Influence of concentration distribution of hydrogen in air on measured flammability limits

There is a clear difference between exiting data on the measured flammability limits of hydrogen-air mixture. The non-uniformity of concentration distribution of hydrogen in air is a contributor to deviations of the upper flammability limit (UFL) and the lower flammability limit (LFL) measured in different experiments. This paper presents a numerical model to simulate the gas mixing process from start to stability, to predict the concentration distribution, and to research the influence of concentration distribution of hydrogen in air on measured UFLs and LFLs. The commercial software package Fluent was used to carry out the numerical simulation for the concentration distribution of hydrogen in air in the vessels with length-to-diameter ratios (L: D) of 1:1, 3:1, 5:1 and 7:1 respectively. Based on the numerical simulation and analysis, the influence of concentration distribution on measured flammability limits was demonstrated for hydrogen in air in the vessel. It is found that the deviations of measured flammability limits of hydrogen in air are the minimum in the vessel with length-to-diameter ratio of 1:1, and augment with the augmentation of vessel length-to-diameter ratio. Moreover, it is presented that the deviations of measured flammability limits of hydrogen in the center of the vessel are lower than that in the top and the bottom.     

Development of the Spatial Rainfall Generator (SRGEN) for the Agricultural Policy/Environmental Extender Model

Accurate spatial representation of climatic patterns is often a challenge in modeling biophysical processes at the watershed scale, especially where the representation of a spatial gradient in rainfall is not sufficiently captured by the number of weather stations. The spatial rainfall generator (SRGEN) is developed as an extension of the “weather generator” (WXGEN), a component of the Agricultural Policy/Environmental eXtender (APEX) model. SRGEN generates spatially distributed daily rainfall using monthly weather statistics available at multiple locations in a watershed. The spatial rainfall generator as incorporated in APEX is tested on the Cowhouse watershed (1,178 km²) in central Texas. The watershed presented a significant spatial rainfall gradient of 2.9 mm/km in the lateral (north‐south) directions based on four rainfall gages. A comparative analysis between SRGEN and WXGEN indicates that SRGEN performs well (PBIAS = 2.40%). Good results were obtained from APEX for streamflow (NSE = 0.99, PBIAS = 8.34%) and NO₃‐N and soluble P loads (PBIAS ≈ 6.00% for each, respectively). However, APEX underpredicted sediment yield and organic N and P loads (PBIAS: 24.75‐27.90%) with SRGEN, although its uncertainty in output was lower than WXGEN results (PBIAS: ?13.02 to ?46.13%). The overall improvement achieved in rainfall generation by SRGEN is demonstrated to be effective in the improving model performance on flow and water quality output.     

Auto-adaptive Air Distribution and Structure Optimization of Ejector Burner for Biomass Alcohol Fuels

A plenty of studies on the utilization of biomass alcohol fuels have been conducted, but combustion efficiency and stability of this fuels still need to be improved. Based on biomass alcohol fuels (bio-methanol and bio-ethanol), this paper studied auto-adaptive air distribution characteristics and optimum structure parameters of an ejector burner by numerical simulation method. Also, an experiment was conducted to verify the numerical results. The results show that the mole air entrainment ratio (MAER) keeps almost constant when the ejector fuel nozzle exit locates at the segment between the ejector throat and the suction chamber entrance, but a bigger ratio α would lead to a higher MAER till the α is bigger than 8.5 for bio-methanol and 11.5 for bio-ethanol. The bio-ethanol fuel is more beneficial for air carrying role because of its big molecular weight. Operation pressure (P_w) has a little impact on MAER of the two fuels, but the rise of back pressure (P_b) would lead to rapid decrease of MAER for the two fuels. For the optimum structure burners, the MAER can be maintained at the value of theoretical complete combustion. Its changing rate is less than 2.3% for bio-methanol and 2.5% for bio-ethanol when the burner load changes from 30% to 120%, which is highly consistent with the experimental results. The optimum burner can distribute air supply automatically with the changing of burner load.     

