我国废钢铁加工设备生产使用现状及前景展望

对我国2009年粗钢产量及废钢铁加工供应情况进行概述和预测,介绍了我国废钢铁加工设备的生产规模、使用状况及研发现状,以及我国废钢铁加工设备的种类及其性能。展望了我国废钢铁加工设备的前景,指出质优价廉、适合中国国情、具有环保功能的废钢铁加工设备市场发展空间巨大。     

无缝钢管局部径向模具塑性成形过程的三维有限元数值模拟

采用大变形弹塑性有限元理论,用DYNA3D(研究版)有限元软件,对无缝钢管局部径向模具塑性成形过程中当凸模的凹槽尺寸与凸模的圆弧半径发生变化时进行了数值模拟研究,得出了对成形钢管表面质量控制具有重要参考价值的结论,解决了成形钢管表面的压痕问题。     

熔池高度对双辊薄带凝固组织影响的模拟预测

在已建立的理论数学模型的基础上,以1Cr18Ni9Ti不锈钢为研究对象,模拟预测了薄带厚度保持不变条件下熔池高度对薄带凝固组织的影响。研究结果表明:随着熔池高度增加,1Cr18Ni9Ti不锈钢双辊薄带凝固组织中柱状晶区比例首先增大,然后又逐渐减小。而柱状枝晶取向度和枝晶间距则随着熔池高度的增加而增大,但在较低的熔池高度条件下,柱状枝晶间距在凝固结束时有突然增大的趋势。     

Detecting neural tube defects by amniocentesis between 11 and 15 weeks' gestation

Forty-two open neural tube defects (NTDs) were identified in our series of 7440 amniocenteses tested between 11 and 15 weeks of gestation. Using a cut-off of ≥2.0 MOM, the detection rate for open NTDs was 95 per cent; 100 per cent each for anencephaly and spina bifida; and 78 per cent for encephalocele. Two encephaloceles had AFP levels less than 2.0 MOM and negative AChEs. Thirty-four (81 per cent) of these NTDs were tested between 13 and 15 weeks and 8 (19 per cent) before 13 weeks. There were 0.6 per cent false positives by AFP (excluding serious abnormalities and fetal death) and 0.1 per cent after AChE. The likelihood of an open NTD after an elevated AFP (≥2.0 MOM) was 24 and 77 per cent for any serious abnormality. These results, when combined with an earlier study, indicate that amniotic fluid AFP appears to be as sensitive a test for open NTDs between 13 and 15 weeks as between 16 and 20 weeks. Additional experience is necessary to determine this before 13 weeks.     

检测管法与纳氏试剂光度法测定氨氮的比较研究

对氨氮真空玻璃检测管法和纳氏试剂光度法进行检出限、精密度、准确度,以及实际样品测试方面的比较研究。研究表明,氨氮检测管的检出限为0．2mg／L,精密度测定的相对标准偏差为0％～5．75％,准确度测定的加标回收率为93％～124％。检测管法和纳氏剂法同时测定多种实际样品,结果两种方法的相对误差为-37．8％～11．8％,结论：检测管法能够满足半定量测试的需求。     

海水淡化水在既有管网输配的铁释放控制研究

由于具有强腐蚀性,海水淡化水在既有市政管网输配过程中往往会产生严重的"红水"现象,主要是由于管网中铁的释放.为了研究控制既有管网中铁释放的有效措施,对管龄为30～40 a的钢管和灰口铸铁管内壁的腐蚀瘤进行分析,主要组成物质为Fe3O4和FeOOH;选择腐蚀较严重的钢管进行静态浸泡试验,重点分析了自来水和淡化水的掺混比、pH值、碱度、氯离子和硫酸根离子对铁释放的影响,并以铁浓度为控制量,初步给出了海水淡化水在既有管网中安全输配所需满足的水质条件:自来水和淡化水的掺混比≥2∶1,pH值在7.6以上,碱度>200 mg.L-1.     

Multi-process and multi-pollutant control technology for ultra-low emissions in the iron and steel industry

The iron and steel industry is not only an important foundation of the national economy, but also the largest source of industrial air pollution. Due to the current status of emissions in the iron and steel industry, ultra-low pollutant emission control technology has been researched and developed. Liquid-phase proportion control technology has been developed for magnesian fluxed pellets, and a blast furnace smelting demonstration project has been established to use a high proportion of fluxed pellets (80%) for the first time in China to realize source emission reduction of SO₂ and NO_x. Based on the characteristics of high NO_x concentrations and the coexistence of multiple pollutants in coke oven flue gas, low-NO_x combustion coupled with multi-pollutant cooperative control technology with activated carbon was developed to achieve efficient removal of multiple pollutants and resource utilization of sulfur. Based on the characteristics of co-existing multiple pollutants in pellet flue gas, selective non-catalytic reduction (SNCR) coupled with ozone oxidation and spray drying adsorption (SDA) was developed, which significantly reduces the operating cost of the system. In the light of the high humidity and high alkalinity in flue gas, filter materials with high humidity resistance and corrosion resistance were manufactured, and an integrated pre-charged bag dust collector device was developed, which realized ultra-low emission of fine particles and reduced filtration resistance and energy consumption in the system. Through source emission reduction, process control and end-treatment technologies, five demonstration projects were built, providing a full set of technical solutions for ultra-low emissions of dust, SO₂, NO_x, SO₃, mercury and other pollutants, and offering technical support for the green development of the iron and steel industry.     

内螺纹变截面铜管拉伸工艺的研究

此文提出了内螺纹变截面铜管分段拉仲一次成形新工艺,并就工艺因素对该管拉伸成形的影响进行了试验研究,从而为合理制订成形工艺提供了依据。     

钢铁行业节能技术潜力与成本分析—以长三角地区为例

钢铁行业是能源消耗和碳排放的重点行业,节能减排是钢铁行业绿色低碳转型发展的有效途径,节能技术是钢铁行业提高能源效率、降低碳排放和减少空气污染的关键。运用节能供给曲线方法对长三角地区钢铁行业技术节能成本进行评价,并对2030年长三角地区钢铁行业技术节能潜力进行评估。结果表明：钢铁行业28项技术在2030年预计为长三角地区累计节能875.74 PJ,约为2020年长三角地区钢铁行业总能耗的34%;考虑不同收益项时的技术节能成本存在差异,当不考虑任何收益时技术的节能成本最高,当将协同效益纳入考虑后,技术的节能成本降到较低水平;贴现率、温室气体或污染物交易价格等因素会对技术的节能成本产生影响,贴现率越高意味着资金成本越高,技术的节能成本也相应越高;温室气体或污染物价格上升会增加技术节能的收益,从而降低技术的节能成本。

     

开口圆管非对称弯曲的一种方法

开口圆管非对称弯曲时,在尺寸、形状均有较高精度要求的情况下弯曲有一定的难度。此文介绍了一种成功的开口圆管非对称弯曲冷态成形方法。