穿层爆破中控制孔对裂隙扩展作用机理试验研究

为研究控制孔在穿层爆破中对裂隙扩展的作用机理,在实验室内进行穿层爆破相似模拟试验。研究表明:煤岩体试块上表面产生了贯穿炮孔和控制孔的裂隙,侧面生成了多条不规则的裂隙,试块内部出现了包括沿控制孔方向发展的多个断裂面;炮孔和控制孔连线上产生了较高拉应力,炮孔和控制孔连线方向上拉应变峰值是炮孔45°方向上的拉应变峰值的1.12倍;爆破产生的压缩应力波P和在控制孔处反射生成的反射横波Sr、反射纵波Pr在控制孔附近的煤岩体上产生应力叠加,造成煤岩体损伤,最终形成贯穿裂隙。穿层爆破中控制孔对爆生裂隙的扩展起到导向作用,但由于穿层爆破中煤岩交界面的存在,使得应力波出现复杂的反射、透射、叠加效应,造成煤层内裂隙无序发育,工程现场应予以重视。     

浅谈爆破振动的控制措施

结合爆破振动的作用机理,分别对减少振源爆炸能量、干扰降振、阻断振动波传播途径、控制爆破规模、合理选择分段间隔时间等爆破振动主要控制措施进行了分析讨论。并根据实际施工情况分析了通过电子雷管实现干扰降振的减振效果,为类似工程提供借鉴作用。     

露天矿山隐伏盲空区精确探测及爆破优化设计

隐伏盲空区是严重威胁露天矿山正常采矿作业的安全隐患,应予以探明并处置。针对露天矿隐伏盲空区探测难度大、崩落处置爆破设计精度差等问题,以白马铁矿1号溜井盲空区为例,首先基于矿山历史资料,利用钻探手段,初步圈定盲空区异常分布范围;然后运用钻孔激光扫描设备进行三维精确扫描,获得盲空区塌腔三维形态和真实边界,并以实测数据为基础,利用逆向建模方法,构建盲空区三维可视化模型;最后根据盲空区的三维空间特征和分布条件,进行爆破分区及参数优化设计。结果表明:采用钻探圈定结合三维激光精确扫描建模的综合探测方法,可获得露天矿山盲空区的可靠信息,准确掌握盲空区垮塌现状,进而为制定更为精准的爆破设计方案提供重要依据,最终达到消除盲空区的目的。研究结果对保障矿山安全生产具有重要意义,同时可为类似工程提供有益参考。     

空区隐患爆破治理方案及延期时间的数值模拟分析

为了防止矿山空区引起地表塌陷造成建构（筑）物的破坏以及降低矿柱塌落振动对井下开采的威胁,采用现场试验与数值模拟相结合的方法,优选爆破治理方案和延期时间。根据炮孔布置和爆破参数,建立实际比例数值模型;在岩石物理力学指标测试的基础上,确定模型材料参数;采用LS-DYNA数值模拟软件,对比分析方案优劣以及确定爆破延期时间。研究结果表明:在满足空区隐患爆破治理效果的前提下,同一节点处A方案质点振速峰值为0.923 9 m/s小于B方案质点振速峰值1.225 3 m/s;而且当延期时间为100 ms时,通过模型垂直方向的位移云图可知岩石的破坏范围最大,塌落区域更加分散。现场应用结果显示空区隐患治理工程爆破效果良好,形成了隔离缓冲层,可以保证露天和井下的安全。     

不同地应力条件下直眼掏槽破岩的理论研究与数值模拟

为了研究不同地应力场对直眼掏槽破岩的影响,提出了基于Schwarz交替迭代法和弹性力学理论建立的掏槽区岩体的应力状态方程,同时对不同地应力条件下单孔直眼掏槽破岩过程进行了数值模拟。结果表明:在炸药爆炸前期和中期,初始地应力场对结果影响较小,主要是槽孔爆炸应力场起主导作用,在爆炸后期,初始地应力场对爆破后裂纹的扩展具有导向作用,裂纹扩展主方向趋向于最大初始地应力方向。进一步分析表明,岩体在初始地应力场与爆炸应力场共同作用后,在空孔和槽孔圆心连线上产生最大拉应力,并且在不同地应力条件下最大拉应力模拟值的发展趋势与理论计算较为一致。     

长庆油田4731B型非金属集输管道老化特性实验研究

为推广非金属复合管在油田集输油领域的应用,明确其在集输环境中的老化特性是关键问题。基于集输油现场的工程条件,针对长庆油田试用的4731B型钢丝缠绕增强复合管,以采出原油、采出水为实验介质,通过挂片实验、水压爆破实验,借助电镜扫描、拉伸测试对复合管内衬层老化行为、拉伸性能以及复合管极限承压与老化特性进行研究。结果表明:采出原油与采出水均可渗透扩散进入内衬层内部,还会发生局部深入渗透;采出原油、采出水的局部渗透速率分别可达3.4,10.6 mm/a;在某些工况下,内衬层表面产生裂纹;短时间（168 h）内的介质渗透甚至裂纹对其机械性能影响较小,而光氧老化影响显著;现场服役813 d后,复合管极限承压下降2.79%,表明复合管承压性能稳定。     

