The probabilistic tsunami hazard assessment along Karnataka Coast from Makran Subduction Zone,west coast of India

Coastal tsunami amplitudes were calculated to identify areas susceptible to tsunami hazard at selected locations of the coast of Karnataka, west of India, due to earthquakes in the Makran Subduction Zone. This is the first time that the probabilistic tsunami hazard assessment along this study area has been attempted. A series of earthquake source scenarios with magnitudes of Mw 8.0, Mw 8.5, and a mega thrust of Mw 9.1 were modeled by using the Community Model Interface for Tsunami interface with the MOST model of Titov and Synolakis (J. Waterway, Port, Coastal and Ocean Engineering, 121(6), 308–316, 1995). As per the previous occurrences, the two least magnitudes are probable, while Mw 9.1 is a worst-case scenario as described by Heidarzadeh et al. (Ocean Engineering, 36(5), 368–376, 2009) and the same is reported by Burbidge et al. (Geoscience Australia Professional Opinion No. 2009/11) as high magnitude. These are not at all historical earthquakes or specifically from historical catalogues. The results of modeling show that all the seven coastal locations are inundated barely in our worst-case scenario with maximum water levels in the range of 100–200 cm. The first tsunami wave strikes the coast within 4–5 h of earthquake occurrence.     

An automated (novel) algorithm for estimating green vegetation cover fraction from digital image: UIP-MGMEP

Green vegetation cover fraction (VCF) is an important indicator of vegetation status in ecology and agronomy. Digital image analysis (DIA) has been widely accepted as a new VCF measurement technique. In this study, we present a novel fully automatic threshold segmentation algorithm for VCF measurements, which is named as upper inflection point plus mean gradient magnitude of edge pixels (UIP-MGMEP). The algorithm performs VCF estimation upon the vegetation index Excess Green (EXG). UIP-MGMEP optimizes the EXG threshold by searching the upper inflection point (UIP) of the M-Et curve (mean gradient magnitude of edge pixels (MGMEP) vs. EXG threshold), based on the assumption that EXG variance of the boundary pixels between vegetation and background is larger than the variance of the background. Five typical sample images are used to illustrate how ground complexity reduces the distinctness of the UIP. Three controlled experiments are illustrated to test the robustness of UIP-MGMEP to resolution, exposure, and ground complexity. The results show that UIP-MGMEP is a promising algorithm for automatic VCF estimation upon digital images. Compared to broad-leaved grass, narrow-leaved grass is more sensitive to resolution and exposure. To reduce ground complexity, smaller footprint size while more images to cover the same area may be better than one image with large footprint size. UIP-MGMEP is fully automatic, making it promising for batch processing of VCF measurements that is very difficult in any wide-range field survey in the past. UIP-MGMEP algorithm can only extract green vegetation and is not suitable for non-green (even grayish-green) vegetation, due to the limits of vegetation index EXG. In addition, UIP-MGMEP is not recommended for images with VCF less than 0.5% or greater than 99.5%.     

Real<Emphasis Type="Bold">-</Emphasis>time water quality monitoring using Internet of Things in SCADA

Water pollution is the root cause for many diseases in the world. It is necessary to measure water quality using sensors for prevention of water pollution. However, the related works remain the problems of communication, mobility, scalability, and accuracy. In this paper, we propose a new Supervisory Control and Data Acquisition (SCADA) system that integrates with the Internet of Things (IoT) technology for real-time water quality monitoring. It aims to determine the contamination of water, leakage in pipeline, and also automatic measure of parameters (such as temperature sensor, flow sensor, color sensor) in real time using Arduino Atmega 368 using Global System for Mobile Communication (GSM) module. The system is applied in the Tirunelveli Corporation (Metro city of Tamilnadu state, India) for automatic capturing of sensor data (pressure, pH, level, and energy sensors). SCADA system is fine-tuned with additional sensors and reduced cost. The results show that the proposed system outperforms the existing ones and produces better results. SCADA captures the real-time accurate sensor values of flow, temperature, and color and turbidity through the GSM communication.     

Silver near municipal wastewater discharges into western Lake Ontario,Canada

Because of the widespread use of silver nanoparticles in commercial products, discharges of municipal wastewater may be a point source of silver in the aquatic environment. We monitored two sites in western Lake Ontario impacted by discharges from wastewater treatment plants serving the City of Toronto. Concentrations of silver were elevated in bottom sediments and suspended sediments collected at the two sites. We also deployed two types of passive samplers in the water column at the two sites, the newly developed Carbon Nanotube Integrative Samplers for monitoring “CNIS-labile” silver and Diffusive Gradient in Thin Film samplers for monitoring “DGT-labile” silver. Results from these passive samplers indicated that the concentrations of silver at the two sites were either below detection limits or were in the ng/L range. In laboratory experiments where the sediments were re-suspended in Milli-Q water, a small proportion of the silver (i.e., <?25%) was labile and partitioned as colloidal or dissolved silver into the liquid phase after agitation. Nanoparticles tentatively identified as silver nanoparticles were detected by single-particle ICP-MS in suspension after agitation of both suspended and bottom sediments. Therefore, there is a need to assess whether silver species, including silver nanoparticles are transported from wastewater treatment plants into sediments in the aquatic environment. This study is unique in focusing on the in situ distribution of silver in natural waters and in sediments that are potentially impacted by urban sources of nanoparticles.     

