固体超强酸SO4^2-／TiO2-SnO2／Ce^4＋光催化降解含酚废水

采用共沉淀-浸渍法制备了固体超强酸SO4^2-／TiO2-SnO2／Ce^4＋,并用XRD、SEM等方法对其结构进行了表征。以苯酚的光催化降解为反应模型,确定了最佳的工艺条件和催化剂再生方法。结果表明：在pH值为6,苯酚初始浓度为50mg／L,催化剂投加量4g／L,光照距离12cm,光照时间为150min,降解率达67．73％,添加助催化剂H2O2后,反应60min,苯酚降解率达到86．33％,催化剂的最佳再生方法是先用1mol／L的硫酸浸渍24h后,在450℃下焙烧6h。     

Suppression of Soot by Metal Additives During the Combustion of Polystyrene

This paper describes an experimental study on the suppression of soot by metal additives during the combustion of polystyrene (PS). A two-dimensional flame generated by using a Wolfhard-Parker type diffusion flame burner was used to simulate practical combustion situations. The PS was continuously fed to the burner and, by controlling the feed rate, the combustion was maintained at a steady state. The additives tested were the salts of Li, Na, K, Mg, Ca, Sr, and Ba, and the combinations of the salts of K and Ca, Sr, or Ba. These additives were added to the flame in the form of small drops of their aqueous solutions generated by an ultrasonic atomizer. Since the flow rate of the carrier gas (air) is very small, this addition causes no noticeable disturbance to the flame. The effectiveness of the alkali metals follows the order of their ease of ionization, i.e., K > Na > Li, and that of the alkaline-earth metals: Ba > Sr > Ca > Mg. At low addition rates, the effectiveness increases with increasing addition rate but becomes unaffected at high addition rates and the maximum percentage of soot suppressed is approximately 50 percent. The combinations of the two metals (i.e., K and Ca, Sr, or Ba) are much more effective than each single metal at the same addition rates and the maximum percentage of soot suppressed reaches approximately 90 percent. It is proposed that the alkaline-earth metals catalyze the ionization of the alkali metals, thus significantly enhancing the effect on soot suppression.     

Inhalation Transfer Factors for Air Pollution Health Risk Assessment

ABSTRACT

To facilitate routine health risk assessments, we develop the concept of an inhalation transfer factor (ITF). The ITF is defined as the pollutant mass inhaled by an exposed individual per unit pollutant mass emitted from an air pollution source. A cumulative population inhalation transfer factor (PITF) is also defined to describe the total fraction of an emitted pollutant inhaled by all members of the exposed population. In this paper, ITFs and PITFs are calculated for outdoor releases from area, point, and line sources, indoor releases in single zone and multizone indoor environments, and releases within motor vehicles. Typical PITFs for an urban area from emissions outdoors are ~10^-6–10^-3. PITFs associated with emissions in buildings or in moving vehicles are typically much higher, ~10^-3–10^-1.     

Theoretical evaluation of the configurations and Raman spectra of 209 polychlorinated biphenyl congeners

Though polychlorinated biphenyls (PCBs) have distributed as threats in the environment to human beings for several decades, monitoring of trace level PCBs in-field is still a challenge. As a potential method for monitoring PCBs at trace levels, Raman spectroscopy has been used to detect several PCBs in the laboratory. To facilitate the development of rapid detection of PCBs by Raman spectroscopy, it is essential to investigate the Raman spectra of all PCB congeners. Herein, the stable configurations and vibrational spectra of all the PCB congeners were calculated by Gaussian 03 program package. Based on molecular symmetry, PCBs are classified into seven groups. The structural features and the normal vibration modes for each group are discussed. Taking the C(2)-2 group as an example, the wavenumber ranges of the various normal vibration modes in the Raman spectra of PCBs were analyzed. The accuracy of calculated results was verified by experimental Raman spectra of PCB77 standard. This study can elucidate further information to promote the development of Raman spectroscopy in environmental monitoring.     

