Observations and analytical modeling of freshwater and rainwater lenses in coastal dune systems

Observations are reported on (i) groundwater recharge rates under various types of vegetation as measured with megalysimeters in the dunes, (ii) freshwater lenses along the Dutch North Sea coast in the early 1900s, and (iii) rainwater lenses that develop on top of laterally migrating, artificially recharged riverwater. Subsequently analytical methods are presented to estimate annual natural groundwater recharge as function of rainfall and vegetation, and to calculate the size, shape and transition zone of freshwater lenses on saline groundwater and rainwater lenses on infiltrated riverwater. An empirical correction factor, based on the hydraulic resistance of an aquitard within the freshwater lens, is proposed to account for the frequently observed reduction of the Ghyben-Herzberg ratio of 40. This factor raises the groundwater table, reduces the depth of the fresh/salt interface and increases the lens formation time. The suite of methods offers a tool box for knowledge based water management of dune systems, by rapidly predicting: (i) more or less autonomous changes due to sealevel rise, climate change and vegetation development; and (ii) the potential (side) effects of interventions. Knowing what happened or will happen to the fresh water lens or a rainwater lens is important, because changes impact on important natural habitat parameters such as salinity, depth to groundwater table, decalcification rate (and thus on pH, Ca/Al, PO₄, NH₄) and nutrient availability, and on drinking water supply. The analytical models are applied to predict effects of sealevel rise, coastal progradation, vegetation changes, and increased temperature of coastal air and river water to be infiltrated.     

2D brine sewage after impinging on a shallow sea free surface

We consider the problem of the vertically upwards disposal of heavy brine sewage from a two-dimensional diffuser in a lighter, homogeneous, motionless and shallow ambient sea. The rejected high salinity water of seawater desalination plants for urban and agricultural uses is such a case of a two dimensional fountain. The disposal of brine sewage produces a negative buoyant jet due to its initial momentum, which impinges on the free surface, spreads laterally on it and then sinks downwards, because of the negative buoyancy. Laboratory experiments and dimensional considerations are used in this paper in order to investigate the spreading behavior (width) of the vertical fountain which impinges on the free surface of the shallow ambient fluid. The experimental results have been used to derive an equation relating the width at the free surface with the initial parameters of the flow. In addition, the experimentally measured dilution of the heavier brine sewage on the recipient’s surface is compared with the dilution which was calculated by a numerical simulation of a well-known commercial software package, CORJET (a CORMIX sub model).     

Modeling and data assessment of longitudinal salinity in a low-gradient estuarine river

Continuous data of vertical-profile salinity were analyzed for four stations located successively upriver in a macrotidal estuary, the lower St. Johns River (Northeast Florida, USA). The data analysis confirmed well-mixed salinity conditions in the river with at most 1.3 ppt of vertical variability at Dames Point (river km 20), where the main variations of salinity are along the longitudinal axis of the river. Given the well-mixed salinity conditions and dominant horizontal structure of salinity variations in the river, we present and apply a barotropic, two-dimensional modeling approach for hydrodynamic-salinity transport simulation in the lower St. Johns River. When properly forced by offshore surge, high-resolution wind fields and freshwater river inflows, the model replicated the salinity measurements remarkably well, including the separation into tidal and sub-tidal components. The data and model results show that, at times, offshore winds and surge can be more influential on longitudinal salinity variations than local winds over the river. We demonstrate the importance of using proper boundary conditions to force the model relative to the minimal sensitivity of the model to parameter adjustment of horizontal mixing and uncertainty-based perturbation of wind and inflow forcings.     

Influence of the secondary motions on pollutant mixing in a meandering open channel flow

This paper presents large eddy simulation of turbulent flow in a meandering open channel with smooth wall and rectangular cross-section. The Reynolds number based on the channel height is 40,000 and the aspect ratio of the cross-section is 4.48. The depth-averaged mean stream-wise velocity agree well to experimental measurements. In this specific case, two interacting cells are formed that swap from one bend to the other. Transport and mixing of a pollutant is analysed using three different positions of release, e.g. on the inner bank, on the outer bank and on the centre of the cross section. The obtained depth-average mean concentration profiles are reasonably consistent with available experimental data. The role of the secondary motions in the mixing processes is the main focus of the discussion. It is found that the mixing when the scalar is released on the centre of the cross-section is stronger and faster than the mixing of the scalar released on the sides. When the position of release is close to a bank side, the mixing is weaker and a clear concentration of scalar close to the corresponding side-wall can be observed in both cases.     

