环境因子对水蚯蚓呼吸速率的影响研究

水蚯蚓能通过摄食剩余污泥而使污泥减量.因此,本文以颤蚓科蠕虫 (Tubificidae)为研究对象,考察环境因子(水质、水蚯蚓投加量、温度、pH、溶解氧)对水蚯蚓呼吸速率的影响,以探明水蚯蚓生长和新陈代谢的最佳条件,揭示环境因子影响水蚯蚓污泥减量的机理.结果表明,水蚯蚓在"水蚯蚓-微生物"共生系统污泥减量装置出水中的呼吸速率最大,为81.72 mg·g^-1·h^-1·L^-1(以单位体积内每g干重水蚯蚓每小时消耗的O₂质量计(mg)),在蒸馏水中的呼吸速率最小,仅为18.31 mg·g^-1·h^-1·L^-1;在容积为1 L的系统中,水蚯蚓呼吸速率随着投加量增加而逐渐减小,当水蚯蚓投加量为0.25 g (以湿重计)时,呼吸速率最大,为81.72 mg·g^-1·h^-1·L^-1;在8~22℃范围内,水蚯蚓呼吸速率随温度升高而增大,在22~30℃范围内趋势则相反;当pH=8.00±0.05时呼吸速率最大,比其他pH值条件下测得的呼吸速率高1倍多;溶解氧在3.5~4.5 mg·L^-1范围内,水蚯蚓的呼吸速率较高,在此溶解氧范围之外时,水蚯蚓呼吸速率均较低. 该研究结果可为污泥减量中水蚯蚓的培养和应用提供可靠的理论依据,从内在层次上揭示了环境因子影响水蚯蚓生长及代谢,进而影响污泥减量的本质原因.     

流化床焚烧含盐苯胺废液的NOx排放特性

在流化床焚烧实验装置上进行含盐苯胺(C6H5NH2)废液的焚烧实验研究,用IMR-IMR2800P废气分析仪对焚烧尾气成分进行了在线监测,考察了焚烧工艺条件对NOx排放浓度的影响规律.结果显示:采用分级燃烧工艺和提高焚烧温度,可以降低NOx浓度;增大进料速率却导致NOx排放浓度的增加.当过剩空气系数(α)低于1.0时,NOx排放浓度随着α的增大急剧上升;大于1.1时,NOx排放浓度随α增加而减小.苯胺废液高温焚烧时添加氯化钠能降低NOx排放.     

剩余污泥中木质纤维素稳定并转化能源可行性分析

剩余污泥中往往含有大量木质纤维素物质,在厌氧消化过程中难以降解,最终被浓缩于熟污泥中,这就是导致污泥有机物稳定并转化能源效率低下的主要原因之一.本文分析了剩余污泥中木质纤维素的含量与来源;阐述了木质纤维素的结构特点以及对其生物降解的关键技术所在;揭示了污泥常规预处理与木质纤维素预处理存在工艺条件不同的相似技术.文章结合两种预处理技术的特点和工艺条件,从原理、技术等角度分析了通过强化剩余污泥预处理而同时达到破解木质纤维素的技术思路.为此,提出了将污泥细胞破碎与木质纤维素破解耦合的观点,以期将污泥中木质纤维素的稳定与能源转化合二为一,从而构建木质纤维素稳定化、能源化与碳减排三位一体的技术策略     