基于LCA的北京市公交车节能及温室气体减排潜力分析

新能源公交车是未来城市公交行业节能及温室气体减排的重点发展方向.新能源公交车在行驶阶段具有良好的节能及温室气体减排效果,而汽车制造、能源生产等相关生命周期阶段的能耗及温室气体排放常被忽视,且目前新能源公交车的乘客运载功能相对较弱,可能对节能及温室气体减排的潜力造成较为显著的影响.因此,本文基于北京市公交车的运营特征,采用生命周期评价(LCA)方法,选择客运周转量作为功能单位,核算了天然气公交车、混合动力公交车和纯电动公交车等新能源公交车相对于柴油公交车的节能及温室气体减排效益.结果表明:发展新能源公交车对促进北京市公交行业及城市节能低碳发展具有积极的作用,但相对于基于运营里程的核算结果,本研究新能源公交车节能及温室气体减排潜力均较低,主要原因是新能源公交车的实际载客量相对较低;混合动力公交车和纯电动公交车在空调开启时的节能潜力与温室气体减排潜力均远低于天然气公交车;通过发展情景分析,建议北京市现阶段应优先发展天然气公交车,适当发展纯电动公交车和混合动力公交车,以减少北京市公交车的总体能耗,同时降低温室气体排放强度.     

Experimental investigation of the efficiency of triple rinsing of agricultural containers regarding their characterization as non-hazardous wastes

The efficiency of water rinsing for removing fenthion from non-combustible used pesticide containers was investigated. Four hundred empty containers from four olive oil producing areas in Greece were studied. Following triple rinsing cleaning procedures, the amount of fenthion retained in the container ranged from 0.01% to 0.1% w/w of its initial concentration. Extraction was accomplished with acetone, and the extracts were analyzed with a capillary gas chromatographic system coupled with flame ionization detector. The results obtained showed that triple rinsing is an effective procedure for removing fenthion from used pesticide containers, since the remaining pesticide concentration was below the legislated threshold value. Consequently, the containers can be handled as non-hazardous solid wastes.     

胎盘内多环芳烃分布及源解析研究

探讨多环芳烃在胎盘中的分布,并对其进行源解析。从2012年6月—2013年6月在云南省第一人民医院产科分娩的产妇中随机抽取30例,利用气相色谱-质谱联用仪(GC-MS)检测其胎盘中多环芳烃的含量;比较胎盘的中央部分和边缘部分多环芳烃含量的差异;对多环芳烃进行源解析,探讨其主要来源。胎盘中检测到多种多环芳烃成分;其中2~4个苯环的多环芳烃占总量的90%以上,尤其是萘、苊、芴、菲、蒽、芘、荧蒽的含量较高;萘、苊烯、苊、茚并(1,2,3-c,d)芘、二苯并(a,h)蒽5种多环芳烃在胎盘中央的含量高于边缘,具有显著性差异(P0.05),其他多环芳烃在胎盘中央和边缘的含量无显著性差异(P0.05)。多环芳烃源解析提示80%研究对象体内的多环芳烃主要来自石油产品的燃烧或暴露于石油产品。     

应用概率物种敏感度分布法研究太湖重金属水生生物水质基准

目前广泛使用的水质基准推导方法—物种敏感度分布法存在曲线拟合模型不确定、曲线拟合效果不佳、种内差异欠考虑、基准值不准确等诸多问题,概率物种敏感度分布法可有效解决上述问题。应用概率物种敏感度分布法构建了太湖水体中5种重金属Ag、Pb、Cd、Hg和Zn的概率物种敏感度分布曲线,在此基础上得到了保护水生生物的急性水质基准分别为1.079μg·L~(-1)、637.973μg·L~(-1)、19.465μg·L~(-1)、8.729μg·L~(-1)和105.506μg·L~(-1),慢性水质基准分别为0.108μg·L~(-1)、63.797μg·L~(-1)、1.947μg·L~(-1)、2.340μg·L~(-1)和52.753μg·L~(-1);不同类群间生物对重金属的敏感度存在差异,不同重金属对同一类群生物的毒性也存在差异;通过与国内外已有的重金属水质基准值比较,发现水质基准具有明显的区域性,目前基于国外水质基准或我国整体水域特点来制定的太湖水质标准,往往造成对太湖水生生物欠保护或过保护的状况。     

