中国原油进口来源国供应安全的定量评估

原油供给安全在中国国家安全中占有重要地位,对其定量评估可为防范风险提供政策参考。采用事件数据分析法定量测度中国与21个主要原油进口来源国之间的双边关系,结果表明：中国与大多数原油贸易伙伴的关系处于中低水平,但近十多年总体保持上升趋势,原油进口存在一定的政治关系风险但趋于下降。选用资源、政治、经济、运输、军事5个方面的11个指标,通过组合赋权法确定指标权重,运用集对分析方法评估中国21个原油进口来源国的供应安全度,并识别主要障碍因子。结果表明：21国供应安全度存在较大差异。部分中东国家、俄罗斯、委内瑞拉、哈萨克斯坦供应安全度较高,多数非洲国家和亚太国家供应安全度较低。供应国的原油资源状况、运输风险、政治风险是制约多数国家供应安全的主要障碍因素。为防范风险,中国需坚持开展多边“能源外交”,扩大战略石油储备等多方面施策方针。     

双酚S在两种典型地带性土壤中的吸附/解吸行为研究

采用批平衡实验方法研究了双酚S（BPS）在两种典型地带性土壤中的吸附/解吸行为.结果表明,吸附动力学曲线符合拟二级动力学方程.吸附等温线呈非线性,且同时符合Freundlich和Langmuir方程.相比而言,BPS更易吸附在高有机质含量的黑土中,298 K反应温度下BPS在黑土和红壤上的最大吸附容量分别为497.8和156.6 mg·kg^-1.吸附到两种土壤中的BPS存在解吸滞后现象,这可能是由于BPS以化学吸附和微孔扩散的形式存在于土壤中的缘故.溶液pH与BPS在土壤中的吸附容量呈负相关关系,即中性形态的BPS比阴离子形态的BPS具有更高的吸附容量.与结构类似物双酚A（BPA）的吸附相比,BPS在土壤中的吸附量更低,因此具有更高的迁移能力,可能会引起更高的环境健康风险.本研究结果为了解BPS在土壤中的迁移规律提供了数据支持.     

北部湾南流江流域土地覆盖及生物多样性模拟

以北部湾独流入海河流南流江流域为研究对象,基于研究区2000年和2015年遥感数据解译的土地利用数据以及社会经济等数据,采用CLUE-S模型对未来2030年生态保护情景、自然增长情景以及粮食安全情景的土地利用格局进行了模拟预测,在此基础上采用InVEST模型对流域过去和未来不同情景的生物多样性进行了评估,探讨了流域生物多样性的生境质量和生境退化程度.结果表明：2000~2015年南流江流域建设用地、园地、水域和未利用地呈现出增加趋势,其中建设用地的增幅最大,而耕地和林地减幅最大.流域土地系统中共存在着34种土地网络转移流关系,上游存在24种,中游20种,下游28种,耕地与建设用地、耕地与林地以及林地与园地之间的转换占到流域总土地利用变化的70.74%.CLUE-S模型模拟未来土地利用的Kappa系数达到0.86,表明模型模拟未来情景的土地利用精度满足要求.2000年、2015年、2030年生态保护情景、2030年自然增长情景以及2030年粮食安全情景流域生境质量总得分和平均得分分别为866630,900357,921055,876231,865370和0.7457,0.7747,0.7925,0.7539,0.7466.2030年3种情景的中上游和下游地区生物多样性都呈现出不同程度的改善趋势,而中游地区则表现出退化趋势.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.