Effects of Compounded Curing Agents on Properties and Performance of Urea Formaldehyde Resin

The effects of three compounded curing agents on the properties and performance of the urea-formaldehyde (UF) resin were investigated in this study. The compounded curing agents were prepared by mixing ammonium chloride with hexamethylenetetramine, citric acid, and oxalic acid respectively at a ratio of 1:1, named N-H, N–CA, and N–OA, respectively. The curing process, crystallinity, and physical properties were measured, and the three-ply plywood was fabricated to measure its prepress strength, wet shear strength, and formaldehyde emission. Results showed that the compounded curing agents N–CA and N–OA enhanced the initial viscosity, crosslinking density and thermal stability of UF resin. Additionally, the prepress strength of the plywood bonded by UF resin with N–CA and N–OA increased by 82 and 111% respectively compared to the UF resin with NH₄Cl, and the wet shear strength increased by 14 and 16%, the formaldehyde emission decreased by 19 and 42% respectively. However, owing to the short pot-life of these curing agent limited their storage time, the curing agents N–CA and N–OA should be applied to fabricate plywood in winter for obtaining a better bond strength and a lower formaldehyde emission. While the UF resin with N–HT showed a suitable pot-life, so it could be applied to fabricate plywood in summer for long time storage and avoiding procuring problem.     

Recovery of silicon powder from kerf loss slurry waste using superconducting high gradient magnetic separation technology

A major challenge in recycling of silicon powder from kerf loss slurry waste is the complete removal of metal particles. The traditional acid leaching method is costly and not green. In this paper, a novel approach to recover high-purity Si from the kerf loss slurry waste of solar grade silicon was investigated. The metal impurities were removed with superconducting high gradient magnetic separation technology. The effects of process parameters such as magnetic flux density, slurry density, and slurry flow velocity on the removal efficiency were investigated, and the parameters were optimized. In one lot of control experiments, the silicon content was increased from 90.91 to 95.83%, iron content reduced from 3.24 to 0.57%, and aluminum content from 2.44 to 1.51% under the optimum conditions of magnetic flux density of 4.0 T, slurry density of 20 g/L, and slurry flow velocity of 500 mL/min. The result indicates that the superconducting high gradient magnetic separation technology is a feasible purifying method, and the magnetic separation concentrate could be used as an intermediate product for high-purity Si powder.

     

Approach to the management of magnesium slag via the production of Portland cement clinker

Journal of Material Cycles and Waste Management - This work aims to develop another approach to the management of magnesium slag (MS) via the production of Portland cement clinker. Thus, 0, 10, 20,...     

Polychlorinated biphenyls (PCBs) and halogenated flame retardants (HFRs) in multi-matrices from an electronic waste (e-waste) recycling site in Northern China

The present study investigated the occurrence of polychlorinated biphenyls (PCBs) and halogenated flame retardants (HFRs) in soil, water, reed, air and dust samples collected from the e-waste recycling region in Ziya Town, Northern China. The results showed that the concentrations of PCBs reached relative high level in environmental matrices in the study area. HFRs including polybrominated diphenyl ethers (PBDEs), dechlorane plus (DP), allyl 2,4,6-tribromophenyl ether (ATE), tetrabromoethylcyclohexane (TBECH), pentabromotoluene (PBT), pentabromoethylbenzene (PBEB), 2,3-dibromopropyl 2,4,6-tribromophenyl ether (DPTE), 1,2-bis-(2,4,6-tribromophenoxy) ethane (BTBPE) and so on were also widely detected in multi-matrices. Long-range atmospheric transport (LRAT) potentials of non-BDE HFRs were assessed to address the LRAR abilities of these compounds. Analysis of soil–air exchange of PCBs and HFRs showed that soil acted as a secondary source to the atmosphere only for a few low molecular weight compounds, while the direction of the flux of most detected chemicals was from air to soil.     

Irrigation Water Allocation Using an Inexact Two‐Stage Quadratic Programming with Fuzzy Input under Climate Change

Agricultural irrigation accounts for nearly 70% of the total water use around the world. Uncertainties and climate change together exacerbate the complexity of optimal allocation of water resources for irrigation. An interval‐fuzzy two‐stage stochastic quadratic programming model is developed for determining the plans for water allocation for irrigation with maximum benefits. The model is shown to be applicable when inputs are expressed as discrete, fuzzy or random. In order to reflect the effect of marginal utility on benefit and cost, the model can also deal with nonlinearities in the objective function. Results from applying the model to a case study in the middle reaches of the Heihe River basin, China, show schemes for water allocation for irrigation of different crops in every month of the crop growth period under various flow levels are effective for achieving high economic benefits. Different climate change scenarios are used to analyze the impact of changing water requirement and water availability on irrigation water allocation. The proposed model can aid the decision maker in formulating desired irrigation water management policies in the wake of uncertainties and changing environment.     

Structure optimization and annual performance analysis of the lens-walled compound parabolic concentrator

The primary lens-walled compound parabolic concentrator (lens-walled CPC) has a significant advantage of a larger half acceptance angle as a static solar concentrator, but it also has a drawback of a low optical efficiency. In order to overcome this drawback, in this article, series of structure parameters were investigated and compared to further improve the optical efficiency within the half acceptance angle combined with the material properties. The average optical efficiencies of the improved lens-walled CPCs could achieve more than 82% within the half acceptance angle of 35?. Experiments were adopted to verify the credibility and validity of the simulation. Moreover, annual performance of the lens-walled CPCs comparison with that of the mirror CPC for Nottingham was analyzed. Results show that the improved lens-walled CPC has a higher optical performance for actual building application.