Characterization of products from fluidized-bed combustion of coal

The technology of fluidized-bed combustion (FBC) of coal generates byproducts that have a series of unique characteristics and potential uses in technological practice. In this study, the products of fluidized-bed combustion (FBC-P) of coal derived from Moravian heat stations, a.s. Zlin, Cinergy Global Resources, Czech Republic, were characterized. Particular attention was paid to determining the chemical composition of FBC-P, the content of polycyclic aromatic hydrocarbons (PAHs) and toxic metals in the water leachates of these FBC-P, the content of unburned carbon, the capability of FBC-P to solidify with water and form a solid matrix, and the method for discovering optimum mixing water content for FBC-P solidification. The results suggest that one of the qualitatively more important means of utilizing FBC-P could be their application during solidification/stabilization (S/S) of wastes, particularly wastewater treatment sludges.     

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.     

An evaluation of flare combustion efficiency using open-path Fourier transform infrared technology

Open-path Fourier transform infrared (OP-FTIR) technology was used to evaluate the combustion efficiency of a flare for comparison to several combustion models. Most flares have been considered an effective method for destroying organic compounds and anything that burns. As the Btu content of the flare gas is reduced, the combustion efficiency may also be reduced. Recent studies have suggested that lower Btu flares may have efficiencies as low as 65%. In addition, models have been developed to predict the effect of wind speed and stack discharge velocity on the combustion efficiency. This study was conducted on a low-Btu flare gas that is primarily CO. While the models would predict efficiencies as low as 30%, the sampling using OP-FTIR showed most combustion efficiencies well above 90%. Three methods were used to track combustion efficiency: monitoring the ratio of CO to CO2, monitoring the ratio of CO to tracer gas, and dispersion modeling. This study was complicated by the presence of two flare stacks, thus two tracer gases were used--SF6 and CF4. A method was developed for distinguishing between the two stacks and quantifying the efficiency in each stack.     

Means to improve the effect of in situ bioremediation of contaminated soil: an overview of novel approaches

Different aspects of bacterial degradation of organic contaminants in soil, and how to improve the efficiency and reproducibility is discussed in this review. Although bioremediation in principle includes the use of any type of organism in improving the condition of a contaminated site, most commonly bacteria are the degraders and other organisms, such as soil animals or plant roots, play a role in dissemination of bacteria and, indirectly, plasmids between bacteria, and in providing nutrients and co-substrates for the bacteria active in the degradation process. There are a number of different procedures that have been tested more-or-less successfully in attempts to improve reliability, cost efficiency and speed of bioremediation. The methods range from minimal intervention, such as mere monitoring of intrinsic bioremediation, through in situ introduction of nutrients and/or bacterial inocula or improvement of physico-chemical conditions, all the way to excavation followed by on site or ex situ composting in its different varieties. In the past the rule has been that more intervention (leading to higher costs) has been more reliable, but novel ideas are continuously tried out, both as a means to come up with new truly functional applications and also as a line of studies in basic soil microbial ecology. Both approaches generate valuable information needed when predicting outcome of remediation activities, evaluating environmental risks, deciding on cleaning-up approaches, etc. The emphasis of this review is to discuss some of the novel methods for which the value has not been clearly shown, but that in our view merit continued studies and efforts to make them work, separately or in combination.     

Vertical distribution of Cd, Pb and Zn in soils near smelters in the North of France

The analysis of the horizons of 12 soil profiles confirm occasionally significant levels of Cd, Pb and Zn contamination in the areas surrounding two lead and zinc smelters in the North of France. A pedological approach enabled the original Cd, Pb and Zn content of the horizons to be estimated, based on physico-chemical characteristics of soil unaffected by contamination. The main contamination was found in the upper 20-30 cm. Traces of Cd and Zn contamination were found at a depth of around 2 m. The mobility of the metals may be classified in the following order: Cd>Pb> or =Zn. The concentration profile of a metal seems insufficient to evaluate its movement as the metal could have been leached beyond the contaminated horizons. The depth reached by the metals increases with their concentration in the surface horizon; a decrease in pH and an increase in sand content seem to facilitate their movement. The depth reached by Zn increases with the organic carbon content in the surface horizon. Earthworm galleries act as paths via which metals migrate downwards     

Mussel watch: a review of Cu and other metals in various marine organisms in Taiwan, 1991-98

This study presents the distribution of Cu, Zn, Pb, Cd, Hg and As in various marine organisms collected along the western coast of Taiwan from 1991 to 1998, and also evaluates the time variation of Cu in oysters before (1980-85) and after (1986-98) the "green oyster" incident. The results show that relatively high geometric mean (GM) concentrations of Cu, Zn, Pb, Cd, As and Hg were generally found in Crassostrea gigas (Cu=229 microg/g, Zn=783 microg/g), Gomphina aeguialtera (Pb=30.3 microg/g), Tegillarca granosa (Cd=2.85 microg/g), Thais clavigera (As=96.9 microg/g) and Parapenaeopsis cornuta (Hg=1.35 microg/g), respectively. Especially, maximum Cu and Zn concentrations (GM=229 and 783 microg/g, respectively) in oysters (C. gigas) from different culture areas were much higher than those of the other organisms by about 1.13-458 and 2.40-63.7 times, respectively. Similarly, rock-shells (Thais clavigera) had a high capacity for accumulating Cu (GM=202 microg/g) and Zn (GM=326 microg/g) under the same physico-chemical conditions. The highest GM Cu and Zn concentrations of 1108 (range from 113 to 2806) and 1567 (range from 303 to 3593) microg/g were obtained in oysters from the Hsiangshan coastal area, one of the most important oyster culture areas in Taiwan. However, the highest GM Cd and As concentrations of 6.82 and 19.3 microg/g were found in oysters from the Machu Islands. Mean Cu concentrations in the oysters from the Erhjin Chi estuary declined from 2194+/-212 microg/g in 1986-90 to 545 microg/g (GM) in 1991-96. In the Hsiganshan area, GM Cu concentrations of 909 microg/g (1991-96) and 1351 microg/g (1997-98) in oysters were significantly higher than those of 201 microg/g (1980-85) and 682 microg/g (1986-90). The gradually increasing levels of Cu and Zn in the oysters from the Hsiangshan area have been observed year by year.     

