最大剪切模量对土动力参数及地震反应的影响

最大剪切模量是影响土的动剪切模量比、阻尼比和土层地震反应的最重要参数之一。通常采用室内应变法来确定最大剪切模量，给出土的动剪切模量比和阻尼比，而采用现场剪切波速法求得的结果则很少见。研究了剪切波速法和应变法所确定的最大剪切模量对土动剪切模量比、阻尼比和土层地震反应的影响，推导了两种方法所确定的动剪切模量比和阻尼比之间的关系式。结果表明：最大动剪切模量对土的动剪切模量比、阻尼比和土层地震反应的影响很显著。     

Post-explosion observations of experimental mine and laboratory coal dust explosions

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike 1 m³ chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.     

Determination of turbulent burning velocities of dust air mixtures with the open tube method

Correlating turbulent burning velocity to turbulence intensity and basic flame parameters-like laminar burning velocity for dust air mixtures is not only a scientific challenge but also of practical importance for the modelling of dust flame propagation in industrial facilities and choice of adequate safety strategy. The open tube method has been implemented to measure laminar and turbulent burning velocities at laboratory scale for turbulence intensities in the range of a few m/s. Special care has been given to the experimental technique so that a direct access to the desired parameters was possible minimising interpretation difficulties. In particular, the flame is propagating freely, the flame velocity is directly accessible by visualisation and the turbulence intensity is measured at the flame front during flame propagation with special aerodynamic probes. In the present paper, those achievements are briefly recalled. In addition, a complete set of experiments for diametrically opposed dusts, starch and aluminium, has been performed and is presented hereafter. The experimental data, measured for potato dust air mixtures seem to be in accordance with the Bray Gülder model in the range of 1.5 m/s<u′<3.5 m/s. For a further confirmation, the measurement range has been extended to lower levels of turbulence of u′<1.5 m/s. This could be achieved by changing the mode of preparation of the dust air mixture. In former tests, the particles have been injected into the tube from a pressurised dust reservoir; for the lower turbulence range, the particles have been inserted into the tube from above by means of a sieve–riddler system, and the turbulence generated from the pressurised gas reservoir as before. For higher levels of turbulence, aluminium air mixtures have been investigated using the particle injection mode with pressurised dust reservoir. Due to high burning rates much higher flame speeds than for potato dusts of up to 23 m/s have been obtained.     

Influence of the oxide content on the ignition energies of aluminium powders

Some results of determination of ignition energies for an aluminium powder with various oxide contents are presented. Common use of processes like high-speed cutting produce explosive dust clouds, so that we focused this study on hazard of metallic powders. An industrial aluminium powder has been used for this work. An original process, based on the principle of electrochemical anodisation, has been developed to increase, under control, the oxide coating of particles.

The sensitivity study to spark ignition was performed in an Hartmann explosion tube of 1.3L. The Langlie test method was applied to evaluate the energies leading to a probability of ignition of 50% (E₅₀) of the selected samples. The results confirm that the ignition energies increase with the oxide content of the powder.     

Moderation of dust explosions

Inherent safety is a proactive approach to process safety in which hazards are removed or minimized so as to reduce risk without engineered (add-on) or procedural intervention. Four basic principles are available to attain an inherently safer design—minimization, substitution, moderation, and simplification. The subject of the current paper is the principle of moderation as it applies to the prevention and mitigation of dust explosions.

Moderation can be achieved by processing a material under less severe operating conditions or by processing the material in a less hazardous form. With respect to the latter approach, it may be possible to alter the composition of a dust by admixture of solid inertants, or to increase the dust particle size so as to decrease its reactivity. Additionally, avoidance of the formation of hybrid mixtures of explosible dusts and flammable gases is an application of moderation of the material hazard.