Photocatalytic degradation of triclocarban in aqueous solution using a modified zeolite/TiO2 composite: kinetic,mechanism study and toxicity assessment

Environmental Science and Pollution Research - The current work aimed to investigate the degradation of the triclocarban (TCC) in aqueous solution using a modified zeolite/TiO2 composite (MZTC)...     

多孔喷头射流特性的实验研究

在没有密度分层的容泄水体条件下,对某污水排海工程多孔喷头的射流特性进行了实验研究。文中介绍了不同排污流量和环境流速条件下,多孔喷头附近的流速场和污水场特性;并对出流平均稀释度作了分析。最后,还对该喷头周围的冲淤形态进行了探讨.文中所得的结果对实际排污系统的设计和进一步研究有一定的参考价值。      

PDMDAAC改性粉煤灰预处理油墨废水的研究

本文介绍聚二甲基二烯丙基氯化铵（PDMDAAC）改性粉煤灰的制备,并用制备的改性粉煤灰处理实际油墨废水。研究改性粉煤灰的投加量、反应时间、废水pH值、水温对废水有机物CODG和色度去除率的影响。研究表明在最佳的试验条件下．油墨废水的脱色率高达94％,CODCr去除率也达到了74％。     

The treatment of black-odorous water using tower bipolar electro-flocculation including the removal of phosphorus,turbidity, sulfion,and oxygen enrichment

• An innovative bubble column tower BPE was designed to treat the black-odorous water. • PO₄³⁻, S²⁻ and turbidity were removed, and dissolved oxygen was enriched in the BPE. • An aluminum bipolar electrode gave the best oxygen enrichment and pollutant removal. • Changes of microorganisms confirmed the improvement in water quality achieved. The large amount of municipal wastewater discharged into urban rivers sometimes exceeds the rivers’ self-purification capacity leading to black-odorous polluted water. Electro-flocculation has emerged as a powerful remediation technology. Electro-flocculation in a bubble column tower with a bipolar electrode (BPE) was tested in an attempt to overcome the high resistance and weak gas-floatation observed with a monopolar electrode (MPE) in treating such water. The BPE reactor tested had a Ti/Ta₂O₅-IrO₂ anode and a graphite cathode with an iron or aluminum bipolar electrode suspended between them. It was tested for its ability to reduce turbidity, phosphate and sulphion and to increase the concentration of dissolved oxygen. The inclusion of the bipolar electrode was found to distinctly improved the system’s conductivity. The system’s electro-flocculation and electrical floatation removed turbidity, phosphate and sulphion completely, and the dissolved oxygen level improved from 0.29 to 6.28 mg/L. An aluminum bipolar electrode performed better than an iron one. Changes in the structure of the microbial community confirmed a significant improvement in water quality.     

Digestion of waste bananas to generate energy in Australia

This paper presents results from laboratory studies to measure the methane yield and rate of digestion of reject bananas. These parameters were determined in experiments that took into account the likely configuration of a full-scale plant in the banana growing region of north Queensland. The digestion was conducted in a 200-l reactor using fed-batch operation, relying entirely on the natural microbial consortia on the reject bananas to avoid reliance on external inocula such as sludge, an undesirable material around food packaging facilities. An enrichment culture was first established in a highly buffered 200-l batch digestion unit. The fed-batch digester was then started by exchanging leachate with the mature batch reactor. Under loading conditions of 0.6 kg VS m(-3)d(-1) over 70 days where the average working volume was 160 l, the digester produced 398+/-20 l CH4 kg VS(-1). Increasing the loading rate to 1.6 kg VS m(-3)d(-1) resulted in a reduced methane yield of 210 l CH4 kg VS(-1) over 23 days of operation, with a concomitant accumulation of banana waste in the digester. The leachate at the end of digestion contained over 4000 mg l(-1)K, 200 mg l(-1) N and 75 mg l(-1), levels that exceed acceptable limits for general agricultural irrigation.