复合生物絮凝剂CBF-1的絮凝作用机理研究

采取PAC+絮凝剂的复配方式开展高岭土悬浊液烧杯实验,考察了复合生物絮凝剂CBF-1、CBF-1溶解物及微生物絮凝剂MBF8的絮凝特性,并借助iPDA仪分析和扫描电镜、光学显微镜观察等手段,比较分析了絮凝过程及絮体特性的差异.结果表明,各复配絮凝的浊度去除效果排序为CBF-1＞ CBF-1溶解物＞MBF8,CBF-1投加量1 mg·L-1时,浊度去除率可达到97.5％;絮体强度排序为CBF-1＞ CBF-1溶解物＞MBF8,絮体恢复因子排序为MBF8＞CBF-1溶解物＞CBF-1,絮体大小排序为CBF-1＞ CBF-1溶解物＞MBF8.单独投加PAC或投加PAC+MBF8的情况下,形成的絮体形态相对规整、密实;投加PAC+ CBF-1溶解物或投加PAC+ CBF-1形成的絮体则相对无序、疏松,CBF-1作用下絮体大、沉降快.CBF-1中高电荷MBF8组分及大分子羧甲基纤维素、羧甲基多聚糖等组分具有强的电荷中和与桥联协同增效作用;CBF-1还含有纤维素、木质素等大分子量且带多种官能团的不溶性组分,在桥联和吸附过程中也起着重要作用.     

改性壳聚糖CAD与微生物絮凝剂MBF8复配絮凝研究

采用水溶液自由基聚合反应,将丙烯酰胺(AM)、二甲基二烯丙基氯化铵(DMDAAC)接枝到壳聚糖分子上制成了阳离子改性壳聚糖(CAD).经FT-IR、XRD、zeta(ξ)电位、凝胶色谱等分析确定,CAD为淡黄色透明液体,pH值为3.7,相对分子质量为2.88×10⁶,阳离子度为16.7,等电点(0.1%溶液)约为pH值10.5,有效成分2.6%,主要特征官能团有羟基、氨基、季铵基和酰胺基, 呈不规则晶体结构.将CAD与相对分子质量3.67×10⁵的多糖类电负性微生物絮凝剂MBF8复配,对浊度12~460 NTU、离子强度3.0 mmol·L^-1的高岭土悬浊液进行烧杯实验.结果表明,MBF8与CAD的最佳使用方式为先投加MBF8后投加CAD,复配比5:3时效果最好,适用的pH范围为6.0~10.0.采用PAC(3.0 mg·L^-1)+MBF8+CAD(1.0 mg·L^-1)复配絮凝,pH=8.0下,对浊度为110 NTU的高岭土悬浊液,浊度去除率>97%,残余铝<0.08 mg·L^-1,絮体大、沉降快,絮凝效果优于PAC+分子量800万、1200万的阴离子PAM及分子量1500万的阳离子PAM.     

Pollination syndromes ignored: importance of non-ornithophilous flowers to Neotropical savanna hummingbirds

Generalization prevails in flower–animal interactions, and although animal visitors are not equally effective pollinators, most interactions likely represent an important energy intake for the animal visitor. Hummingbirds are nectar-feeding specialists, and many tropical plants are specialized toward hummingbird-pollination. In spite of this, especially in dry and seasonal tropical habitats, hummingbirds may often rely on non-ornithophilous plants to meet their energy requirements. However, quantitative studies evaluating the relative importance of ornithophilous vs. non-ornithophilous plants for hummingbirds in these areas are scarce. We here studied the availability and use of floral resources by hummingbirds in two different areas of the Cerrado, the seasonal savannas in Central Brazil. Roughly half the hummingbird visited plant species were non-ornithophilous, and these contributed greatly to increase the overall nectar availability. We showed that mean nectar offer, at the transect scale, was the only parameter related to hummingbird visitation frequency, more so than nectar offer at single flowers and at the plant scale, or pollination syndrome. Centrality indices, calculated using hummingbird–plant networks, showed that ornithophilous and non-ornithophilous plants have similar importance for network cohesion. How this foraging behaviour affects reproduction of non-ornithophilous plants remains largely unexplored and is probably case specific, however, we suggest that the additional energy provided by non-ornithophilous plants may facilitate reproduction of truly ornithophilous flowers by attracting and maintaining hummingbirds in the area. This may promote asymmetric hummingbird–plant associations, i.e., pollination depends on floral traits adapted to hummingbird morphology, but hummingbird visitation is determined more by the energetic "reward" than by pollination syndromes.     

