4A沸石去除水中Pb2＋的研究

在静态条件下,研究了4A沸石对废水中Pb2＋的吸附性能,并探讨了影响吸附的因素。实验表明：当温度为30℃,废水pH为5～6,0．01g4A沸石对100mg／LPb2＋溶液10mL吸附20min,Pb2＋的去除率可达到99％以上。在实验研究条件下,4A沸石对Pb2＋的吸附符合Langmuir和Freundlich等温吸附方程,相关系数为0．9819和0．9998。经计算,4A沸石对Pb2＋的饱和吸附量为125mg／g。4A沸石吸附水中Pb2＋达到吸附平衡的时间较短;溶液pH值的变化对吸附效果影响不显著;温度从室温略微升高,Pb2＋的去除率略有增大。吸附在4A沸石上的Pb“可回收利用,处理后的4A沸石可以再生,且重复使用性能较好。     

新型硅镁胶(MgO·2SiO_2)对模拟放射性废水中Co~(2+)的吸附性能

以泡花碱和氯化镁为原料合成出了一种新型硅镁胶(MgO·2SiO2)吸附材料,用傅里叶红外光谱仪对其进行了表征,并对模拟放射性废水中的Co2+进行吸附实验。结果表明,控制合成pH在10.50~11.00,可以得到目标硅镁胶(MgO·2SiO2),在460 cm-1处出现了较强的吸收峰,这是由Mg—O伸缩振动和Si—Mg—O弯曲振动引起。在500℃焙烧4h后,可以得到吸附性能良好的硅镁胶,随着溶液pH的升高,去除率增大,在pH为4~8时达到最大。25℃时,最大吸附量可达135.5 mg/g,吸附过程符合Langmuir等温吸附方程和准二级动力学方程。重复使用4次,对Co2+的吸附量仍然达到130 mg/g,说明硅镁胶是一种可重复利用的吸附剂。     

膜电解技术处理含氯及重金属的废酸

采用离子交换膜电解技术处理铜冶炼过程产生的含氯及重金属的废酸。考察了废酸处理工艺、电解温度、电解时间、电流密度和催化剂的添加等条件对处理效果的影响。实验结果表明：采用先沉淀重金属后脱氯的废酸处理工艺,氯离子和铜离子的去除效果均较好;当以钛盐为催化剂时,在电解温度为40 ℃、电解时间为2.0 h、电流密度为825 A/m²的最佳工艺条件下,处理后废酸中的氯离子质量浓度为0.22 g/L,氯离子去除率为98.59%,铜离子质量浓度为0.45 g/L,铜离子去除率为95.08%,其他重金属大部分也得到有效去除。净化后的废酸可回用至铜冶炼的生产过程中。     

表面活性剂改性4A分子筛对Cr(VI)的吸附行为

采用浸渍法对4A分子筛进行表面改性,通过引入阳离子表面活性剂,使4A分子筛表面附着季铵型阳离子,并与反离子Br-形成"阴离子交换膜",从而促使更多的Cr(VI)阴离子通过离子交换吸附到改性4A分子筛上,通过X-射线衍射(XRD)和傅里叶变换红外光谱(FTIR)对样品的物相结构和组成进行表征分析。研究表明,表面活性剂的类型和疏水碳氢链结构会影响4A分子筛的吸附能力,十八烷基三甲基溴化铵(OTAB)碳氢链长,在分子筛表面形成的双分子层密,对Cr(VI)的吸附量最大。采用准一级、准二级、Elovich和Bangham动力学模型对六价铬的吸附数据进行拟合,其中准一级动力学方程最符合十八烷基三甲基溴化铵改性分子筛的吸附行为。同时,分别从Langmuir和Redlich-Peterson等温吸附模型获得六价铬的最大吸附量为13.98 mg/g,且改性分子筛以均一表面吸附为主。     

电除尘器电源交流分量对PM_(2.5)等细微颗粒物除尘效率的影响

除尘器对颗粒物的除尘效率与颗粒物的荷电量密切相关,PM2.5等细小颗粒物由于其荷电量不足而导致其吸收效率较低,对环境造成危害。为了增加粒子的荷电量,以粒子荷电原理为理论依据,从离子电流密度和通过电凝并扩大尘粒中位径2个方面研究了电除尘电源中交流电压分量对PM2.5等细小颗粒物荷电特性的影响,得出了电除尘器电源中交流电压分量可从以上2个方面提高装置对PM2.5等微小颗粒物的荷电量,且频率越高,幅值越大,荷电效果越好,从而可以提高装置对细小颗粒物的除尘效率。     

Development of a hybrid microbial fuel cell (MFC) and fuel cell (FC) system for improved cathodic efficiency and sustainability: the M2FC reactor

In an effort to improve the efficiency and sustainability of microbial fuel cell (MFC) technology, a novel MFC reactor, the M2FC, was constructed by combining a ferric-based MFC with a ferrous-based fuel cell (FC). In this M2FC reactor, ferric ion, the catholyte in the MFC component, is regenerated by the FC system with the generation of additional electricity. When the MFC component was operated separately, the electricity generation was maintained for only 98 h due to the depletion of ferric ion in the catholyte. In combination with the fuel cell, however, the production of power was sustained because ferric ion was continually replenished from ferrous ion in the FC component. Moreover, the regeneration process of ferric ion by the FC produced additional energy. The M2FC reactor yielded a power density of up to 2 W m⁻² (or time-averaged value of approximately 650 mW m⁻²), density up to 20 times (or approximately six times based on time-averaged value) higher than the corresponding MFC system.     

