Using flue gas desulfurization gypsum to remove dissolved phosphorus from agricultural drainage waters

High levels of accumulated phosphorus (P) in soils of the Delmarva Peninsula are a major source of dissolved P entering drainage ditches that empty into the Chesapeake Bay. The objective of this study was to design, construct, and monitor a within-ditch filter to remove dissolved P, thereby protecting receiving waters against P losses from upstream areas. In April 2007, 110 Mg of flue gas desulfurization (FGD) gypsum, a low-cost coal combustion product, was used as the reactive ingredient in a ditch filter. The ditch filter was monitored from 2007 to 2010, during which time 29 storm-induced flow events were characterized. For storm-induced flow, the event mean concentration efficiency for total dissolved P (TDP) removal for water passing through the gypsum bed was 73 ± 27% confidence interval (α = 0.05). The removal efficiency for storm-induced flow by the summation of load method was 65 ± 27% confidence interval (α = 0.05). Although chemically effective, the maximum observed hydraulic conductivity of FGD gypsum was 4 L s(-1), but it decreased over time to <1 L s(-1). When bypass flow and base flow were taken into consideration, the ditch filter removed approximately 22% of the TDP load over the 3.6-yr monitoring period. Due to maintenance and clean-out requirements, we conclude that ditch filtration using FGD gypsum is not practical at a farm scale. However, we propose an alternate design consisting of FGD gypsum-filled trenches parallel to the ditch to intercept and treat groundwater before it enters the ditch.     

Visualization and localization of bromotoluene distribution in Hedera helix using NanoSIMS

Some plants are known as indoor air purifiers. A large number of studies report kinetic purification results for an extensive panel of plants, i.e. the pollutant concentration (volatile organic compounds, as known as VOC, most of the time) is continuously monitored by gas chromatography. However, only a few papers describe the mechanisms involved in such processes. This study deals with the use of secondary ion mass spectrometry imaging as an efficient tool to locate atmospheric pollutant as bromotoluene within the Hedera helix plant (leaf, roots) and the substrate on which it was previously grown. Hedera helix plants have been placed in a pollution chamber with control of the exposure parameters. Plant and soil samples excised were transferred into a fixative solution of glutaraldehyde and paraformaldehyde for a few days, were dehydrated using ethanol and were embedded with resin. Cross sections were made from the pale brown solids obtained. Then, a device using a cathodic pulverization device capable of depositing a few nanometers of gold atoms over the sample was used to make the surface electronically conductive for the NanoSIMS. Hence, polluted and unpolluted samples of Hedera helix and substrates were obtained following a careful procedure that allowed for the discrimination between polluted and nonpolluted ones. Nanoscale spatial resolution was an invaluable tool (NanoSIMS) to achieve this, and proved that VOCs, such as bromotoluene, were actually trapped by plants such as Hedera helix.     

Stack Dust Sampling: in-Stack Filter or E.P.A. Train

The Environmental Protection Agency has recommended or specified methods for the measurement of participate concentrations in flue gases. The EPA Train for this measurement originally comprised two segments: the front half and the impinger train downstream from the filter proper. This review examines the controversial areas implicit in the use of this EPA Train or the revised EPA train which eliminates the impinger train.     

Prevention Of Significant Deterioration A Critical Review

Prevention of significant deterioration has been a subject of study and discussion for about ten years. An extensive survey of the legislative and legal aspects of this concept is presented in this review. The growth of the concept and its implementation are subjected to critical scrutiny.     

Emission factors for high-emitting vehicles based on on-road measurements of individual vehicle exhaust with a mobile measurement platform

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO(x)), and particle mass with aerodynamic diameter below 2.5 microm (PM2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO(x), black carbon (BC), PM2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO(x) and CO fleet-average emission factors and more than 60% of PM2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM2.5, and NO(x) tended to cluster among the same vehicles.     

World poverty,another look

The World Bank used the Consumer Price Index (CPI) to calculate changes in the world poverty level (measured in U.S. dollars) prior to 1982. In 1983, the U.S. Bureau of Labor Statistics (BLS) replaced the CPI with several indices including CPI-W which was then adopted by the World Bank. This caused the inflated rate of the U.S. dollars and the percentage of the world population in poverty to be dramatically underestimated. This new incorrect procedure gives 25% (1.5 million) below the poverty line in 2005, while the more appropriate procedure (described herein) gives 52% (3.3 million in 2005). The rapid rise of the poverty line (using the preferable CPI) starting in 1987 occurred at nearly the same time as the peak in per capita annual cereal production.     

Life cycle cost evaluation of the digital opacity compliance system

The US Environmental Protection Agency (EPA) has established EPA Reference Method 9 (Method 9) as the preferred enforcement approach for verifying compliance with federal visible opacity standards. While Method 9 has an extensive history of successful employment, reliance on human observers to quantify visible emissions is inherently subjective, a characteristic that exposes Method 9 results to claims of inaccuracy, bias and, in some cases, outright fraud.The Digital Opacity Compliance System (DOCS), which employs commercial-off-the-shelf digital photography coupled with simple computer processing, is a new approach for quantifying visible opacity. The DOCS technology has been previously demonstrated to meet and, in many cases, surpass the Method 9 accuracy and reliability standards (McFarland et al., 2006). Beyond its performance relative to Method 9, DOCS provides a permanent visual record of opacity, a vital feature in legal compliance challenges.In recent DOCS field testing, the opacity analysis of two hundred and forty one (241) regulated air emissions from the following industrial processes: 1) industrial scrubbers, 2) emergency generators, 3) asphalt paving, 4) steel production and 5) incineration indicated that Method 9 and DOCS were statistically equivalent at the 99% confidence level. However, a life cycle cost analysis demonstrated that implementation of DOCS could potentially save a facility $15,732 per trained opacity observer compared to utilization of Method 9.