扑草净降解菌的分离、筛选与鉴定及降解特性初步研究

从安徽农药厂废水处理系统的活性污泥中筛选扑草净(prometryne)降解菌.通过富集驯化和选择性培养筛选纯化细菌,分离到2株细菌,分别命名为P-1、P-2.根据表型特征、生理生化特性和16S rDNA序列同源性分析:P-1为G-,鉴定为苍白杆菌属(Ochrobactrum);P-2为G+,鉴定为芽胞杆菌属(Bacillus).GenBank登录号分别为HM004554和HM004555.通过12 d液体降解实验,菌株P-1、P-2对40 mg.L-1扑草净降解率分别达到46.5%和65.4%.该研究为扑草净的生物降解与污染土壤的生物修复提供了依据.     

深水型水库藻类功能组时空演替及生境变化的影响

藻类功能分组是近年来生态学藻类研究的重要理论和方法.为了探明西安某深水型水源水库藻类功能组时空演替及生境变化的影响,于2011年8月起开展实验研究.研究采用现场在线监测和实验室分析相结合的方法.结果表明,水库藻类可分为10个功能组类别:B、D、P、X1、X3、F、G、J、LM、MP.其中,功能组B、P、F、X1、MP、D、J在水库中较为常见,X3、G、LM出现几率较低,功能组B、D、P、X1、X3的藻类数量占优.通过分析环境因子的变化对功能组时空演替的影响,发现水温为最主要的影响因子.水库藻类生长策略为:春季R/CR策略藻种→春末夏初CR/C策略藻种→夏末秋初C/CR/R/CS/S策略藻种→秋末及冬季CR/R策略藻种.此研究可为深水型水库安全取水提供理论支持.     

Cost-performance analysis of nutrient removal in a full-scale oxidation ditch process based on kinetic modeling

A full-scale oxidation ditch process for treating sewage was simulated with the ASM2d model and optimized for minimal cost with acceptable performance in terms of ammonium and phosphorus removal. A unified index was introduced by integrating operational costs (aeration energy and sludge production) with effluent violations for performance evaluation. Scenario analysis showed that,in comparison with the baseline (all of the 9 aerators activated), the strategy of activating 5 aerators could save aeration energy significantly with an ammonium violation below 10%. Sludge discharge scenario analysis showed that a sludge discharge flow of 250–300 m3/day (solid retention time (SRT), 13–15 days) was appropriate for the enhancement of phosphorus removal without excessive sludge production. The proposed optimal control strategy was: activating 5 rotating disks operated with a mode of "111100100" ( "1"represents activation and "0" represents inactivation) for aeration and sludge discharge flow of 200 m3/day (SRT, 19 days). Compared with the baseline, this strategy could achieve ammonium violation below 10% and TP violation below 30% with substantial reduction of aeration energy cost (46%) and minimal increment of sludge production (< 2%). This study provides a useful approach for the optimization of process operation and control.     

Preparation of MgO/B2O3 coatings by plasma spraying on SUS304 surface and effects of heat-resistant

This study mainly deals with the preparation of MgO/B₂O₃ coatings by plasma spraying on the SUS304 surface and the effects of heatresistant. The power materials of low thermal conductivity were selected to control the heat divergent performance of high temperature parts. The reticular micro-structure between the cover thermal layer and the substrate was prepared by using the plasma spraying method. The powder mixture of MgO and B₂O₃ were selected as spraying materials and the SUS304 was used as the substrate material. The MgO/B₂O₃ coating was prepared on the surface of the SUS304 to provide better cover thermal performance. The properties of the microstructures and the morphologies were studied by Optical Microscope, Scanning Electron Microscope, Electron Probe Microanalyzer, and X-ray Diffraction. The results showed that the cover thermal performance has been improved.