西湖水体中铁铝钙镁的环境行为探讨

研究西湖水中铁，铝，钙，镁的含量分布，水平方向的动态交换，以及在引物水期与非引水期的变化，探讨这些元素在西湖水体自净中的作用。     

粉煤灰的综合利用

根据国内外文献资料周开，综述了粉煤灰在建材，、筑路、提取铝盐、烟气净化和工业废水处理等领域的综合利用现状和发展趋势。     

聚合氯化铝与聚磷硫酸铁絮凝除藻比较研究

针对武汉市莲花湖湖水,采用聚合氯化铝(PAC)和聚磷硫酸铁(PPFS)进行絮凝实验,比较了两种无机絮凝剂的絮凝效果及原水处理前后藻类群落变化。主要结论如下:①PPFS与PAC的最佳投加量分别为1.5mg/L、2.0mg/L;②PPFS在去除藻类细胞、浊度和色度方面均优于PAC,当PPFS投加过量时,因水体中Fe3+过量分布,使水样色度去除率下降;③PPFS絮凝处理微囊藻为主体的水华原水时,其效果比PAC更好。本文研究后表明:PPFS是一种新型高效絮凝剂,其絮凝性能明显优于PAC,当水体以微型藻类为主时,可使用PPFS以替代PAC,能提高絮凝效果。     

铝—溴邻苯三酚红—乙基紫—明胶显色体系的研究及应用

探讨了在明胶存在下，铝-溴邻苯三酚红（简称BPR）-乙基紫（简称EV）体系产生的协同显色反应条件。结果表明，在pH4．2～5．2的HAc－NaAc缓冲介质中，铝与BPR－EV形成离子型缔合物的最大吸收峰在615nm处，摩尔吸光系数为4．05×104L·mol-1·cm-1，铝含量在0～10μg／25ml遵循比耳定律．方法选择性好，可用于茶叶和铝锅沸水中铝含量分析，结果令人满意．     

Deposition behavior of residual aluminum in drinking water distribution system: Effect of aluminum speciation

Finished drinking water usually contains some residual aluminum.The deposition of residual aluminum in distribution systems and potential release back to the drinking water could significantly influence the water quality at consumer taps.A preliminary analysis of aluminum content in cast iron pipe corrosion scales and loose deposits demonstrated that aluminum deposition on distribution pipe surfaces could be excessive for water treated by aluminum coagulants including polyaluminum chloride（PACl）.In this work,the deposition features of different aluminum species in PACl were investigated by simulated coil-pipe test,batch reactor test and quartz crystal microbalance with dissipation monitoring.The deposition amount of non-polymeric aluminum species was the least,and its deposition layer was soft and hydrated,which indicated the possible formation of amorphous Al（OH）₃.Al₁₃ had the highest deposition tendency,and the deposition layer was rigid and much less hydrated,which indicated that the deposited aluminum might possess regular structure and self-aggregation of Al₁₃could be the main deposition mechanism.While for Al₃₀,its deposition was relatively slower and deposited aluminum amount was relatively less compared with Al₁₃.However,the total deposited mass of Al₃₀ was much higher than that of Al₁₃,which was attributed to the deposition of particulate aluminum matters with much higher hydration state.Compared with stationary condition,stirring could significantly enhance the deposition process,while the effect of pH on deposition was relatively weak in the near neutral range of 6.7 to 8.7.     

Nickel recovery from electronic waste II Electrodeposition of Ni and Ni–Fe alloys from diluted sulfate solutions

This study focuses on the electrodeposition of Ni and Ni–Fe alloys from synthetic solutions similar to those obtained by the dissolution of electron gun (an electrical component of cathode ray tubes) waste. The influence of various parameters (pH, electrolyte composition, Ni²⁺/Fe²⁺ ratio, current density) on the electrodeposition process was investigated. Scanning electron microscopy (SEM) and X-ray fluorescence analysis (XRFA) were used to provide information about the obtained deposits’ thickness, morphology, and elemental composition. By controlling the experimental parameters, the composition of the Ni–Fe alloys can be tailored towards specific applications. Complementarily, the differences in the nucleation mechanisms for Ni, Fe and Ni–Fe deposition from sulfate solutions have been evaluated and discussed using cyclic voltammetry and potential step chronoamperometry. The obtained results suggest a progressive nucleation mechanism for Ni, while for Fe and Ni–Fe, the obtained data points are best fitted to an instantaneous nucleation model.     

