一种包埋微生物复合填料的制备及性能评价

采用包埋法制备出一种复合生物填料,测其各项理化性质,并以NO。模拟废气验证其脱硝性能。填料主要由碳酸钙、牛粪堆肥腐殖质、菌剂载体、水泥、轻质珍珠岩、立体网状纤维及脱硝功能微生物等复合而成,粒径书12mm×20mm,自然堆积密度（471±0．8）kg／m2,持水量（49±1．3）％,比表面积3．91m2／g,平均机械强度（427．3±0．2）N,pH为10．5-0．2。填料能长期在潮湿环境中保持良好的粘结强度,并具有营养缓释及pH缓冲能力。包埋脱硝功能微生物复合填料中初期微生物数量5．3×10^5 CFU／g,运行60d后微生物数量达到8．6×10 8 CFU／g,闲置停运30d微生物有所减少,但重启后净化效率基本不变。当进气负荷低于I878mg／（13m3·h）,气体停留时间为14．47s时,BF,的去除率高达93．15％。     

电渗透脱水污泥干燥特性曲线及干燥模型

通过电渗透脱水技术及自然风干技术两种预处理方式降低污泥含水率,当污泥初始含水率相近时,研究经两种方式处理后污泥的干燥特性曲线,并对电渗透脱水污泥干燥特性曲线的优势情况进行探讨。在40—120℃的低温条件下,研究电渗透脱水污泥（泥饼厚度为3．5mm）的干燥特性曲线并分析其干燥特性。通过所得电渗透脱水污泥的干燥特性曲线,引人薄层污泥干燥模型进行数值分析。结果表明,在实验条件下,电渗透脱水污泥的干燥速率要优于自然风干污泥的干燥速率。随着温度的升高,电渗透脱水污泥的干燥速率随之升高,干燥到所需含水率的时间则随之减少。Logarithmic模型比其他模型更适合描述薄层电渗透脱水污泥在低温条件下的干燥特性。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

污泥膜覆盖好氧发酵堆体流场模拟及应用研究简

运用Gambit软件建立了污泥好氧发酵堆体的多孔介质模型,通过自行设计的实验装置获得了堆体的通风粘性阻力系数和惯性阻力系数以及功能膜压差与透气量之间的关系,用Fluent软件分析了堆体不同截面形状及底部通风管数量对堆体通风均匀性的影响,为确定合理的通风管数量及截面几何形状提供理论依据。对上海奉贤区城镇污水厂污泥处理工程发酵仓进行堆体流场模拟,确定堆体采用小拱形截面形状,堆高2 m,宽8 m,底部设置4条通风管,实际运行效果良好。     

水生植物酸碱预处理对厌氧发酵联产氢气-甲烷的影响简

采用酸碱预处理乌梁素海典型沉水植物龙须眼子菜和挺水植物芦苇,通过厌氧发酵动力学分析、还原糖变化及微观结构解析,研究酸碱预处理对水生植物厌氧发酵联产氢气-甲烷的影响。实验结果表明,酸碱预处理后水生植物厌氧发酵联产氢气-甲烷两阶段累积产气量、氢气及甲烷含量均显著提高,酸处理效果优于碱处理。采用0.5 mol/L HCl预处理龙须眼子菜效果最佳,最大氢气、甲烷含量分别达42.65%和52.82%,产氢气速率为4.118 mL/h,产甲烷速率最高达14.199 mL/h。芦苇经1 mol/L HCl预处理效果最佳,最高氢气、甲烷含量分别为32.22%和65.26%。扫描电镜微观结构分析表明,酸碱预处理可显著破坏芦苇、龙须眼子菜的纤维素结构,有效增加植物与微生物接触面积,有利于厌氧发酵联产氢气-甲烷工艺的快速启动和稳定运行。     

