Activated carbon coated palygorskite as adsorbent by activation and its adsorption for methylene blue

An activation process for developing the surface and porous structure of palygorskite/carbon(PG/C) nanocomposite using ZnC l2 as activating agent was investigated. The obtained activated PG/C was characterized by X-ray diffraction(XRD), Fourier transform infrared spectroscopy(FTIR), field-emission scanning electron microscopy(SEM), and Brunauer–Emmett–Teller analysis(BET) techniques. The effects of activation conditions were examined,including activation temperature and impregnation ratio. With increased temperature and impregnation ratio, the collapse of the palygorskite crystal structure was found to accelerate and the carbon coated on the surface underwent further carbonization. XRD and SEM data confirmed that the palygorskite structure was destroyed and the carbon structure was developed during activation. The presence of the characteristic absorption peaks of C_C and C–H vibrations in the FTIR spectra suggested the occurrence of aromatization. The BET surface area improved by more than 11-fold(1201 m2/g for activated PG/C vs. 106 m2/g for PG/C) after activation, and the material appeared to be mainly microporous. The maximum adsorption capacity of methylene blue onto the activated PG/C reached 351 mg/g. The activated PG/C demonstrated better compressive strength than activated carbon without palygorskite clay.     

Do vehicular emissions dominate the source of C6–C8 aromatics in the megacity Shanghai of eastern China?

The characteristic ratios of volatile organic compounds(VOCs) to i-pentane, the indicator of vehicular emissions, were employed to apportion the vehicular and non-vehicular contributions to reactive species in urban Shanghai. Two kinds of tunnel experiments, one tunnel with more than 90% light duty gasoline vehicles and the other with more than 60% light duty diesel vehicles, were carried out to study the characteristic ratios of vehicle-related emissions from December 2009 to January 2010. Based on the experiments, the characteristic ratios of C6–C8aromatics to i-pentane of vehicular emissions were 0.53 ± 0.08(benzene), 0.70 ± 0.12(toluene),0.41 ± 0.09(m,p-xylenes), 0.16 ± 0.04(o-xylene), 0.023 ± 0.011(styrene), and 0.15 ± 0.02(ethylbenzene), respectively. The source apportionment results showed that around 23.3% of C6–C8 aromatics in urban Shanghai were from vehicular emissions, which meant that the non-vehicular emissions had more importance. These findings suggested that emission control of non-vehicular sources, i.e. industrial emissions, should also receive attention in addition to the control of vehicle-related emissions in Shanghai. The chemical removal of VOCs during the transport from emissions to the receptor site had a large impact on the apportionment results. Generally, the overestimation of vehicular contributions would occur when the VOC reaction rate constant with OH radicals(k OH) was larger than that of the vehicular indicator, while for species with smaller k OH than the vehicular indicator, the vehicular contribution would be underestimated by the method of characteristic ratios.     

HF对Cu-SSZ-13/堇青石的原位合成及脱除NO_x的影响

以Cu-TEPA为模板剂原位水热合成一系列具有优良deNOx特性的Cu-SSZ-13/堇青石整体式催化剂.为进一步改善其氨的选择性催化还原氮氧化物的活性,在制备过程中添加HF对原位制备Cu-SSZ-13/堇青石整体式催化剂进行改性.利用XRD、SEM、XPS、BET、ICP-AES等对样品进行了表征.结果表明,当nHF/nAl在0.015—0.0375时,晶化72 h的Cu-SSZ-13/堇青石表现出了优异的脱硝性能和抗老化性能,其最大转化率为99.8%,NOx转化率保持在90%以上的最宽活性温度窗口为280—640℃,而无HF的新鲜样品的NOx转化率保持在90%以上的活性温度窗口为300—580℃;720℃老化50 h处理后,nHF/nAl=0.015—0.0375样品的NOx转化率保持在90%以上的最宽活性温度窗口为360—520℃,未添加HF的老化样品相应的活性温度窗口为400—500℃.无论新鲜还是老化,nHF/nAl=0.015—0.0375样品在低温段200—300℃和高温段500—700℃的NOx转化率基本都大于未添加HF的样品.结合表征结果,在催化剂原位水热合成过程中HF的加入既提高了样品的相对结晶度和负载量,又增大了样品的比表面积和比孔容,且提高了Cu-SSZ-13/堇青石骨架结构的稳定性,进而在一定程度上改善了Cu-SSZ-13/堇青石的高温脱硝活性和水热稳定性.     

不同基质组合对氮磷吸附能力的研究

就地利用菜地改建小型湿地系统可能是实现农村生活污水消纳和资源化利用的一种有效途径,其中菜园土与吸附基质的组合直接关系水体污染物中氮磷的净化效果. 选取沸石、谷壳、活性炭、陶粒和菜园土作为试验基质,使用BET比表面积孔径分析仪、扫描电子显微镜和Ｘ射线衍射仪(EDX)对其进行表征,通过等温吸附试验分别筛选出对氮磷吸附效果较好的沸石和陶粒,设置菜园土∶陶粒∶沸石质量占比基质组合:F1(10∶0∶0)、F2(6∶2∶2)、F3(8∶1∶1)、F4(8∶2∶0)、F5(8∶0∶2)、F6(6∶1∶3)和F7(6∶3∶1). 在低、中、高3种氮磷浓度下,通过吸附动力学试验筛选出去除效果最好的基质组合. 结果表明:①5种单一基质中,活性炭、陶粒的比表面积(35.72、33.23 m2/g)和微孔体积(2.20×10?1、8.25×10?2 cm2/g)均较大;沸石和陶粒表面呈粗糙多孔结构. ②Freundlich和Langmuir等温吸附模型均能较好地拟合5种单一基质对氮磷的吸附,各基质对氮的饱和吸附量表现为沸石(2.00 mg/g)>陶粒(1.47 mg/g)>菜园土(1.17 mg/g)>活性炭(0.99 mg/g)>谷壳(0.21 mg/g),对磷的饱和吸附量表现为陶粒(1.28 mg/g)>活性炭(1.25 mg/g)>沸石(1.16 mg/g)>谷壳(0.80 mg/g)>菜园土(0.50 mg/g). ③7种基质组合对氮磷吸附具有相似的动力学特征,Elovich模型、双常数速率模型和一级反应动力学模型均能较好地模拟基质组合对不同污染负荷条件下氮磷的吸附规律. ④7种基质组合对氮磷的吸附速率均呈现先快后慢的趋势,最终于12~48 h趋于稳定. 研究显示,F2、F4和F7基质组合对氮磷的去除效果均较好,但考虑菜地改造的简易性和可操作性,F4为最佳基质组合,其在3种不同氮磷浓度下对氮、磷的吸附量分别为0.36~0.68和0.10~0.39 mg/g.      