Novel mesoporous microspheres of Al and Ni doped LMO spinels and their performance as cathodes in secondary lithium ion batteries

A facile, scalable, and solution-based technique is used to fabricate Al and Ni-doped (LiAl_0.1Mn_1.9O₄ and LiAl_0.1Ni_0.1Mn_1.8O₄) microspheres of lithium manganese oxide (LMO) spinels for use as reversible cathode materials for lithium ion batteries (LIBs). The spheres of the two samples exhibit different porosities. Cells with these LMO-based cathodes are then cycled between 4.5 V and 2 V to study their stabilities while simultaneously being subjected to the undesirable Jahn-Teller distortion that occurs around the ~3 V regime. The LiAl_0.1Mn_1.9O₄ (LAMO) and the LiAl_0.1Ni_0.1Mn_1.8O₄ (LANMO) cells exhibit comparable open circuit voltages (OCV) of 2.94 V and 2.97 V, respectively. During cell cycling, the LAMO cell exhibits a maximum specific capacity of 122.51 mAh g^?1 with a capacity fade of 65.35% after 75 cycles. The LiAl_0.1Ni_0.1Mn_1.8O₄ (LAMO) sample fares better and exhibits a maximum of 140.49 mAh g^?1 and a capacity drop of 52.59%. Detailed structural studies indicate that Ni doping and the greater degree of porosity of the LANMO sample to be a stabilizing factor. This is further confirmed by cyclic voltammetry (CV) and AC impedance spectra analysis.     

Widespread waterborne pollution in central Swedish lakes and the Baltic Sea from pre-industrial mining and metallurgy

Metal pollution is viewed as a modern problem that began in the 19th century and accelerated through the 20th century; however, in many parts of the globe this view is wrong. Here, we studied past waterborne metal pollution in lake sediments from the Bergslagen region in central Sweden, one of many historically important mining regions in Europe. With a focus on lead (including isotopes), we trace mining impacts from a local scale, through a 120-km-long river system draining into Mälaren - Sweden's third largest lake, and finally also the Baltic Sea. Comparison of sediment and peat records shows that pollution from Swedish mining was largely waterborne and that atmospheric deposition was dominated by long-range transport from other regions. Swedish ore lead is detectable from the 10th century, but the greatest impact occurred during the 16th-18th centuries with improvements occurring over recent centuries, i.e., historical pollution > modern industrial pollution.     

Cd-tolerant Suillus luteus: A fungal insurance for pines exposed to Cd

Soil metal pollution can trigger evolutionary adaptation in soil-borne organisms. An in vitro screening test showed cadmium adaptation in populations of Suillus luteus (L.: Fr.) Roussel, an ectomycorrhizal fungus of pine trees. Cadmium stress was subsequently investigated in Scots pine (Pinus sylvestris L.) seedlings inoculated with a Cd-tolerant S. luteus, isolated from a heavy metal contaminated site, and compared to plants inoculated with a Cd-sensitive isolate from a non-polluted area. A dose-response experiment with mycorrhizal pines showed better plant protection by a Cd-adapted fungus: more fungal biomass and a higher nutrient uptake at high Cd exposure. In addition, less Cd was transferred to aboveground plant parts. Because of the key role of the ectomycorrhizal symbiosis for tree fitness, the evolution of Cd tolerance in an ectomycorrhizal partner such as S. luteus can be of major importance for the establishment of pine forests on Cd-contaminated soils.     

碱激发胶凝材料及其固化Pb^2＋的试验研究

对碱激胶凝材料（碱-偏高岭土、碱-矿渣和碱-粉煤灰）与水-水泥体系固化Ph^2＋进行了试验研究,其中水-水泥体系为对比样。结果表明：对于相同稠度的碱激发胶凝材料,即使Pb^2＋含量达到2．4％,除了碱-粉煤灰的抗压强度略低外,其他都达到30MPa以上,满足填埋或做建筑基材的使用要求;与水泥相比,碱激发胶凝材料能显著降低重金属离子（Ph^2＋）浸出浓度,其规律性与其NH4交换容量大小的规律性一致,与其固化体的抗压强度的大小没有相关性。