Several examples are given for each of the above three forms of moderation. The discussion on admixture of solid inertants includes examples from the following industrial applications: (i) refractory materials manufacturing, (ii) food processing, (iii) power generation, (iv) industrial recycling, and (v) foundry shell mold fabrication. The importance of particle size consideration is explained first from the perspective of engineering tools such as the Dow Fire & Explosion Index, and professional guidance on the definition of a dust and suitable particle sizes for explosibility testing. Industrial examples are then drawn from the following areas: (i) rubber recycling and textile manufacturing, (ii) industrial recycling, (iii) wood processing, (iv) dry additive handling (polyethylene facility), (v) polyethylene production, (vi) carbon block recycling, and (vii) coal mining. The concluding discussion on hybrid mixtures includes brief cases from the process safety literature.     

Ignitability characteristics of aluminium and magnesium dusts that are generated during the shredding of post-consumer wastes

The authors investigated the ignitability of aluminium and magnesium dusts that are generated during the shredding of post-consumer waste. The relations between particle size and the minimum explosive concentration, the minimum ignition energy, the ignition temperature of the dust clouds, etc. the relation between of oxygen concentration and dust explosion, the effect of inert substances on dust explosion, etc. were studied experimentally.

The minimum explosive concentration increased exponentially with particle size. The minimum explosive concentrations of the sample dusts were about 170 g/m³ (aluminium: 0–8 μm) and 90 g/m³ (magnesium: 0–20 μm). The minimum ignition energy tended to increase with particle size. It was about 6 mJ for the aluminium samples and 4 mJ for the magnesium samples. The ignition temperature of dust clouds was about 750 °C for aluminium and about 520 °C for magnesium. The lowest concentrations of oxygen to produce a dust explosion were about 10% for aluminium and about 8% for magnesium. A large mixing ratio (more than about 50%) of calcium oxide or calcium carbonate was necessary to decrease the explosibility of magnesium dust. The experimental data obtained in the present investigation will be useful for evaluating the explosibility of aluminium and magnesium dusts generated in metal recycling operations and thus for enhancing the safety of recycling plants.     

钠盐量影响下DD6单晶高温合金的高温热腐蚀规律研究

目的 开展镍基单晶高温合金DD6在950 ℃下的热盐腐蚀试验(95%Na2SO4+5%NaCl)，探明涂盐量和涂盐方式(周期涂盐和单次涂盐)对DD6高温热腐蚀的影响规律和机理。方法 结合扫描电子显微镜、X射线能量色散谱、X射线衍射等设备，对不同涂盐量及涂盐方式下DD6的表面及横截面形貌进行观察分析，分析不同涂盐量和涂盐方式下DD6的高温热腐蚀机理。结果 DD6在950 ℃下主要发生碱性熔融热腐蚀，同时伴随氧化、硫化和氯化等过程。高温热腐蚀使得DD6合金表面生成的保护性氧化膜被熔融态的腐蚀介质破坏，导致O、S、Cl等外部元素通过氧化膜的缺陷进入DD6基体中，在合金的亚表面发生内氧化、内硫化以及内氯化反应，横截面上出现明显的腐蚀层，其主要由氧化物以及硫化物组成。随着热腐蚀的进行，DD6表面物质发生了剥蚀，沉积盐量的增加导致剥蚀现象越加严重，合金内部致密的组织结构也被破坏，横截面上出现了大量孔洞、裂纹等缺陷。在相同涂盐量下，周期涂盐法使得DD6的腐蚀程度高于单次涂盐法。结论 DD6高温热腐蚀行为与涂盐量及涂盐方式密切相关，相同涂盐方式下，涂盐量越大，DD6热腐蚀更加严重。涂盐量一定时，周期涂盐法使得DD6的热腐蚀剧烈程度大于单次涂盐法，且DD6在上述热腐蚀条件下均发生剥蚀破坏。     

卧式电除尘器电晕极优化实验研究

运用粉尘粒子荷电原理,对四种电晕极的主要技术性能进行了试验研究,探讨了卧式电除尘器的最佳极配形式。     

地矿部门坑道作业尘毒危害情况

对坑道中的尘毒进行了测试,并根据测试结果提出了一些建议。     

胶带输送机防尘治理综合改进措施

叙述了胶带输送机现有防尘罩的不足及改进措施。