南京理工大学高压实验室及其研制高压水射流切割机

南京理工大学高压实验室自８０年代初建立以来，在高压容器及武器发射管的自紧理论和工程应用、高压零部件研制、高压传感器和信号放大显示系统、高压介质等方面做了大量的工作。９３年以来，进行了水射流切割机的研制工作，解决了超高压缸体的动态密封、高压缸体的自增强、无触点式换向传感器、内衬不锈钢组合型高压容器等诸多问题，试制成功了水射流切割机样机。     

改性树脂NKZ对水溶性染料的吸附特性研究

根据聚合物絮凝剂与染料相互作用机理,用硝基胍对大孔型氯球改性得到了功能化吸附树脂NKZ.从热力学和动力学两方面研究了该树脂对5种水溶性染料的静态吸附特性.结果表明,树脂NKZ对水溶性染料的吸附具有很好的效果.     

垃圾场渗出污水厌氧处理的可行性研究

采用血清瓶静态试验法研究了垃圾渗出污水的厌氧处理的可行性。试验表明:垃圾渗出污水对厌氧发酵微生物无抑制作用,有良好的厌氧降解性,产气率为0.321/g·COD,污水中的大部份有机物都能被厌氧消化,COD_cr去除率为78.2%,发酵过程中还能获得能源——沼气。具有良好的应用前景。     

龙门式高压水射流快速洗消装置的研究

介绍了龙门式高压水射流快速洗消装置的系统组成、系统主要参数的确定,系统的工作过程;计算分析了系统水力特性、工作参数与应用。     

Predicting mass rapid transit noise levels on an elevated station

This study developed a noise prediction model for elevated mass rapid transit (MRT) platforms. Relevant physical and operational parameters (e.g. cruise speed, acceleration and deceleration rates for trains, building fa?ade setbacks and so on) were collected from the Bangkok mass transit system (BTS), the first elevated MRT system operated in Bangkok, Thailand. The equivalent continuous sound pressure levels (L(Aeq)) were collected from both sides of the MRT stations at the center of each platform. The relevant parameters were collected on both platforms and ground level, on both sides of MRT stations. These parameters were statistically tested to determine their correlation with MRT noise. The final model was built from highly correlated parameters using multiple regression analysis with a stepwise regression technique. Statistical evaluation showed a high degree of goodness-of-fit test for the model to the observed data. Therefore, it can be efficiently used for the projection of MRT noise in the affected areas.     

岩溶地基土洞塌陷评价及处理

地下水(地表水)产生的渗透潜蚀作用、崩解作用等是土洞形成和发展的重要原因。对工程实例中的土洞,采用极限平衡法和压力拱分析法进行了稳定性判别。在土洞中充填砼,然后采用压力灌浆,灌浆所采用的水灰比为1∶1~1∶1.5,灌浆压力一般为0.15~0.30 MPa,地基处理效果好。     

大型公共活动风险控制研究与分析

大型公共活动人口密度大、流动性强,极易引发安全事故,造成大量人员伤亡和恶劣社会影响。笔者从风险管理角度,提出大型公共活动的风险控制程序,通过方案评估、静态评估、管控能力及应急能力等几方面对大型公共活动进行动态分析。明确划分大型公共活动场所的重点部位;将大型公共活动的管控能力预警分为4个等级,界定相应人群容量特征,并针对不同级别提出相应安全管理措施;强调整体容量,重点部位容量的确定应与项目目标协同一致,形成大型公共活动风险管理控制的新思路,对大型公共活动风险管理具有重要意义,值得在一般大型公共活动风险评估中广泛应用。     

灰色层次结构模型在故障树分析中的应用

故障树分析技术对于复杂系统的故障诊断具有重要应用价值,提出把故障树看作2层灰色结构,通过建立灰色层次结构模型,给出判断各种故障模式发生可能性大小的一种通用方法.将其应用于压力容器爆炸事故的故障树分析,并取得了与实际情况吻合的满意结果.该方法为了解事故影响因素重要程度、控制事故发生和改进系统可靠性提供依据.     

Planar detonation structure for chain-branching kinetics with large activation energy and small initiation rate

The structure of the steady planar detonation wave is analyzed for three-step chain-branching kinetics consistent with hydrogen–air chemistry. The initiation and chain-branching steps are described by an Arrhenius rate. Both are thermally neutral, so that heat release is due to termination. The initiation rate is typically very low and very stiff. As a result, a small fraction of the reactant is consumed in the initiation region, which is very long but ends in an exponential chain-branching explosion. Next, the reactant is rapidly converted into chain-branching radicals, within a very thin zone, which ends when the concentration of the chain-branching radical reaches a peak, because of reactant depletion. Finally, the termination step consumes the chain-branching radicals and releases heat within a region thicker than the peak zone, but much thinner than the initiation region. The analysis is based upon two assumptions: that the chain-branching activation energy is high and that initiation is slow. The structure of the initiation and chain-branching zones is different for post-shock states within or outside the explosion region in the chain-branching diagram. In the former situation, chain-branching is already stronger than termination at the von Neumann point, and vice versa. In the no-explosion case, the initiation zone becomes very long, while the little chain-branching specie produced by initiation is directly converted into product by the termination step. Temperature increases slowly until reaching the explosion curve, when chain-branching becomes stronger than termination. The subsequent structure is similar to the explosion case.     

Disparity of a Seat Cushion and Its Influence on Postural Control

Properties of supporting surfaces of a seat have an influence on postural control. Centre of pressure (COP) displacement parameters reflect both the balance controlling process and movements of the centre of a mass of entire body. The subjects of the study were 9 healthy men. A seat cushion was examined with a 2-force platform setup. Force exertion at a seat pan and feet and COP displacement at a seat pan were measured to analyse postural control. Analysis of variance determined the differences in postural control depending on a cushion type among the subjects. Significant differences in COP displacement parameters were in COP trajectory length, medio-lateral COP displacement and COP velocity. The results of the study showed that foam cushion ensures better postural control.