PBDEs的来源特征、环境分布及污染控制

多溴联苯醚(Polybrominated diphenyl ethers,PBDEs)生产应用、环境分布与生态风险之间的关系将如何影响我国的未来,具体涉及到工业、环境、健康、人类繁衍等的社会问题.由于PBDEs阻燃效率高,热稳定性好,价格便宜,作为添加剂被广泛应用在电子、电器、化工、交通、建材、纺织、石油等领域的阻燃产品中.PBDEs进入环境后迁移扩散并富集于沉积物和生物体内,进入人体后引起肝脏毒性、内分泌干扰、神经毒性和生育能力下降等而危害人类的健康.基于此,从生产应用、品种生产量、分子的物理化学特性以及毒性等的文献数据分析了PBDEs的来源特征与环境危害,分析这些性质对环境分布与污染控制的基础支持关系;从沉积物、水体、大气、水生生物、人体5个方面考察了PBDEs的环境本底浓度变化、分配关系、迁移规律、时间效应,分析了生产、应用与扩散的多因素影响关系,发现全球性PBDEs污染物蔓延的现象,沉积物是主要的归趋场所,室内空气中的浓度远高于室外,水中浓度较低,水生生物和人体均能富集PBDEs,通过饮食、母乳和呼吸摄入,可实现代际传播,污染的分布呈现介质与区域的不同特征;污染控制需要考虑点源技术与面源修复的联合,结合PBDEs的物理性质、分子结构及其化学特性,统计分析了微生物法、光化学降解法和零价铁还原法的原理及其有效性,根据PBDEs在产品中存在与分布的特点,提出收集-分离-富集-超临界催化还原和氧化毁毒的工艺,针对实际环境(以电子垃圾塑料和流域水体及沉积物为对象)中的PBDEs进行回收或处理,结合材料如催化剂的应用,从动力学和热力学方面提高PBDEs无害化的效率.最后,从生产管理、环境监测、风险评价、技术集成等方面提出了未来的努力方向.     

管道中烟道气流动传热及酸凝结规律

针对注烟道气稠油热采中管道输送烟道气酸凝结问题,以连续性方程、能量方程和动量方程为基础建立了烟道气沿管道流动与传热计算模型,计算了烟道气沿管道的压力分布、温度分布和酸凝结点距离,分析了不同入口参数和烟道气成分对管道中烟道气的压力、温度、酸凝结点的影响。结果表明:SO3或水蒸汽含量增加时,烟道气酸凝结点温度提高,凝结点距离减小;入口烟道气压力提高,烟道气压降变小,温降不变,酸凝结点距离减小;入口烟温升高,压降和温降都增大,酸凝结点距离增大;保温层厚度增加,温降减小,酸凝结点距离增大。计算和分析结果表明:减少烟道气中SO3或水蒸汽含量可以有效地增大酸凝结点距离,减轻管道腐蚀问题。     

Hg0 removal from flue gas over different zeolites modified by FeCl3

The elemental mercury removal abilities of three different zeolites (NaA, NaX, HZSM-5) impregnated with iron (III) chloride were studied on alab-scale fixed-bed reactor. X-ray diffraction, nitrogen adsorption porosimetry, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and temperature programmed desorption (TPD) analy-ses were used to investigate the physicochemical properties. Results indicated that the pore structure and active chloride species on the surface of the samples are the key factors for physisorption and oxidation of Hg⁰, respectively. Relatively high surface area and micropore volume are beneficial to efficient mercury adsorption. The active Cl species generated on the surface of the samples were effective oxidants able to convert elemental mercury (Hg⁰) into oxidized mercury (Hg²⁺). The crystallization of NaCl due to the ion exchange effect during the impregnation of NaA and NaX reduced the number of active Cl species on the surface, and restricted the physisorption of Hg⁰. Therefore, the Hg⁰ removal efficiencies of the samples were inhibited. The TPD analysis revealed that the species of mercury on the surface of FeCl₃-HZSM-5 was mainly in the form of mercuric chloride(HgCl₂), while on FeCl₃-NaX and FeCl₃-NaA it was mainly mercuri coxide(HgO).