Safety assessment of the film boiling chemical vapor infiltration (FB-CVI) process through a system-theoretic accident model and process (STAMP)

Film boiling chemical vapor infiltration (FB-CVI) is considered as one of the fastest process methodologies for manufacturing carbon-carbon (C–C) composite products and possesses various advantages compared to conventional methodologies. However, there are safety concerns associated with this process for large-scale manufacturing, mainly owing to the intrinsic nature of the precursor and the process conditions. Considering the multifunctional interactions of the various systems during the process, a system-theoretic process analysis (STPA)/system theoretic accident model and process (STAMP) model is used to perform a safety analysis of the hazardous states of the FB-CVI process at the system level. As a case study, the FB-CVI process equipment employed for the manufacturing of C–C composites is considered. The safety constraints present in the system are assessed for adequacy through a hazard analysis by STPA/STAMP. The analysis through STPA/STAMP demonstrated the capability to create proactive strategies for the design and realization of process equipment that can be employed to manufacture C–C composite products through the FB-CVI process.     

Study on Assessing Economic Vulnerability of Small Island Regions

The main purpose of this study is to assess economic vulnerability of small island development regions as part of their sustainability constraints. By combining economic and environmental time series data, we assessed a composite index of economic vulnerability which is constructed from three exogenous variables, namely economic exposure, economic remoteness, and economic impact of environmental and natural disasters. We used the Amami Islands, Kagoshima Prefecture, Japan as the case studies for this paper.The results indicated that using a gross island products based valuation index, Kikaijima is the most vulnerable island in the Amami Islands with a composite economic vulnerability index (CEVI) value of 0.678, while by using a per capita based index, Okinoerabujima is considered the most vulnerable island with a CEVI value of 0.680. From the results we also revealed that smaller islands have relative higher vulnerability than the bigger one, which also confirms some previous country-level vulnerability studies.However, it is matter of fact that some islands that have relatively high vulnerability also have good economic performance as shown by their per capita income. In this regard, it can be argued that the success of these small islands could have been achieved in spite of and not because of their inherent vulnerability conditions as an indicator of sustainability constraint. Regarding these findings, we also examined a comparison between vulnerability results and the preliminary concept of an island's resilience in order to capture another perspective on sustainability assessment in a small island region.     

包装箱用碳纤维增强复合材料贮存寿命研究

目的研究碳纤维增强复合材料贮存条件下的性能变化趋势和寿命评估。方法对碳纤维增强复合材料开展四个不同温度条件下的热氧老化试验,按试验周期定期取样开展冲击性能测试,对试验数据采用寿命预估方法进行处理,对材料性能进行预估。结果通过数据计算分别得到我国热带海洋、干热沙漠等典型气候条件下的碳纤维增强复合材料贮存寿命分别为17.21~35.89年。结论碳纤维增强复合材料具有较好的贮存性能,在较为严酷的热带海洋气候和给定的失效判据条件下,寿命预计为17.21年。试验和数据处理方法可以较好地预计材料的性能变化趋势和开展寿命评估。     

Morphology and electrical conductivity of PACS

ＩｎｔｒｏｄｕｃｔｉｏｎＰｏｌｙａｌｕｍｉｎｉｕｍｃｈｌｏｒｉｄｅ(ＰＡＣ) ,ａｋｉｎｄｏｆｉｎｏｒｇａｎｉｃｐｏｌｙｍｅｒｆｌｏｃｃｕｌａｎｔ,ｉｓｗｉｄｅｌｙｕｓｅｄｉｎｗａｔｅｒａｎｄｗａｓｔｅｗａｔｅｒｔｒｅａｔｍｅｎｔ.ＩｎｏｒｄｅｒｔｏｉｎｃｒｅａｓｅｔｈｅｃｏａｇｕｌａｔｉｏｎｅｆｆｅｃｔｏｆＰＡＣａｎｄｉｍｐｒｏｖｅｔｈｅｑｕａｌｉｔｙｏｆＰＡＣｐｒｏｄｕｃｔ,ｉｔｉｓｎｅｃｅｓｓａｒｙｔｏｒａｉｓｅｔｈｅｄｅｇｒｅｅｏｆｐｏｌｙｍｅｒｉｚａｔｉｏｎｏｆＰＡＣ .Ｇｅｎｅｒａｌｌｙ ,ｔ…     