Heavy metals and soil microbes

Heavy metal pollution is a global issue due to health risks associated with metal contamination. Although many metals are essential for life, they can be harmful to man, animal, plant and microorganisms at toxic levels. Occurrence of heavy metals in soil is mainly attributed to natural weathering of metal-rich parent material and anthropogenic activities such as industrial, mining, agricultural activities. Here we review the effect of soil microbes on the biosorption and bioavailability of heavy metals; the mechanisms of heavy metals sequestration by plant and microbes; and the effects of pollution on soil microbial diversity and activities. The major points are: anthropogenic activities constitute the major source of heavy metals in the environment. Soil chemistry is the major determinant of metal solubility, movement and availability in the soil. High levels of heavy metals in living tissues cause severe organ impairment, neurological disorders and eventual death. Elevated levels of heavy metals in soils decrease microbial population, diversity and activities. Nonetheless, certain soil microbes tolerate and use heavy metals in their systems; as such they are used for bioremediation of polluted soils. Soil microbes can be used for remediation of contaminated soils either directly or by making heavy metals bioavailable in the rhizosphere of plants. Such plants can accumulate 100 mg g^?1 Cd and As; 1000 mg g^?1 Co, Cu, Cr, Ni and 10,000 mg g^?1 Pb, Mn and Ni; and translocate metals to harvestable parts. Microbial activity changes soil physical properties such as soil structure and biochemical properties such as pH, soil redox state, soil enzymes that influence the solubility and bioavailability of heavy metals. The concept of ecological dose (ED₅₀) and lethal concentration (LC₅₀) was developed in response to the need to easily quantify the influence of pollutants on microbial-mediated ecological processes in various ecosystems.     

Recycling polymeric waste from electronic and automotive sectors into value added products

The environmentally sustainable disposal and recycling of ever increasing volumes of electronic waste has become a global waste management issue. The addition of up to 25% polymeric waste PCBs (printed circuit boards) as fillers in polypropylene (PP) composites was partially successful: while the tensile modulus, flexural strength and flexural modulus of composites were enhanced, the tensile and impact strengths were found to decrease. As a lowering of impact strength can significantly limit the application of PP based composites, it is necessary to incorporate impact modifying polymers such as rubbery particles in the mix. We report on a novel investigation on the simultaneous utilization of electronic and automotive rubber waste as fillers in PP composites. These composites were prepared by using 25 wt.% polymeric PCB powder, up to 9% of ethylene propylene rubber (EPR), and PP: balance. The influence of EPR on the structural, thermal, mechanical and rheological properties of PP/PCB/ EPR composites was investigated. While the addition of EPR caused the nucleation of the β crystalline phase of PP, the onset temperature for thermal degradation was found to decrease by 8%. The tensile modulus and strength decreased by 16% and 19%, respectively; and the elongation at break increased by ~71%. The impact strength showed a maximum increase of ~18% at 7 wt.%–9 wt.% EPR content. Various rheological properties were found to be well within the range of processing limits. This novel eco-friendly approach could help utilize significant amounts of polymeric electronic and automotive waste for fabricating valuable polymer composites.

Open image in new window

     

Microbial mediated arsenic biotransformation in wetlands

Arsenic (As) is a pervasive environmental toxin and carcinogenic metalloid. It ranks at the top of the US priority List of Hazardous Substances and causes worldwide human health problems. Wetlands, including natural and artificial ecosystems (i.e. paddy soils) are highly susceptible to As enrichment; acting not only as repositories for water but a host of other elemental/chemical moieties. While macroscale processes (physical and geological) supply As to wetlands, it is the micro-scale biogeochemistry that regulates the fluxes of As and other trace elements from the semi-terrestrial to neighboring plant/aquatic/atmospheric compartments. Among these fine-scale events, microbial mediated As biotransformations contribute most to the element’s changing forms, acting as the ‘switch’ in defining a wetland as either a source or sink of As. Much of our understanding of these important microbial catalyzed reactions follows relatively recent scientific discoveries. Here we document some of these key advances, with focuses on the implications that wetlands and their microbial mediated transformation pathways have on the global As cycle, the chemistries of microbial mediated As oxidation, reduction and methylation, and future research priorities areas.

