重庆市大气污染对锌材料腐蚀的经济损失分析

简要介绍了材料大气腐蚀经济损失的估算方法,并以2002年为基准年,选择了重庆市主城中心的6个功能区作为代表性区域,运用腐蚀破坏剂量响应函数和使用寿命计算公式对锌材料的腐蚀经济损失进行了定量估算.结果表明,由大气污染腐蚀破坏锌材料造成的年直接经济损失约为4061.7万元,约为同期GDP的0.1%.其中,干沉降对经济损失总量的贡献率在71%～99%之间,均值为92%.     

柔性散粒材料静力及动力学性能实验研究

战场环境下单兵防常规炸弹爆炸抗震减震技术装备及器材,由于受经费投入、战场环境等因素影响,一直没有成功研制并得到装备.通过室内砂箱振动台震动模拟试验,测试了不同柔性散粒材料在震动条件下的加速度值,对其减震性能作了一些初步的探讨.通过研究,可以看到柔性散粒材料在隔震方面具有其他材料所不具有的优越性能,可以作为制造隔震器材的首选.     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

Effective EU and Member State policies for stimulating CCS

Although CO₂ capture and storage (CCS) is widely recognised as an option to mitigate climate change, consistent and effective EU policies to advance CCS are still absent. This paper discusses policy instruments for advancing large-scale deployment of CCS in the European Union, and evaluates them in a multi-criteria analysis. The EU Emissions Trading Scheme (EU-ETS) is a cost-effective instrument for limiting greenhouse gas emissions, but it is questionable whether its currently limited time horizon and short-trading periods will lead to substantial CCS diffusion. Complementary policies at the EU and the Member State level may repair this and provide sufficient incentives for CCS. Potential policies include financial instruments such as investment subsidies, a feed-in scheme, or a CO₂ price guarantee, as well as a CCS mandate or a low-carbon portfolio. These policy options differ with respect to their environmental effectiveness, possible interaction with the EU-ETS, costs and financial risk involved, and their competition with other mitigation options. Interactions between Member State policies and the EU-ETS are smaller in scope than those of EU-wide policies, but they are more likely to lead to displacement of financial resources from other low-carbon technologies. In addition, national policies may pose a significant part of the financial risk of CCS operations with Member States, reducing the operator's incentive to innovate. Overall, structural policies at the EU level, such as a mandate or a low-carbon portfolio standard would be more conducive for realising large-scale deployment of CCS across the EU as well as more acceptable to environmental organisations.     

Assessing the economic feasibility of regional deep saline aquifer CO2 injection and storage: A geomechanics-based workflow applied to the Rose Run sandstone in Eastern Ohio, USA

Typical top-down regional assessments of CO₂ storage feasibility are sufficient for determining the maximum volumetric capacity of deep saline aquifers. However, they do not reflect the regional economic feasibility of storage. This is controlled, in part, by the number and type of injection wells that are necessary to achieve regional CO₂ storage goals. In contrast, the geomechanics-based assessment workflow that we present in this paper follows a bottom-up approach for evaluating regional deep saline aquifer CO₂ storage feasibility. The CO₂ storage capacity of an aquifer is a function of its porous volume as well as its CO₂ injectivity. For a saline aquifer to be considered feasible in this assessment it must be able to store a specified amount of CO₂ at a reasonable cost per ton of CO₂. The proposed assessment workflow has seven steps that include (1) defining the storage project and goals, (2) characterizing the geology and developing a geomechanical model of the aquifer, (3) constructing 3D aquifer models, (4) simulating CO₂ injection, (5,6) evaluating CO₂ injection and storage feasibility (with and without injection well stimulation), and (7) determining whether it is economically feasible to proceed with the storage project. The workflow was applied to a case study of the Rose Run sandstone aquifer in the Eastern Ohio River Valley, USA. We found that it is feasible in this region to inject 113 Mt CO₂/year for 30 years at an associated well cost of less than US $1.31/t CO₂, but only if injectivity enhancement techniques such as hydraulic fracturing and injection induced micro-seismicity are implemented.     

油气集输站安全监控预警及管理信息系统的开发

提出油气集输站安全监控预警及管理信息系统建设的调研内容、需求分析以及安全相关控制系统的风险分析流程。设计了该系统建设的4层结构框架和拓扑图,深入研究了实时参数监控、分级报警与安全保护控制、智能诊断与预警、多媒体监控、安全生产管理信息子系统的主要开发内容和功能实现。     

确定压力容器安全系数原则

压力容器安全系数与材料参数紧密相关,确定材料许用应力值时,需要同时考虑材料抗拉强度和屈服强度更为合理;奥氏体不锈钢材料具有非常好的应变强化能力和韧性,为充分发挥奥氏体不锈钢材料优良性能,选取奥氏体不锈钢材料许用应力值时,需要特殊考虑。压力容器安全系数的选取建立在经验基础上,在保障压力容器安全性前提条件下,为节省材料和降低成本,随着理论研究深入和科学实验的进步,压力容器安全系数有所降低,这是科学设计和实用成功经验结合的结果。     

炭催化剂吸附剂标准物质的研制

本文介绍了炭催化剂吸附剂标准物质的研制过程。对标准物质的制备技术、均匀性检验、稳定性考察及定值和不确定度进行了逐项分析。采用活性炭浸渍、煅烧技术制得炭催化剂吸附剂标准物质。试验结果表明,该标准物质定值结果准确,均匀性、稳定性良好。铜含量的标准值为11．06％,扩展不确定度为0．13％。     

Carbon capture and storage-desirability from a risk management point of view

Environmental and safety risks related to carbon capture and storage concern leakages and accidental releases during transport and geological storage. Based on principles widely accepted in the EU and beyond in the discussion about the where’s and why’s of nuclear waste repositories, this paper discusses the desirability of carbon capture and storage from a risk management point of view, focusing on environmental risks on the global level (climate change). On this basis it is concluded that, if the key energy issue of coming generations, not just in Europe but all around the world, is not the abundance of fossil resources but rather an unacceptably high probability of global warming due to greenhouse gas emissions, then the solution should not include any massive hiding of the emissions but entirely focus on the avoidance based on improved technology in power plants and other industrial installations.     

广东省杨村华侨柑桔场土壤微量元素含量与分布的研究

采集并分析全场不同母质形成的有代表性的土壤样本142个.研究结果表明,各类土壤全B、Mo、Zn和Mn含量的平均值均低于全国平均值,全量Cu平均值高于全国平均值.有效B、Mo、Zn和Mn含量的平均值均低于临界值,有效Cu的平均值稍高于临界值;但66.7％的土样有效Cu含量低于临界值.硼、钼、锌和锰严重缺乏,铜多数缺乏.全场各类土壤的微量元素含量差异较大,各类土壤微量元素的垂直和水平分布特征不尽相同,尤其是垂直分布差异明显.从土壤微量元素的全量与母质的关系来看,以玄武岩、紫色砂页岩母质形成的土壤全量较高,砂砾岩母质形成的土壤全量中等,砂页岩和冲积物母质形成的土壤全量较低.