pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

Ozone pollution characteristics and sensitivity analysis using an observation-based model in Nanjing, Yangtze River Delta Region of China

Ground-level ozone (O₃) has become a critical pollutant impeding air quality improvement in Yangtze River Delta region of China. In this study, we present O₃ pollution characteristics based on one-year online measurements during 2016 at an urban site in Nanjing, Jiangsu Province. Then, the sensitivity of O₃ to its precursors during 2 O₃ pollution episodes in August was analyzed using a box model based on observation (OBM). The relative incremental reactivity (RIR) of hydrocarbons was larger than other precursors, suggesting that hydrocarbons played the dominant role in O₃ formation. The RIR values for NO_X ranged from –0.41%/% to 0.19%/%. The O₃ sensitivity was also analyzed based on relationship of simulated O₃ production rates with reductions of VOC and NO_X derived from scenario analyses. Simulation results illustrate that O₃ formation was between VOCs-limited and transition regime. Xylenes and light alkenes were found to be key species in O₃ formation according to RIR values, and their sources were determined using the Positive Matrix Factorization (PMF) model. Paints and solvent use was the largest contributor to xylenes (54%), while petrochemical industry was the most important source to propene (82%). Discussions on VOCs and NO_X reduction schemes suggest that the 5% O₃ control goal can be achieved by reducing VOCs by 20%. To obtain 10% O₃ control goal, VOCs need to be reduced by 30% with VOCs/NO_X larger than 3:1.     

东平湖DOM荧光特征及与氢氧同位素指标的相关性

本研究在运用三维荧光光谱示踪平水期东平湖DOM荧光特征的基础上,进一步分析其与氢氧同位素指标的相关性,并在此基础上尝试对大气降水的DOC贡献进行估算,以期为东平湖的污染控制及治理提供依据.结果表明,东平湖平水期DOM主要由类蛋白组分（C1和C4）和类腐殖质组分（C2和C3）构成,以类酪氨酸组分C1为主,C1所占比重将近50%.平水期东平湖DOM同时受陆源、内源及大气降水的影响,但以内源输入为主;外源输入中大气降水补给与大汶河输入所占比例相当;大气降水中的溶解性有机碳输入可能会对东平湖DOM产生不可忽视的影响,需进一步系统研究.氢氧稳定同位素与溶解态有机碳以及类腐殖质荧光之间呈显著相关关系,可以在一定程度上指示DOM的变化趋势.     

含菌气溶胶扩散对人群的潜在影响风险

为分析生物气溶胶释放对人群潜在影响风险的情况,利用CALPUFF模型定量模拟了2019年7月24~8月20日中牧兰州生物药厂含菌气溶胶扩散、浓度空间分布、对人群潜在健康风险,并结合公开报道的检测数据开展验证.结果显示：生物药厂的含菌气溶胶排放源附近高值区主要集中于厂区四周,影响范围主要以厂区为中心,并向四周逐渐扩散;检测结果中兰州兽研所1#,兰州大学2#地区健康风险比例41.49：1,在模拟的相对风险大小的误差区间（36.15±8.48）范围内,说明本研究含菌气溶胶对人群潜在影响风险的模拟结果可信.     

中国报废汽车中铂族金属回收潜力估算

基于Gompertz模型预测中国2018~2050年民用汽车的社会保有量;在此基础上,采用物质流分析方法估算得出我国汽车高峰报废年限大约为9a.然后,通过市场供给A模型预测我国2018~2025年汽车报废量,结果显示,我国汽车报废量到2025年将达到2535.05万辆,并且地理空间分布极不均衡.基于上述汽车报废量的时空分布,测算不同技术发展情景下废汽车三元催化剂中的铂族金属回收潜力和需求量.结果显示：如果按照当前催化剂消耗水平,全国铂族金属的需求量均在2019年达到峰值,铂钯铑分别达到4.57,65.70,7.92t,有望实现行业内闭环供应;如果以欧盟汽车尾气治理标准为目标,而现有汽车技术不发生根本变化,需求量将大幅增加,铂钯铑分别在2020年达到峰值85.01,109.38,8.37t,存在严重的供需矛盾.为此,建议在汽车生产者责任延伸制度中,关注废催化剂的回收和再生利用,以促进前端生产环节在不同技术选择中考虑稀贵金属的供给限制.     

乙醇汽油对国六直喷汽油车排放特性的影响

选择5台国六直喷汽油车采用3种不同组分的E10乙醇汽油和1种不含含氧化合物的国VI汽油,按照国六排放标准开展了WLTC循环测试,研究乙醇和基础油组分对污染物排放的影响规律.结果表明,多数国六直喷汽油车的CO、THC和PM排放有所降低,NO_x排放无明显差异,PN排放微增,所有样车的CO、THC和PM平均排放降低为6%、7%和14%.E10乙醇汽油中的重质芳香烃含量增高时,PN排放明显增加,PN排放与PMI指数呈现较强的正相关关系.     

京津冀地区钢铁行业协同减排成本-效益分析

京津冀地区是我国钢铁行业布局最集中的区域,也是大气污染治理的重点区域之一.分析京津冀地区钢铁行业各类治污手段中长期减排的成本-效益,对于选择最经济有效的减排路径、加快推动该地区大气环境质量达标意义重大.基于能源环境、环境分布、人群健康效益评价等模块构建多模型耦合方法,以2015年为基准年,以每5 a为时间节点,设计了京津冀地区钢铁行业规模-结构、规模-技术、规模-末端治理、综合减排4种协同减排情景,计算各情景下2015—2030年京津冀地区钢铁行业主要污染物(SO₂、NO_x、PM₁₀、PM_2.5、CO₂)的减排成本与效益,比较获取治污减排的最优路径方案.结果表明:①基于减排成本计算,规模-末端治理减排情景成本最低,分别为规模-结构、规模-技术减排情景投入的15.18%、23.94%;综合减排情景下治污减排潜力最大,但综合成本最高.②基于环境税效益评价方法、人群健康效益评价方法计算显示,人群健康效益评价方法计算的减排效益高于环境税效益评价方法,表明污染减排的潜在人群健康效益更高;基于两种减排效益方法,4种协同减排情景中综合减排效益分别为10.78×108、76.14×108元,高于规模-结构、规模-技术、规模-末端治理减排情景效益.③基于环境税效益评价方法,4种协同减排情景的效益-成本比表现为规模-末端治理减排情景(0.46) >规模-技术减排情景(0.24) >综合减排情景(0.15) >规模-结构减排情景(0.10);基于人群健康效益评价方法4种协同减排情景的效益-成本比依次为规模-末端治理减排情景(8.35) >综合减排情景(1.07) >规模-结构减排情景(0.57) >规模-技术减排情景(0.65),表明规模-末端治理减排情景的减排路径最优.研究显示,京津冀地区钢铁行业应基于环境质量底线目标要求,综合考虑减排潜力、减排成本与收益,以规模-末端治理为主要途径,选取协同减排的最优路径.