Open image in new window

     

Green Toxicology: a strategy for sustainable chemical and material development

Green Toxicology refers to the application of predictive toxicology in the sustainable development and production of new less harmful materials and chemicals, subsequently reducing waste and exposure. Built upon the foundation of “Green Chemistry” and “Green Engineering”, “Green Toxicology” aims to shape future manufacturing processes and safe synthesis of chemicals in terms of environmental and human health impacts. Being an integral part of Green Chemistry, the principles of Green Toxicology amplify the role of health-related aspects for the benefit of consumers and the environment, in addition to being economical for manufacturing companies. Due to the costly development and preparation of new materials and chemicals for market entry, it is no longer practical to ignore the safety and environmental status of new products during product development stages. However, this is only possible if toxicologists and chemists work together early on in the development of materials and chemicals to utilize safe design strategies and innovative in vitro and in silico tools. This paper discusses some of the most relevant aspects, advances and limitations of the emergence of Green Toxicology from the perspective of different industry and research groups. The integration of new testing methods and strategies in product development, testing and regulation stages are presented with examples of the application of in silico, omics and in vitro methods. Other tools for Green Toxicology, including the reduction of animal testing, alternative test methods, and read-across approaches are also discussed.     

Role of membrane and compound properties in affecting the rejection of pharmaceuticals by different RO/NF membranes

This study was conducted to assess the merits and limitations of various high-pressure membranes, tight nanofiltration (NF) membranes in particular, for the removal of trace organic compounds (TrOCs). The performance of a low-pressure reverse osmosis (LPRO) membrane (ESPA1), a tight NF membrane (NF90) and two loose NF membranes (HL and NF270) was compared for the rejection of 23 different pharmaceuticals (PhACs). Efforts were also devoted to understand the effect of adsorption on the rejection performance of each membrane. Difference in hydrogen bond formation potential (HFP) was taken into consideration. Results showed that NF90 performed similarly to ESPA1 with mean rejection higher than 95%. NF270 outperformed HL in terms of both water permeability and PhAC rejection higher than 90%. Electrostatic effects were more significant in PhAC rejection by loose NF membranes than tight NF and LPRO membranes. The adverse effect of adsorption on rejection by HL and ESPA1 was more substantial than NF270 and NF90, which could not be simply explained by the difference in membrane surface hydrophobicity, selective layer thickness or pore size. The HL membrane had a lower rejection of PhACs of higher hydrophobicity (log D>0) and higher HFP (>0.02). Nevertheless, the effects of PhAC hydrophobicity and HFP on rejection by ESPA1 could not be discerned. Poor rejection of certain PhACs could generally be explained by aspects of steric hindrance, electrostatic interactions and adsorption. High-pressure membranes like NF90 and NF270 have a high promise in TrOC removal from contaminated water.

Open image in new window

     

Recovery of rare and precious metals from urban mines—A review

Urban mining is essential for continued natural resource extraction. The recovery of rare and precious metals (RPMs) from urban mines has attracted increasing attention from both academic and industrial sectors, because of the broad application and high price of RPMs, and their low content in natural ores. This study summarizes the distribution characteristics of various RPMs in urban mines, and the advantages and shortcomings of various technologies for RPM recovery from urban mines, including both conventional (pyrometallurgical, hydrometallurgical, and biometallurgical processing), and emerging (electrochemical, supercritical fluid, mechanochemical, and ionic liquids processing) technologies. Mechanical/physical technologies are commonly employed to separate RPMs from nonmetallic components in a pre-treatment process. A pyrometallurgical process is often used for RPM recovery, although the expensive equipment required has limited its use in small and medium-sized enterprises. Hydrometallurgical processing is effective and easy to operate, with high selectivity of target metals and high recovery efficiency of RPMs, compared to pyrometallurgy. Biometallurgy, though, has shown the most promise for leaching RPMs from urban mines, because of its low cost and environmental friendliness. Newly developed technologies—electrochemical, supercritical fluid, ionic liquid, and mechanochemical—have offered new choices and achieved some success in laboratory experiments, especially as efficient and environmentally friendly methods of recycling RPMs. With continuing advances in science and technology, more technologies will no doubt be developed in this field, and be able to contribute to the sustainability of RPM mining.

Open image in new window