Treatment technologies for PAH-contaminated sites: a critical review

To reduce environmental and human health risks of contaminated sites, having a comprehensive knowledge about the polycyclic aromatic hydrocarbon (PAH) removal processes is crucial. PAHs are contaminants which are highly recognized to pose threats to humans, animals, and plants. PAHs are hydrophobic and own two or more benzene rings, and hence are resistant to structural degradation. There are various techniques which have been developed to treat PAH-contaminated soil. Four distinct processes to remove PAHs in the contaminated soil, thought to be more effective techniques, are presented in this review: soil washing, chemical oxidation, electrokinetic, phytoremediation. In a surfactant-aided washing process, a removal rate of 90% was reported. Compost-amended phytoremediation treatment presented 58–99% removal of pyrene from the soil in 90 days. Chemical oxidation method was able to reach complete conversion for some PAHs. In electrokinetic treatment, researchers have achieved reliable results in removal of some specific PAHs. Researchers’ innovations in novel studies and advantages/disadvantages of the techniques are also investigated throughout the paper. Finally, it should be noted that an exclusive method or a combination of methods by themselves are not the key to be employed for remediation of every contaminated site but the field characteristics are also essential in selection of the most appropriate decontamination technique(s). The remedy for selection criteria is based on PAH concentrations, site characteristics, costs, shortcomings, and advantages.     

Reservoir water quality: a case from Jordan

Jordan relies heavily on reservoirs building and development to cope with water supply challenges, where monitoring and assessment of reservoir water quality are critically important for the sustainable use of these water supplies. Mujib Dam is an important water supply source in central western Jordan. Evaluation of water quality parameters and their spatial distributions (vertical and horizontal) showed near-neutral pH values with nearly similar values from surface to bottom. The vertical profile of DO and TDS in the dammed reservoir showed slight decreasing trends with increasing depth. Although Ca, Mg, Na, and K concentrations varied slightly with depths, their variations showed no trends. Similarly, the vertical and horizontal distribution patterns of Cl, SO₄, HCO₃, NO₃, and PO₄ in Mujib reservoir water showed insignificant variations in surface water layer and relatively unchanged values or decreasing trends through the water column. Higher values of TN have been observed, especially in the western part, suggesting that agricultural activities and livestock farming in the upstream catchment are impacting water quality. Results revealed that weathering and dissolution of rocks are the major source of water chemistry. The majority of trace metal levels (Cd, Cr, Cu, Fe, Mn, Pb, Zn, Co, Ni, Sr, and B) in water showed relatively similar surface and bottom values. The concentrations of COD and BOD₅ in surface water were relatively low with higher concentrations observed in the northwestern corner, coincided with higher levels of chlorophyll a. The average ratio of TN to TP in surface water suggests that phosphorus is the limiting factor for the algal blooms, whereas the average chlorophyll a level in surface water indicates oligo-mesotrophic water.     

FIA-coupled spectrophotometric method for determination of Cr (VI) traces in natural waters: application of in-line dissolution of 1,5-diphenylcarbazide after heat treatment and activated alumina as adsorbent for preconcentration

This work proposes the quantification of Cr (VI) ions in natural waters in trace level, using activated alumina (Al₂O₃) as preconcentration support, controlled in-line dissolution of the solidified chromophore diphenylcarbazide after heat treatment and spectrophotometric detection. The manifold ensures high sensitivity of analytical response, good repeatability, and stability. In this work, optimization of experimental conditions of a flow injection system was chosen as the parameters for greater sensitivity and better selectivity. The selected optimized conditions were 0.30 mol L^?1 for H₂SO₄ concentration, system flow rate as 0.40 mL min^?1, sample injection volume of 192.50 μL, 2 min for preconcentration time, and 0.10 mol L^?1 for eluent concentration. The analytical curves obtained for real sample analysis show linear range from 0.192 to 0.961 μM, linear correlation coefficient R?=?0.9997 and LOD?=?0.024 μM. The preconcentration factor of about four times was obtained through the passage of 800 μL of a standard solution containing 0.961 μM of Cr (VI) through mini-column of preconcentration followed by elution at 192.5 μL of NH₄OH 0.1 mol L^?1 solution. The solid chromogenic reagent presented high durability (weeks in daily use with mass of 0.0993 g) and good reproducibility in analytical signal. The reactivation of the mini-column of alumina should be executed after ten injections of eluent, using 800 μL of HCl 0.02 mol L^?1 solution in flow through the same. Each cycle of injection and elution of the sample takes about 5 min on the proposed terms. Despite the length of each cycle still be high, low concentrations can be detected using a technique of relatively low cost. This is due in part, the association dissolution of the chromogenic reagent directly in the line and the preconcentration step. Another important factor is the economy of reagent chromogenic, low generation of reject contributing to better quality of the environment, and the high potential for applications to work in field.     