混凝法在滇池蓝藻暴发期净水除藻的可行性研究

采用精制硫酸铝为混凝剂,L93^4正交法安排滇池蓝藻暴发期混凝沉降除藻除净水工艺实验。结果表明,混凝剂种类、水样pH值对蓝藻去除率有很大影响。研究确定了混凝剂除藻最佳操作条件,为混凝法去除蓝藻的工业化提供了理论和实际操作依据。     

活性硅酸聚合硫酸铁的研究

以硅酸钠，硫酸和聚合硫酸铁为原料制备活性硅酸合硫酸铁，测定了ＡＳＰＦＳ红外光谱，了Ｆｅ／Ｓｉ摩尔比和水样ＰＨ值等因素对产品和除浊效果的影响当Ｆｅ／Ｓｉ摩尔比为１．５时产品稳定性和除浊效果均较好。     

海水环境下玻璃纤维增强复合材料力学性能演化规律研究

目的 研究海水环境下海流能发电机组叶片用玻璃纤维复合材料力学性能的变化规律.方法 在实验室内通过海水浸泡试验、拉伸试验、弯曲试验以及剪切试验,测定叶片用玻璃纤维树脂基复合材料的吸水特性,以及在人工海水介质中各项力学性能参数的演变规律.结果 随着浸泡时间的增加,玻璃纤维树脂基复合材料吸水率先逐步增大、后趋于稳定,总吸水率约0.075％.抗拉强度呈先降低、后提高、又降低的趋势,抗拉强度最高可超过1100 MPa,最小值约为940 MPa.弹性模量和弯曲强度呈逐渐降低的趋势,弹性模量降幅约9.5％,弯曲强度降幅约为30％.弯曲模量变化起伏不定,变化幅度在15％以内.材料剪切强度呈先增大、后降低的趋势,最小值为189 MPa,较初始值高10 MPa.剪切模量呈先降低、后提高的现象,在浸泡28 d时,剪切模量最小,为16.4 GPa.结论 玻璃纤维增强树脂基复合材料经过长期海水浸泡后,拉伸及抗剪切性能略有降低,但降幅不大,抗弯性能下降明显,需要在叶片结构设计和强度计算时,充分考虑抗弯性能衰减的负面影响.     

Preparation of PFS coagulant by sectionalized reactor

The oxidation rate of ferrous sulfate is investigated for the preparation of polyferric sulfate(PFS)coagulant.In is proved that this reaction is zero order with respect to Fe^2 ,first order with respect to NO2(g),and first order with respect to the interface area between gas phase and liquid phase.According to this mechanism,sectionalized reactor(SR) is used in place of traditional reactor(TR),and the liquid of reaction mixture is recycled by pump.As a result,not only the flow path of reaction liquid is prolonged,but also gas-liquid contact area enlarged,and the reaction distinctly accelerated,compared with traditional reactor.The effects of parameters including temperature,acidity and others on the reaction rate are also discussed.     

镀液循环流量对封闭循环电沉积Ni-SiC复合镀层的影响

目的 研究封闭式镀液循环装置中不同镀液循环流量对Ni-SiC复合镀层的影响规律,优化镀液循环流量参数.方法 以Q235管状工件为待镀基体,以添加SiC颗粒的改良瓦特镀液为母液,在自主研发的封闭式镀液循环电镀装置中以0.3、0.5、0.7 m3/h的镀液循环流量于管件内壁制备Ni-SiC复合镀层,通过SEM检测、XRD测试、硬度测试和摩擦磨损性能测试等手段,对各Ni-SiC复合镀层宏微观形貌、厚度、成分、结构、硬度和耐磨性进行分析研究.结果 在0.5 m3/h流量条件下,镀层厚度为32.98μm,SiC颗粒含量为15.37％,镀层晶粒尺寸和硬度分别为10.84 nm和704HK0.245,该条件下制备的Ni-SiC复合镀层具有最佳耐磨性,摩擦系数为0.41,体积磨损率仅2.83×10–5 mm3/Nm.结论 在不同镀液循环流量参数下,采用该封闭式循环电镀装置,均可制得均匀完整的Ni-SiC复合镀层.随镀液循环流量的升高,镀层厚度和SiC颗粒体积含量均降低,镀层颜色金属光泽增强,镀层晶粒尺寸先减小、后增大,镀层硬度则先升高、后降低.     

钢铁废水混凝处理试验研究

通过某钢铁公司废水处理研究试验,采用不同混凝剂和阴阳离子型聚丙烯酰胺(PAM)助凝剂,对不同时间段的废水进行混凝试验,确定最佳加药量和最佳混凝剂。试验表明,硫酸铝对油、全铁和COD等的去除率相对较高,且具有不需投加助凝剂PAM、适用性强等优点。