Constructed wetlands for mitigation of atrazine-associated agricultural runoff

Atrazine was amended into constructed wetlands (59-73x14x0.3 m) for the purpose of monitoring transport and fate of the pesticide to obtain information necessary to provide future design parameters for constructed wetlands mitigation of agricultural runoff. Following pesticide amendment, a simulated storm and runoff event equal to three volume additions was imposed on each wetland. Targeted atrazine concentrations were 0 microg/l (unamended control), 73 microg/l, and 147 microg/l. Water, sediment, and plant samples were collected weekly for 35 days from transects longitudinally distributed throughout each wetland and were analyzed for atrazine using gas chromatography. Between 17 and 42% of measured atrazine mass was within the first 30-36 m of wetlands. Atrazine was below detection limits (0.05 microg/kg) in all sediment and plant samples collected throughout the duration of this study. Aqueous half lives ranged from 16 to 48 days. According to these data, conservative buffer travel distances of 100-280 m would be necessary for effective runoff mitigation.     

Application of a stochastic, Weibull probability generator for replacing missing data on ambient concentrations of gaseous pollutants

A stochastic, three-parameter, Weibull frequency distribution, probability generator was tested by using theoretical data. Subsequently, it was applied to replace missing values of hourly atmospheric concentrations of trace gases that were continuously monitored at three study sites, for 2 years. The results were highly accurate and realistic. The cumulative means and the medians calculated by the Weibull method were intermediate between corresponding values calculated by uniform substitution of missing values with 'zero' or with half of the minimum detection limit of the appropriate measurement instrument used. Furthermore, the Weibull method allowed the replacement of as many as 100 missing values on either side of a measured data sub-set, without altering the overall characteristics of the true frequency distribution of the entire data set.     

Acid rain and acidification in China: the importance of base cation deposition

Acid deposition has been recognized as a serious environmental problem in China. Most acid deposition studies have focused on sulfur deposition and the pH of precipitation. However, as high concentration of alkaline dust is an important feature of the atmosphere in large parts of China, base cation deposition must be taken into account when discussing possible effects on soils and vegetation from acid deposition. We estimate the deposition of sulfur as well as calcium, i.e. the dominating anion and cation, on a regional scale in China using data both from measurements and modeling. The ratio of sulfur/calcium in deposition is then used as an indicator for identifying areas where deposition acidity exceeds alkalinity, and where soils may be at risk to acidification. The dynamic soil acidification model MAGIC is applied with data from two sites receiving high deposition loads in southwest China. The model predictions indicate that considerable soil acidification has been going on for the last decades due to acid deposition inputs. Effects on the spatial distribution of acidic deposition in China, using different future deposition scenarios, are illustrated. As the size of the anthropogenic fraction of the base cation deposition is unknown, different possible future trends in calcium deposition were used. Soil response, according to the model, using different combinations of sulfur and calcium deposition scenarios is shown. Applying the most strict measures to reduce sulfur emission will almost eliminate the acid deposition problem; however, such a scenario is not economically feasible in the short term. A strict, but possibly realistic, future scenario for sulfur may be enough to keep the situation at the present level, assuming only moderate reductions in calcium deposition. With large decreases in base cation deposition, increased soil acidification can be expected even with considerable sulfur emission reductions.     

Acute and chronic impacts caused by aromatic hydrocarbons on bacterial communities at Boa Viagem and Forte do Rio Branco Beaches, Guanabara Bay, Brazil

The bacterial community presented significantly different hydrocarbonoclastic activity under acute and chronic impacts. Benzoic acid, toluene, benzene and xylene were used in final concentrations of 5, 10 and 15 mM and bacterial biomass was quantified through protein dosage. Under acute impact, the highest biomass percentages occurred between the 11th and 14th days; under chronic impact, between the 20th and 29th days. Under acute and chronic impacts, the bacterial biomass presented higher nutritional specialization at Boa Viagem Beach, using the aromatic hydrocarbons up to a concentration of 15 mM. Under acute impact, the concentration of the hydrocarbons constituted a critical factor for the bacterial flora from Forte do Rio Beach, because biomass increases only occurred in concentrations of 5 mM; under chronic impact, the aromatic hydrocarbons induced the specialization and increased bacterial biomass for 15 mM toluene. Benzoic acid (15 mM) was used by the bacteria from Boa Viagem and Forte do Rio Branco Beaches.