Levels and distribution of Dechloranes in sediments of Lake Taihu,China

The occurrence and spatial distribution of dechloranes including mirex, dechlorane plus (DP), dechlorane (Dec) 602, Dec 603, and Dec 604 in surficial sediments of Lake Taihu were investigated in this study. The concentrations of mirex and DP ranged from below detection limit (BDL) to 1.29 ng g^?1 dw and 0.051 to 2.10 ng g^?1 dw, respectively. Dec 602, Dec 603, and Dec 604 on the other hand, were BDL in any of the samples. The contamination levels of DP were higher than that of Mirex at 21 of all 22 sampling sites. Levels of mirex and DP in the lake sediments were correlated when an extremely high mirex value was removed. Both mirex and DP levels were correlated with the amount of organic matters in the sediment samples. Spatial distribution of mirex and DP suggested that these two chemicals in the lake had similar input sources except for one site. Comparison to previously reported flame retardants’ levels in the sediments shows that DP levels were similar with the levels of tetrabromobisphenol A, hexabromocyclododecane but lower than PBDEs and organophosphates levels in Lake Taihu. The higher levels in the north-east part of Lake Taihu adjacent to two major cities: Wuxi and Suzhou, indicated that city effluent might be a major source for DP contamination in the lake.     

隔膜压滤机滤室最优空腔厚度

利用UG软件对隔膜压滤机滤室内流体进行三维建模,导入Gambit中进行网格划分及边界条件的设定,结合Fluent选用RNG k-ε湍流模型,采用多孔介质模型模拟隔膜压滤机滤室内固-液两相流分离,得到不同空腔厚度下滤室内流体的体积分数轮廓图、压强云图,得出滤饼含水率与空腔厚度大小的关系。实验结果表明,模拟和实验结果具有较好的一致性。在压滤机滤室空腔厚度为12 mm时,滤饼含水率为48%,每天污泥处理量为102 t,隔膜压滤机工作效率最高。     

强化垂直流可渗透反应墙处理渗滤液污染物

针对垃圾渗滤液污染物组分多、处理难度大、可生化性差的特点,基于可渗透反应墙(PRB)被动修复技术,通过多种填料的组合构建三重垂直流PRB强化的砂箱模型,对垃圾渗滤液进行连续动态处理研究。实验结果表明,填料的组合顺序对强化PRB系统净化能力有较大的影响,由无烟煤、沸石、钢渣依次组成的强化垂直流PRB系统(2#砂箱)对NH+4-N、NO-3-N、NO-2-N、COD、PO3-4-P的平均去除率分别为96.12%、30.36%、75.24%、39.03%和30.47%,处理效果明显好于相同条件下依次由无烟煤、钢渣、沸石组成的强化垂直流PRB系统(1#砂箱)。与常规PRB处理系统相比,强化垂直流可渗透反应墙系统可实现垃圾渗滤液中多种污染物同步有效去除,是极具发展潜力的新型技术。     

Kinetics of peanut shell pyrolysis and hydrolysis in subcritical water

Biomass is recognized as an important solution to energy and the environmental problems related to fossil fuel usage. The rational utilization of biomass waste is important not only for the prevention of environmental issues, but also for the effective utilization of natural resources. Pyrolysis and hyrolysis in subcritical water are promising processes for biomass waste conversion. This paper deals with hydrolysis and pyrolysis of peanut shells. Hydrolysis and pyrolysis kinetics of peanut shell wastes were investigated for the in-depth exploration of process mechanisms and for the control of the reactions. Hydrolysis kinetics was conducted in a temperature range of 180–240 °C. A simplified kinetic model to describe the hydrolysis of peanut shells was proposed. Hydrolysis activation energy as well as the pre-exponential factor was determined according to the model. The target products of peanut shell hydrolysis, reducing sugars, can reach up to 40.5 % (maximum yield) at 220 °C and 180 s. Pyrolysis characteristics were investigated. The results showed that three stages appeared in this thermal degradation process. Kinetic parameters in terms of apparent pyrolysis activation energy and pre-exponential factor were obtained by the Coats–Redfern method.     

The fate and risk of selected pharmaceutical and personal care products in wastewater treatment plants and a pilot-scale multistage constructed wetland system

The removal of 12 pharmaceuticals and personal care products (PPCPs) in two full-scale wastewater treatment plants (WWTPs) and a tertiary treatment system was studied. The ecological risks of effluents from both secondary and tertiary treatment systems as well as excess sludge were evaluated. Primary treatment and ultraviolet light disinfection showed limited ability to remove most selected PPCPs. The combination of an anaerobic process and triple-oxidation ditches can eliminate DEET better than the anaerobic/anoxic/oxic process. Adsorption to sludge played a key role in the removal of triclocarban. Multistage constructed wetlands as a tertiary treatment efficiently removed caffeine and ibuprofen from wastewater and could decrease the risk of partial selected PPCPs. Selected PPCPs residues in excess sludge generally produced higher risks to the ecological environment than effluents from WWTPs.