effect on TPx WT after 2,4-DCP oxidation. In addition, using Lactuca sativa test, a reduction of the toxicity of post removal solutions was observed, for both TPx extracts. The results demonstrate that TPx extracts from both tobacco HRs appear to be promising candidate for future applications in removing 2,4-DCP from wastewaters. This is particularly true considering that these peroxidase sources are associated with low costs and are readily available. However, TPx DT has increased peroxidase activity, catalytic efficiency, and higher removal efficiency than TPx WT, probably due to the expression of TPX1 and TPX2 isoenzymes.