Emissions of organophosphate and brominated flame retardants from selected consumer products and building materials

The emissions of selected flame retardants were measured in 1- and 0.02-m³ emission test chambers and 0.001-m³ emission test cells. Four product groups were of interest: insulating materials, assembly foam, upholstery/mattresses, and electronics equipment. The experiments were performed under constant environmental conditions (23°C, 50% RH) using a fixed sample surface area and controlled air flow rates. Tris (2-chloro-isopropyl)phosphate (TCPP) was observed to be one of the most commonly emitted organophosphate flame retardants in polyurethane foam applications. Depending on the sample type, area-specific emission rates (SER_a) of TCPP varied between 20 ng m⁻² h⁻¹ and 140 μg m⁻² h⁻¹.The emissions from electronic devices were measured at 60°C to simulate operating conditions. Under these conditions, unit specific emission rates (SER_u) of organophosphates were determined to be 10–85 ng unit⁻¹ h⁻¹. Increasing the temperature increased the emission of several flame retardants by up to a factor of 500. The results presented in this paper indicate that emissions of several brominated and organophosphate flame retardants are measurable. Polybrominated diphenylethers exhibited an SER_a of between 0.2 and 6.6 ng m⁻² h⁻¹ and an SER_u of between 0.6 and 14.2 ng unit⁻¹ h⁻¹. Because of sink effects, i.e., sorption to chamber components, the emission test chambers and cells used in this study have limited utility for substances low vapour pressures, especially the highly brominated compounds; hexabromocyclododecane had an SER_a of between 0.1 and 29 ng m⁻² h⁻¹ and decabromodiphenylether was not detectable at all.     

Time course of isocyanate emission from curing polyurethane adhesives

The time course of isocyanate emission from curing polyurethane (PUR) resins and adhesives was studied in two different emission test chambers. The measured emissions were strongly dependent on the type of experiment. The adhesives under investigation contained different types of diisocyanates and are used for different applications, e.g. for fixing of textile floor coverings. The influence of the curing mechanism on emission was studied by comparing the emission curves of one-component adhesives (OCA) and two-component adhesives (TCA). For TCA, the decrease in isocyanate emission was found to follow a two-step process during curing. In the first step, the emission is dominated by surface evaporation, and the decay of emission is mainly caused by the decrease in monomer content due to reaction. In the second step, the release is limited by internal diffusion. The influence of monomer reactivity on the emission profile could be demonstrated for 2,4′- and 4,4′-MDI. The less-reactive 2,4′-MDI caused prolonged emission. A strong dependence of emission rates on temperature and adhesive viscosity was also obvious. The evaluation of emission rates of different commercially available PUR adhesives showed the highest emission from systems that are applied at high temperatures. The high reactivity of diisocyanates requires special techniques for sampling and analysis. Therefore, an analytical method using HPLC–MS/MS was developed that enables limits of quantitation of <5 ng/m³ with a sampling volume of 100 l.     

A new environmental chamber for evaluation of gas-phase chemical mechanisms and secondary aerosol formation

A new state-of-the-art indoor environmental chamber facility for the study of atmospheric processes leading to the formation of ozone and secondary organic aerosol (SOA) has been constructed and characterized. The chamber is designed for atmospheric chemical mechanism evaluation at low reactant concentrations under well-controlled environmental conditions. It consists of two collapsible 90 m³ FEP Teflon film reactors on pressure-controlled moveable frameworks inside a temperature-controlled enclosure flushed with purified air. Solar radiation is simulated with either a 200 kW Argon arc lamp or multiple blacklamps. Results of initial characterization experiments, all carried out at 300–305 K under dry conditions, concerning NO_x and formaldehyde offgasing, radical sources, particle loss rates, and background PM formation are described. Results of initial single organic–NO_x and simplified ambient surrogate–NO_x experiments to demonstrate the utility of the facility for mechanism evaluation under low NO_x conditions are summarized and compared with the predictions of the SAPRC-99 chemical mechanism. Overall, the results of the initial characterization and evaluation indicate that this new environmental chamber can provide high quality mechanism evaluation data for experiments with NO_x levels as low as 2 ppb, though the results indicate some problems with the gas-phase mechanism that need further study. Initial evaluation experiments for SOA formation, also carried out under dry conditions, indicate that the chamber can provide high quality secondary aerosol formation data at relatively low hydrocarbon concentrations.     

CASTEX连续铸挤的侧向扩展挤压挤压力计算

以金属铅为坯料进行侧向扩展挤压模拟CASTEX机的径向扩展挤压.由变形流动规律建立简化力学模型推导挤压力计算公式并进行验证.