Validation of a QuEChERS-based gas chromatographic method for analysis of pesticide residues in Cassia angustifolia (senna)

A simple multi-residue method based on modified QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) approach was established for the determination of 17 organochlorine (OC), 15 organophosphorous (OP) and 7 synthetic pyrethroid (SP) pesticides in an economically important medicinal plant of India, Senna (Cassia angustifolia), by gas chromatography coupled to electron capture and flame thermionic detectors (GC/ECD/FTD) and confirmation of residues was done on gas chromatograph coupled with mass spectrometry (GC-MS). The developed method was validated by testing the following parameters: linearity, limit of detection (LOD), limit of quantification (LOQ), matrix effect, accuracy–precision and measurement uncertainty; the validation study clearly demonstrated the suitability of the method for its intended application. All pesticides showed good linearity in the range 0.01–1.0 μg mL^?1 for OCs and OPs and 0.05–2.5 μg mL^?1 for SPs with correlation coefficients higher than 0.98. The method gave good recoveries for most of the pesticides (70–120%) with intra-day and inter-day precision < 20% in most of the cases. The limits of detection varied from 0.003 to 0.03 mg kg^?1, and the LOQs were determined as 0.01-0.049 mg kg^?1. The expanded uncertainties were <30%, which was distinctively less than a maximum default value of ±50%. The proposed method was successfully applied to determine pesticide residues in 12 commercial market samples obtained from different locations in India.     

扩散荷电作用下线板式ESP中PM2.5捕集效率的数值模拟

为考察线板式静电除尘器中PM2.5颗粒的除尘性能,建立电场、颗粒动力场和流场多场耦合下的数学理论模型.采用GAMBIT软件构造ESP实体结构,将用户自定义程序UDF导入到FLUENT软件中进行数值仿真,并应用DeutsehAnderson公式计算粉尘在不同荷电机理和2种不同除尘操作参数下的除尘效率.数值结果表明,扩散荷电效应对PM2.5分级除尘效率贡献率随粒径增大非线性减小;外加工作电压越低或烟道气流速越高,扩散荷电效应对PM2.5粉尘颗粒的影响越大;在较高外加电压工况下,扩散荷电对综合效率的影响与降低一定量的烟道气流速相当.     

Development of controlled release formulations of imidacloprid employing novel nano-ranged amphiphilic polymers

Amphiphilic copolymers, synthesized from poly (ethylene glycols) and various aliphatic diacids, which self assemble into nano-micellar aggregates in aqueous media, were used to develop controlled release (CR) formulations of imidacloprid [1-(6 chloro-3-pyridinyl methyl)-N- nitro imidazolidin-2- ylideneamine] using encapsulation technique. High solubilisation power and low critical micelle concentration (CMC) of these amphiphilic polymers may increase the efficacy of formulations. Formulations were characterised by Infrared (IR) spectroscopy, Dynamic Light Scattering (DLS) and Transmission Electron Microscope (TEM). Encapsulation efficiency, loading capacity and stability after accelerated storage test of the developed formulations were checked. The kinetics of imidacloprid release in water from the different formulations was studied. Release from the commercial formulation was faster than the CR formulations. The diffusion exponent (n value) of imidacloprid, in water ranged from 0.22 to 0.37 in the tested formulations. While the time taken for release of 50 % of imidacloprid ranged from 2.32 to 9.31 days for the CR formulations. The developed CR formulations can be used for efficient pest management in different crops.     

Matrix diffusion coefficients in volcanic rocks at the Nevada test site: influence of matrix porosity, matrix permeability, and fracture coating minerals

Diffusion cell experiments were conducted to measure nonsorbing solute matrix diffusion coefficients in forty-seven different volcanic rock matrix samples from eight different locations (with multiple depth intervals represented at several locations) at the Nevada Test Site. The solutes used in the experiments included bromide, iodide, pentafluorobenzoate (PFBA), and tritiated water ((3)HHO). The porosity and saturated permeability of most of the diffusion cell samples were measured to evaluate the correlation of these two variables with tracer matrix diffusion coefficients divided by the free-water diffusion coefficient (D(m)/D*). To investigate the influence of fracture coating minerals on matrix diffusion, ten of the diffusion cells represented paired samples from the same depth interval in which one sample contained a fracture surface with mineral coatings and the other sample consisted of only pure matrix. The log of (D(m)/D*) was found to be positively correlated with both the matrix porosity and the log of matrix permeability. A multiple linear regression analysis indicated that both parameters contributed significantly to the regression at the 95% confidence level. However, the log of the matrix diffusion coefficient was more highly-correlated with the log of matrix permeability than with matrix porosity, which suggests that matrix diffusion coefficients, like matrix permeabilities, have a greater dependence on the interconnectedness of matrix porosity than on the matrix porosity itself. The regression equation for the volcanic rocks was found to provide satisfactory predictions of log(D(m)/D*) for other types of rocks with similar ranges of matrix porosity and permeability as the volcanic rocks, but it did a poorer job predicting log(D(m)/D*) for rocks with lower porosities and/or permeabilities. The presence of mineral coatings on fracture walls did not appear to have a significant effect on matrix diffusion in the ten paired diffusion cell experiments.     

