红外和热分析联用在化工产品研究中的应用

运用实例论述了红外光谱分析与热分析联用在化工产品的产品开发和检测方面的应用。     

一种基于纹理特征的主动红外烟雾识别方法

视频图像火灾探测技术因其探测效率高、响应速度快等优点而被广泛应用,但普通摄像机无法拍摄零照度(黑暗)甚至低照度环境下的烟雾图像。而火灾发生时往往先产生烟雾,若能实现火灾早期的烟气探测将有利于预防火灾规模的扩大和人员财产的损失。利用红外摄像机结合红外发射灯来成像以完成对火灾的探测,具体探测过程为:首先利用中值滤波去除原始灰度图像中的噪声;其次利用三帧差分法提取烟雾前景;然后通过Local Binary Patterns与灰度共生矩阵分别获取烟雾纹理的局部和统计特征;最后将烟雾纹理特征输入Fisher分类器以识别烟雾与非烟雾(如水汽、飞尘等),并及时发出报警信号。设计有无环境风和人为干扰环境下的烟雾与水汽试验,利用烟雾运动的不规则性与扩散性、图像的Gabor特征、LBP尺度验证所用纹理特征。结果表明,从分类正确率和响应时间看,在低照度环境下所用纹理特征优于其他烟雾特征法。另外,通过调节相机与火源之间的距离,可得到应用于实际工程的红外摄像机最佳安装距离。     

基于OP-FTIR技术的炼油装置VOCs排放量监测

随着挥发性有机物排污收费政策的逐步实施,快速准确地监测企业VOCs排放量已成为环保部门和企业共同面对的难题。介绍了开路式傅里叶变换红外光谱技术原理及优势,研究了质量通量模式VOCs排放量计算方法,并以300 m×300 m某装置区域为例,完成了现场红外光谱测量、气象数据采集、数据有效性分析和VOCs排放量计算。研究结果表明,开路红外光谱技术极大提高了VOCs排放数据采集效率和准确性,进一步计算得出该装置区域VOCs年排放量平均值为98.7 t,为企业开展VOCs排放量核算提供了参考。     

等离子体催化降解甲苯途径的原位红外研究

考察了在常温常压条件下,等离子体分别协同SiO₂、Al₂O₃、NiO/Al₂O₃降解甲苯的性能,并从材料的介电常数、对甲苯的吸附性及臭氧分解能力等角度分析了不同活性表现的原因,同时,采用原位红外技术研究了甲苯降解过程中催化剂表面吸附物种的变化.结果表明,当甲苯浓度为100 ppm,气体流量为100 mL·min^-1时,一定范围内,甲苯降解率随着能量密度、介电常数、吸附性及臭氧分解能力的提高而提高.甲苯在催化剂表面的吸附对其降解途径有十分重要的影响:在放电区域中加入SiO₂,甲苯仍然在气相中完成降解;而存在Al₂O₃ 及NiO/Al₂O₃时,甲苯氧化成苯甲酸的过程主要发生在催化剂表面,是甲苯催化降解的关键步骤,苯甲酸在活性位点的积累将降低催化剂的反应活性.     

Degradation of direct azo dye by Cucurbita pepo free and immobilized peroxidase

Enzymatic decolourization of the azo dye, Direct Yellow (DY106) by Cucurbita pepo (courgette) peroxidase (CP) is a complex process, which is greatly affected by pH, temperature, enzyme activity and the concentrations of H₂O₂ and dye. Courgette peroxidase was extracted and its performance was evaluated by using the free-CP (FCP) and immobilized-CP (ICP) forms in the decolourization of DY106. Immobilization of peroxidase in calcium alginate beads was performed according to a strategy aiming to minimize enzyme leakage and keep its activity at a maximum value by optimizing sodium alginate content, enzyme loading and calcium chloride concentration. The initial conditions at which the highest DY106 decolourization yield was obtained were found at pH 2, temperature 20℃, H₂O₂ dose 1 mmol/L (FCP) and 100 mmol/L (ICP). The highest decolourization rates were obtained for dye concentrations 50 mg/L (FCP) and 80 mg/L (ICP). Under optimal conditions, the FCP was able to decolorize more than 87% of the dye within 2 min. While with ICP, the decolourization yield was 75% within 15 min. The decolourization and removal of DY106 was proved by UV-Vis analysis. Fourier transform infrared (FT-IR) spectroscopy analysis was also performed on DY106 and enzymatic treatment precipitated byproduct.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

光纤光栅测温技术在变压器测温中的应用

简要介绍了光纤光栅测温技术,以及在变电站主变温度测量的应用情况。     

固相萃取-红外分光光度法测定水中的总油

建立了固相萃取(SPE)-红外分光光度测定水中总油的方法,并对固相萃取条件进行了优化,实验表明,对于1L添加2mg标准油的水样,其总油的回收率为86%-93%,多次重复实验测定的相对标准偏差为2.9%(n=6)。     

红外系统对点源目标作用距离的优化计算

作用距离是红外系统核心性能指标之一,受大气、背景等多方面因素的影响。针对传统作用距离计算方法存在的局限,综合考虑多个影响因素,提出了一种优化计算方法,首次精确计算了作用距离与实际距离之差的大气衰减值,并对计算方法进行了验证。结果表明,优化计算方法具有较好的计算精度,可用于红外系统性能预测和整体设计。     

ε-聚赖氨酸生产废菌体对六价铬吸附影响的研究

以ε-聚赖氨酸(ε-PL)发酵生产废菌体小白链霉菌(Streptomyces albulus)PD-1为研究对象,探讨了其对吸附Cr(Ⅵ)的影响.实验过程中,对预处理方式、pH、初始Cr(Ⅵ)浓度、吸附时间和温度等因素进行了考察.结果表明,HCl预处理的菌体具有较好的吸附能力,Cr(Ⅵ)的吸附增加率达到22.7%,最佳pH为2.0左右,温度对Cr(Ⅵ)的吸附影响不大.实验过程中分别采取Langmuir和Freundlich 2种吸附等温模型对实验数据进行了拟合,得到2个模型的线性相关系数R2分别为0.979 4和0.979 8,这表明吸附过程中既存在单层吸附同时也存在复杂的多层吸附,小白链霉菌对Cr(Ⅵ)的最大理论吸附量为23.92mg.g-1.通过傅里叶变换红外光谱分析,酰胺基和羟基等基团在吸附过程中起主要作用.