Assessment using CFD of the wind direction on the air discharges caused by natural ventilation of a poultry house

Air inside poultry houses must be removed on a regular basis to prevent excess of heat, particles and noxious gases that can imperil animals. To cope with this issue, natural ventilation could be an effective method when assisted by accurate predictions. This study investigates air discharges caused by natural ventilation of a poultry house by means of a three-dimensional computational fluid dynamics (CFD) model. It solves the governing equations of momentum, heat and mass transport, radiative transfers and animal-generated heat. Wind directions of 0°, 36° and 56° (0° corresponds to a wind blowing perpendicular to the ridgeline) were investigated; the CFD model predictions achieved a RMSE of 1.2 °C and 0.6 g[H₂O] kg^?1 [dry air] for internal temperature and absolute humidity, respectively, when air blew with an angle of 36°. Air renewal rates (ARR) were 39.5 (±?1.9), 34.9 (±?2.2) and 33.6 (±?1.7) volumes of the building per hour, when air blew at 0°, 36° and 56°, respectively. Such ARR predictions served to know how the gases contained in air would likely spread downstream from the building in order to define regions of potentially high gas concentration that could endanger neighbouring habitable facilities.     

Use of water quality index and multivariate statistical techniques for the assessment of spatial variations in water quality of a small river

Rapid urban development has led to a critical negative impact on water bodies flowing in and around urban areas. In the present study, 25 physiochemical and biological parameters have been studied on water samples collected from the entire section of a small river originating and ending within an urban area. This study envisaged to assess the water quality status of river body and explore probable sources of pollution in the river. Weighted arithmetic water quality index (WQI) was employed to evaluate the water quality status of the river. Multivariate statistical techniques namely cluster analysis (CA) and principal component analysis (PCA) were applied to differentiate the sources of variation in water quality and to determine the cause of pollution in the river. WQI values indicated high pollution levels in the studied water body, rendering it unsuitable for any practical purpose. Cluster analysis results showed that the river samples can be divided into four groups. Use of PCA identified four important factors describing the types of pollution in the river, namely (1) mineral and nutrient pollution, (2) heavy metal pollution, (3) organic pollution, and (4) fecal contamination. The deteriorating water quality of the river was demonstrated to originate from wide sources of anthropogenic activities, especially municipal sewage discharge from unplanned housing areas, wastewater discharge from small industrial units, livestock activities, and indiscriminate dumping of solid wastes in the river. Thus, the present study effectively demonstrates the use of WQI and multivariate statistical techniques for gaining simpler and meaningful information about the water quality of a lotic water body as well as to identify of the pollution sources.     

Simulating chemistry–aerosol–cloud–radiation–climate feedbacks over the continental U.S. using the online-coupled Weather Research Forecasting Model with chemistry (WRF/Chem)

The chemistry–aerosol–cloud–radiation–climate feedbacks are simulated using WRF/Chem over the continental U.S. in January and July 2001. Aerosols can reduce incoming solar radiation by up to ?9% in January and ?16% in July and 2-m temperatures by up to 0.16 °C in January and 0.37 °C in July over most of the continental U.S. The NO₂ photolysis rates decrease in July by up to ?8% over the central and eastern U.S. where aerosol concentrations are high but increase by up to 7% over the western U.S. in July and up to 13% over the entire domain in January. Planetary boundary layer (PBL) height reduces by up to ?23% in January and ?24% in July. Temperatures and wind speeds in July in big cities such as Atlanta and New York City reduce at/near surface but increase at higher altitudes. The changes in PBL height, temperatures, and wind speed indicate a more stable atmospheric stability of the PBL and further exacerbate air pollution over areas where air pollution is already severe. Aerosols can increase cloud optical depths in big cities in July, and can lead to 500–5000 cm^?3 cloud condensation nuclei (CCN) at a supersaturation of 1% over most land areas and 10–500 cm^?3 CCN over ocean in both months with higher values over most areas in July than in January, particularly in the eastern U.S. The total column cloud droplet number concentrations are up to 4.9 × 10⁶ cm^?2 in January and up to 11.8 × 10⁶ cm^?2 in July, with higher values over regions with high CCN concentrations and sufficient cloud coverage. Aerosols can reduce daily precipitation by up to 1.1 mm day^?1 in January and 19.4 mm day^?1 in July thus the wet removal rates over most of the land areas due to the formation of small CCNs, but they can increase precipitation over regions with the formation of large/giant CCN. These results indicate potential importance of the aerosol feedbacks and an urgent need for their accurate representations in current atmospheric models to reduce uncertainties associated with climate change predictions.