Characterization of an urban landfill soil by using physicochemical analysis and solid phase microextraction (SPME)—GC/MS

We have aimed at characterizing top soil samples taken in-situ from five different locations of the unregulated dumping site in Eskişehir/Turkey for a period of six months. The study is the first attempt in the city and in Turkey, regarding particularly the SPME (Solid Phase Microextraction Technique) analysis method utilized. A comprehensive research has been conducted to produce critical soil data to be used for indicating current risks as well as the urgency of rehabilitating the site and establishing a sanitary landfill in the site. Conventional physicochemical analytical methods and SPME technique were used to analyze the samples. Physicochemical analyses were performed for determining the pH, total dried matter, volatile matter, total nitrogen, phosphorus, macro elements and heavy metals. Meteorological data were also recorded for the same period. SPSS.10.0 statistical program was used to determine the correlation between meteorological data and physicochemical analysis results. Mean values were used in the correlation analyses. These data indicated that the air temperature and precipitation have significant effects on soil characteristics. SPME, coupled with GC/MS, was used to identify eighty six volatile and semi-volatile organic compounds contained in soil samples. The samples were extracted by headspace SPME with heating (δHS-SPME). SPME analyses were conducted using a commercially available polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber having a film thickness of 65 μm (Supelco) as a capture medium. The experimentally optimized headspace sampling conditions were arranged (15 min. at 50^˚C) before a 30 min. sampling period.     

Deriving ozone dose-response of photosynthesis in adult forest trees from branch-level cuvette gas exchange assessment

Branch-level gas exchange provided the basis for assessing ozone flux in order to derive the dose-response relationship between cumulative O3 uptake (COU) and carbon gain in the upper sun crown of adult Fagus sylvatica. Fluxes of ozone, CO2 and water vapour were monitored simultaneously by climatized branch cuvettes. The cuvettes allowed branch exposure to an ambient or twice-ambient O3 regime, while tree crowns were exposed to the same O3 regimes (twice-ambient generated by a free-air canopy O3 exposure system). COU levels higher than 20mmolm(-2) led to a pronounced decline in carbon gain under elevated O3. The limiting COU range is consistent with findings on neighbouring branches exposed to twice-ambient O3 through free-air fumigation. The cuvette approach allows to estimate O3 flux at peripheral crown positions, where boundary layers are low, yielding a meso-scale within-crown resolution of photosynthetic foliage sensitivity under whole-tree free-air O3 fumigation.     

Atmospheric chemistry of HFE-7000 (CF(3)CF (2)CF (2)OCH (3)) and 2,2,3,3,4,4,4-heptafluoro-1-butanol (CF (3)CF (2)CF (2)CH (2)OH): kinetic rate coefficients and temperature dependence of reactions with chlorine atoms