Uptake of aluminum by lipid vesicles

Aluminium uptake and tight binding were studied in multilayered phospholipid liposomes, as a model for cellular uptake of aluminum ions. Most of these studies were conducted with an initial aluminum concentration of 10 μM, while aluminum superficially bound to liposomes was removed by citrate chelation. Maximum uptake and tight binding of aluminium were pH‐dependent. In dimyristoyl phosphatidylcholine (DMPC) liposomes, this maximum occurred in the neutral pH region, while it was shifted towards more acidic pH values in DMPC liposomes containing 20% of acidic phosphatidylserine. The initial rate of aluminum uptake was apparently dependent on the physical state of the liposome membrane. Prior formation of an aluminum‐citrate chelate prevented aluminum uptake and tight binding to DMPC liposomes.     

Regimes and critical conditions of detonation propagation in expanding channels in gas suspensions of ultrafine aluminum particles

Under study are the regimes of detonation propagation in channels with linear expansion filled with monodisperse mixtures of oxygen and ultrafine aluminum particles of various loading; the methods of numerical simulations are used. The detonation combustion of submicron aluminum particles is described within the semi-empirical model of reduced kinetics with due regard to the transition from the diffusion-limited regime of combustion to the kinetic one. Waves of both planar and developed cellular detonation are considered as initial conditions. The characteristics of the main flow regimes are obtained and described: the subcritical (detonation failure), critical (detonation failure in some part of the channel) and supercritical (continuous detonation propagation). The maps of flow regimes in suspensions of 200-nm – 400-nm particles are presented in the plane of parameters: the channel width, expansion angle. The obtained critical conditions are similar to those observed in the gas detonation. The critical channel width linearly depends on the expansion angle up to a first critical value (35°–38°). Behind the second critical value (50°), the channel width is independent on the expansion angle. Between these values, there is an interval of nonmonotonicity similar to the detonation of micro-sized suspensions of aluminum particles. The effect of particle loading on the critical conditions in poor mixtures appears in the form of a sharp increase in the critical channel width, if the mass concentration falls below 0.25.     

Twin-roll casting of aluminum–steel clad strips

The results of experiments on twin-roll casting of aluminum–steel clad strips are presented. For the first time this energy-saving production technology for a clad material of this metals combination was implemented. Besides the experimental equipment and processing details, the results of metallographic, electron microprobe and transmission electron microscopy analysis of the aluminum–steel interface are shown. The pack rolling and deep-drawing tests of the twin-roll cast clad strips were performed to check their applicability for a further processing using plastic deformation. In addition adhesive strength of the bond was tested. The performed analysis have shown the formation of a continuous, thin and uniform layer of intermetallic phases on the materials interface of approx. 3 μm thickness having an adhesive strength over 70 MPa.     

Modeling methods for managing raw material compositional uncertainty in alloy production

Operational uncertainties create disincentives for use of recycled materials in metal alloy production. One that greatly influences remelter batch optimization is variation in the raw material composition, particularly for secondary materials. Currently, to accommodate compositional variation, firms commonly set production targets well inside the window of compositional specification required for performance reasons. Window narrowing, while effective, does not make use of statistical sampling data, leading to sub-optimal usage of recycled materials. This paper explores the use of a chance-constrained optimization method, which allows explicit consideration of statistical information on composition. The framework and a case study of cast and wrought production with available scrap materials are presented. Results show that it is possible to increase the use of recycled material without compromising the likelihood of batch errors, when using this method compared to conventional window narrowing. This benefit of the chance-constrained method grows with increase in compositional uncertainty and is driven by scrap portfolio diversification.