火焰原子吸收光度法测定水中铝的方法改进

研究了在盐酸介质中，壬基酚聚氧乙烯-7醚（NP-7）活化下，火焰原子吸收光度法测定环境水体中铝的方法改进。在25mL容量瓶中，加入5．0mL体积分数为50％的盐酸、2．0mL质量浓度为0．01g／mL NP-7和4．0mL质量浓度为75．0μg/mL的铝标准溶液，在原子吸收分光光度计的最佳测定条件下测定吸光度。根据吸光度与铝质量浓度绘制了工作曲线，线性范围3．0～24．0μg/mL，检出限1．32μg/mL。该法用于环境水体中铝含量的测定，加标回收率为94．4％～101．4％，最大相对标准偏差5．8％，方法对比最大相对误差4．1％。     

道南膜技术测定Ca(NO3)2溶液体系中汞的化学形态

虽然道南膜技术(DMT)已经成功用于土壤/溶液中多种重金属自由态离子浓度的测定,但DMT技术测定Hg的形态尚未解决.采用DMT测定Ca(NO3)2溶液体系中Hg化学形态.实验结果表明,Hg在阳离子交换膜内的吸附除静电吸附外还存在结合力更强的化学吸附,Hg在阳离子交换膜内扩散成为Hg跨膜传输受阻的主要因素,限制道南膜技术用于Hg形态测定.Hg2+和Hg(OH)2都表现出在阳离子交换膜上的强烈吸附,供端(Donor)Hg损失达50%以上.缩短试验时间至8h以内,可在一定程度上降低Hg吸附.计算结果表明,由于大量的Hg滞留在阳离子交换膜内,在计算受端(Acceptor)Hg浓度时引入滞留系数补偿供端Hg的损失,较好地预测了Ca(NO3)2溶液体系中Hg的化学形态.     

济南市大气颗粒物特征及来源的研究

在济南市区设11个点位,在不同季节采集大气颗粒物,其中五个点位用六级串级式采样器采集飘尘样。样品分析了40多种元素、非金属和有机物,并分析了不同粒径中苯并(a)芘含量。应用富集因子计算并提出富集值大干5(EF>5)为污染富集的论点;摸清了济南大气颗粒物的理化特征及粒径分布规律;用化学质量平衡(CMB_7)法探寻了颗粒物来源。     

某二高线通风改造实践研究

根据自然通风原理,对某二高线厂房进行了通风改造,主要从以下三方面人手：在进风窗下增设百页进风口、用通风栅栏代替封闭平台以及扩大天窗喉口。改造前后气流及温度分布的实测结果表明,改造后工作区的热环境得到了较大的改善,气流分布均匀,温度下降明显,提高了人体舒适性。     

废催化剂中金属组分回收利用概述

废催化剂中金属组分的回收利用具有经济性和环保性,从工程项目开发的角度,对废催化剂中金属组分回收利用技术与经济等方面的问题进行了概述,主要包括废催化剂原料的收集与分类、回收技术方案选择、经济评价及关键理论,同时也指出了相关问题及发展前景。     

In situ electron-induced reduction of NOx via CNTs activated by DBD at low temperature

• An in situ electron-induced deNO_x process with CNT activated by DBD was achieved. • Carbon atoms on CNT surface were verified to be excited by plasma in DBD-CNT system. • Reactions between NO_x and excited C result in synergistic effect of DBD-CNT system. In this study, a new in situ electron-induced process is presented with carbon nanotubes (CNTs) as a reduction agent activated by dielectric barrier discharge (DBD) for nitrogen oxide (NO_x) abatement at low temperature (<407 K). Compared with a single DBD system and a DBD system with activated carbon (DBD-AC), a DBD system with carbon nanotubes (DBD-CNT) showed a significant promotion of NO_x removal efficiency and N₂ selectivity. Although the O₂ content was 10%, the NO_x conversion and N₂ selectivity in the DBD-CNT system still reached 64.9% and 81.9% at a specific input energy (SIE) of 1424 J/L, and these values decreased to 16.8%, 31.9% and 43.2%, 62.3% in the single DBD system and the DBD-AC system, respectively. X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were utilized to investigate surface changes in the CNTs after activation by DBD to explore the NO_x reduction abatement mechanism of this new process. Furthermore, the outlet gas components were also observed via Fourier transform infrared spectroscopy (FTIR) to help reveal the NO_x reduction mechanism. Experimental results verified that carbon atoms excited by DBD and the structure of CNTs contributed to the synergistic activity of the DBD-CNT system. The new deNO_x process was accomplished through in situ heterogenetic reduction reactions between the NO_x and carbon atoms activated by the plasma on the CNTs. In addition, further results indicated that the new deNO_x process exhibited acceptable SO₂ tolerance and water resistance.