Background, aim, and scope  The adverse environmental impacts of chlorinated hydrocarbons on the Earth’s ozone layer have focused attention on the effort to replace these compounds by nonchlorinated substitutes with environmental acceptability. Hydrofluoroethers (HFEs) and fluorinated alcohols are currently being introduced in many applications for this purpose. Nevertheless, the presence of a great number of C–F bonds drives to atmospheric long-lived compounds with infrared absorption features. Thus, it is necessary to improve our knowledge about lifetimes and global warming potentials (GWP) for these compounds in order to get a complete evaluation of their environmental impact. Tropospheric degradation is expected to be initiated mainly by OH reactions in the gas phase. Nevertheless, Cl atoms reaction may also be important since rate constants are generally larger than those of OH. In the present work, we report the results obtained in the study of the reactions of Cl radicals with HFE-7000 (CF₃CF₂CF₂OCH₃) (1) and its isomer CF₃CF₂CF₂CH₂OH (2). Materials and methods  Kinetic rate coefficients with Cl atoms have been measured using the discharge flow tube–mass spectrometric technique at 1 Torr of total pressure. The reactions of these chlorofluorocarbons (CFCs) substitutes have been studied under pseudo-first-order kinetic conditions in excess of the fluorinated compounds over Cl atoms. The temperature ranges were 266–333 and 298–353 K for reactions of HFE-7000 and CF₃CF₂CF₂CH₂OH, respectively. Results  The measured room temperature rate constants were k(Cl+CF₃CF₂CF₂OCH₃) = (1.24 ± 0.28) × 10⁻¹³ cm³ molecule⁻¹ s⁻¹and k(Cl+CF₃CF₂CF₂CH₂OH) = (8.35 ± 1.63) × 10⁻¹³ cm³ molecule⁻¹ s⁻¹ (errors are 2σ + 10% to cover systematic errors). The Arrhenius expression for reaction 1 was k ₁(266–333 K) = (6.1 ± 3.8) × 10⁻¹³exp[−(445 ± 186)/T] cm³ molecule⁻¹ s⁻¹ and k ₂(298–353 K) = (1.9 ± 0.7) × 10⁻¹²exp[−(244 ± 125)/T] cm³ molecule⁻¹ s⁻¹ (errors are 2σ). The reactions are reported to proceed through the abstraction of an H atom to form HCl and the corresponding halo-alkyl radical. At 298 K and 1 Torr, yields on HCl of 0.95 ± 0.38 and 0.97 ± 0.16 (errors are 2σ) were obtained for CF₃CF₂CF₂OCH₃ and CF₃CF₂CF₂CH₂OH, respectively. Discussion  The obtained kinetic rate constants are related to the previous data in the literature, showing a good agreement taking into account the error limits. Comparing the obtained results at room temperature, k ₁ and k ₂, HFE-7000 is significantly less reactive than its isomer C₃F₇CH₂OH. A similar behavior has been reported for the reactions of other fluorinated alcohols and their isomeric fluorinated ethers with Cl atoms. Literature data, together with the results reported in this work, show that, for both fluorinated ethers and alcohols, the kinetic rate constant may be considered as not dependent on the number of –CF₂– in the perfluorinated chain. This result may be useful since it is possible to obtain the required physicochemical properties for a given application by changing the number of –CF₂– without changes in the atmospheric reactivity. Furthermore, lifetimes estimations for these CFCs substitutes are calculated and discussed. The average estimated Cl lifetimes are 256 and 38 years for HFE-7000 and C₃H₇CH₂OH, respectively. Conclusions  The studied CFCs’ substitutes are relatively short-lived and OH reaction constitutes their main reactive sink. The average contribution of Cl reactions to global lifetime is about 2% in both cases. Nevertheless, under local conditions as in the marine boundary layer, τ _Cl values as low as 2.5 and 0.4 years for HFE-7000 and C₃H₇CH₂OH, respectively, are expected, showing that the contribution of Cl to the atmospheric degradation of these CFCs substitutes under such conditions may constitute a relevant sink. In the case of CF₃CF₂CF₂OCH₃, significant activation energy has been measured, thus the use of kinetic rate coefficient only at room temperature would result in underestimations of lifetimes and GWPs. Recommendations and perspectives  The results obtained in this work may be helpful within the database used in the modeling studies of coastal areas. The knowledge of the atmospheric behavior and the structure–reactivity relationship discussed in this work may also contribute to the development of new environmentally acceptable chemicals. New volatile materials susceptible of emission to the troposphere should be subject to the study of their reactions with OH and Cl in the range of temperature of the troposphere. The knowledge of the temperature dependence of the kinetic rate constants, as it is now reported for the case of reactions 1 and 2, will allow more accurate lifetimes and related magnitudes like GWPs. Nevertheless, a better knowledge of the vertical Cl tropospheric distribution is still required.     

Self-ignition and explosion during discharge of high-pressure hydrogen

The phenomenon of self-ignition and explosion during discharge of high-pressure hydrogen was investigated. To clarify the ignition conditions of high-pressure hydrogen jets, rapid discharge of the high-pressure hydrogen was examined experimentally. A diaphragm was used to allow rapid discharge of the high-pressure hydrogen. The burst pressure was varied from 4 to 30 MPa. The downstream geometry of the diaphragm was a flange and extension pipes, with the pipe length varying from 3 to 300 mm. The diameter of the nozzle was 5 or 10 mm. When short pipes were used, the hydrogen jet did not ignite. However, the hydrogen jet showed an increasing tendency to ignite in the pipe as the length of the pipe became longer. At higher burst pressures, a diffusion jet flame was formed from the pipe. The blast wave from the fireball formed on self-ignition of the hydrogen jet resulted in an extremely rapid pressure rise.     

天然气处理厂放空火炬影响分析与模拟计算

根据天然气处理厂的地理和气象条件,提出需要进行危险性评估的4种工况;采用喷射扩散模式计算喷射火焰的热辐射,模拟不同工况下,风速不同时的热辐射强度曲线;采用高斯三维模型计算气体扩散浓度,得出不同工况下,风速不同时气体扩散长度和高度,并对放空火炬紧急工况时不同风速下的气体扩散进行模拟。通过影响分析和模拟,得出该放空火炬在不同风速下,不使人员产生热辐射影响的最小安全距离。