钢渣掺量对泡沫混凝土砌块性能的影响

泡沫混凝土是一种环保、节能的保温隔热材料,以其优良的保温性能,受到越来越多研究者的关注。对钢渣的特性进行了分析测试,对钢渣不同掺量对泡沫混凝土砌块特性的影响进行了研究,结果表明,采用添加5％～35％钢渣所制备的钢渣泡沫混凝土砌块,其密度等级为JC／T1062—2007中的B10级,掺人5％、15％钢渣的泡沫混凝土抗压强度达到A3．5等级,掺人25％、35％钢渣的泡沫混凝土抗压强度达到A2．5等级。随着钢渣掺量的增大,抗压强度、抗折强度降低,吸水率增大。在同一钢渣掺量的情况下,泡沫混凝土砌块的抗压强度变化率增加显著,而且随着钢渣的加入量升高而增大。钢渣的加入有利于提高泡沫混凝土砌块的后期抗压强度。     

PUF大气被动采样技术对POPs的采样计算

随着《斯德哥尔摩公约》的实施,大气中持久性有机污染物(POPs)的大气被动采样(PAS)观测技术得到了快速发展,相比于传统大气主动采样技术,PAS技术具有明显的优势。以应用最为广泛的聚氨酯软性泡沫材料大气被动采样(PUF-PAS)为例,重点阐述和讨论了3种通过大气被动采样技术来计算污染物在空气中的浓度的方法,并对其采样原理和发展趋势进行了简要介绍。     

Ring-Opening Polymerization of Cyclic Esters onto Liquefied Biomass

Ring-opening polymerization of cyclic esters (-caprolactone, -valerolactone, and l-lactide) onto liquefied biomass (LB) was conducted to obtain the polyester-type polyol and to regulate the characteristics of LB. IR and ¹H-NMR spectra of the obtained polyol showed that the polymerization was successfully conducted in the presence of acid catalyst, which is used in liquefaction. The molecular weight (M_w), hydroxyl value, and viscosity were controllable by changing the reaction conditions. Polyester-type polyurethane foams with a wide range of properties were prepared from the obtained polyol with the appropriate combinations of foaming agents.     

Disparity of a Seat Cushion and Its Influence on Postural Control

Properties of supporting surfaces of a seat have an influence on postural control. Centre of pressure (COP) displacement parameters reflect both the balance controlling process and movements of the centre of a mass of entire body. The subjects of the study were 9 healthy men. A seat cushion was examined with a 2-force platform setup. Force exertion at a seat pan and feet and COP displacement at a seat pan were measured to analyse postural control. Analysis of variance determined the differences in postural control depending on a cushion type among the subjects. Significant differences in COP displacement parameters were in COP trajectory length, medio-lateral COP displacement and COP velocity. The results of the study showed that foam cushion ensures better postural control.     

Electrochemical remediation of copper (II) from an industrial effluent Part II: three-dimensional foam electrodes

A batch recycle removal of copper ions from an industrial effluent by means of copper foam cathodes was tested. A constant current of 750 A was applied to the cell in order to perform the reduction. Copper depletion was investigated at different solution flow rates and a removal greater than 98% was obtained with a flow rate of 1000 l/h. The influence of initial metal concentration on copper deposition and current efficiency is also discussed.     

压缩空气泡沫在长距离管路输送中压降的数值模拟

基于Fluent对压缩空气泡沫在长距离管道中的流动特性进行了数值模拟研究,将压缩空气泡沫近似为弥散流,采用Saplart-Allmaras模型模拟了不同管径下压缩空气泡沫以及不同泡沫原液浓度的AFFF泡沫在长距离管道内的流动及压降变化。模拟结果表明,随着距离变化,各管径管道内压降均呈现线性变化,且随着压缩空气泡沫的流动,压降线性增大。管道管径对管内压降变化具有显著影响,管道直径越小,管道内压降越大;泡沫原液浓度对压降的影响较小,且压缩空气泡沫在长距离输送中的压力随距离线性衰减。将模拟结果与长距离输送的试验结果进行了对比,误差在10%以内。     

不同载体材料对厌氧氨氧化效果影响的研究

文章分别采用水性聚氨酯(WPU)和活性炭2种材料作为生物载体,在2个不同的上流式厌氧污泥床(UASB)反应器中接种包埋污泥和生物活性炭,采用人工配水进行连续实验,观测厌氧氨氧化反应器启动过程中各种含氮化合物的变化,以考察不同载体材料对厌氧氨氧化过程的影响。文章在生物活性炭反应器中成功驯化了采自污水处理厂的普通厌氧污泥,证明了从环境中驯化培养厌氧氨氧化菌的可能性。通过2个阶段中脱氮效率的比较,发现以水性聚氨酯包埋材料作为未驯化细菌载体并无明显优势,反而成为传质的障碍;而采用生物活性炭则可以迅速达到提高局部生物量、聚集功能菌、屏蔽不利环境的干扰等作用,是理想的微生物载体。     

外浮顶储罐泡沫灭火设施的选型

分析了外浮顶储罐火灾危险性及火灾类型,对目前泡沫灭火设施在外浮顶储罐中的应用及存在的问题进行阐述,建议外浮顶储罐的泡沫灭火设施采用边缘泡沫消防系统.     

聚氨酯泡沫固定化产碱杆菌细胞生物转化氰化物

利用1株产碱杆菌DN25作为降氰菌株,以聚氨酯泡沫为载体进行固定化,研究其转化特性.结果表明,采用吸附生长法能有效实现菌株DN25的固定,固定细胞量可达到每g泡沫载体生物量干重0.35g.固定化细胞的最适转化温度和pH为35℃、8.0.对于低浓度氰化物,固定化细胞和游离细胞的转化速率相当;对于高浓度氰化物,固定化细胞具有明显优势,不仅可耐受更高浓度的氰化物转化,其转化速率也高于游离细胞,最大转化速率为507mg/(L·h),是游离细胞的2.8倍.通过初步的摇瓶模拟序列批式反应,固定化细胞活性可保持20d.     

煤矿综掘面泡沫降尘技术研究与实施

针对煤矿综掘面粉尘治理技术中存在的不足,采用泡沫降尘新技术结合长压短抽式通风方式进行粉尘防治。以霍尔辛赫矿为例,根据井下实际情况,利用GAMB IT和FLUENT建立掘进巷道的几何模型,并对巷道掘进通风过程中粉尘分布规律进行解算,将模拟结果和现场实测数据对比,确定掘进面回风侧的高浓度粉尘分布区。对掘进面煤样进行湿润性试验,确定最佳的发泡剂添加比例。综合以上情况,泡沫降尘技术实施时采用环形前置式喷头布置,发泡剂添加比例定为10‰,并在回风侧距掘进面5 m、距底板2 m处设置风筒,将高浓度粉尘抽出并沉降。现场实测数据显示,泡沫降尘技术降尘效率明显高于喷雾降尘技术。使用泡沫降尘时,在司机侧测得全尘及呼吸性粉尘降尘效率分别达到75.4%和74.7%。