Suitability of ignition source “exploding wire” for determination of dust explosion characteristics in the 20-L-sphere

Several safety characteristics of dusts are determined in the 20-L-sphere (also known as SIWEK Chamber) according to international standards. Dust cloud ignition is carried out using pyrotechnical igniters. Due to various disadvantages of such igniters the need for alternative ignition sources arises again and again. An alternative could be an ignition source which is known as “exploding wire” or “fuse wire”. The paper presents test results of a comparative study between both ignition sources for the determination of the safety characteristics “Maximum Explosion Pressure” and “Maximum Rate of Explosion Pressure Rise” of five selected dusts in the 20-L-sphere. In addition to that the ignition mechanisms of both ignition sources were analyzed by high speed camera recordings and the ignition energy was determined with electric and calorimetric recordings. The paper shows results of measurements of the ignition energy of both ignition sources as well as sequences of the flame propagation.     

Validation of geometry modelling approaches for offshore gas dispersion simulations

Computational Fluid Dynamics (CFD) codes are widely used for gas dispersion studies on offshore installations. The majority of these codes use single-block Cartesian grids with the porosity/distributed-resistance (PDR) approach to model small geometric details. Computational cost of this approach is low since small-scale obstacles are not resolved on the computational mesh. However, there are some uncertainties regarding this approach, especially in terms of grid dependency and turbulence generated from complex objects. An alternative approach, which can be implemented in general-purpose CFD codes, is to use body-fitted grids for medium to large-scale objects whilst combining multiple small-scale obstacles in close proximity and using porous media models to represent blockage effects. This approach is validated in this study, by comparing numerical predictions with large-scale gas dispersion experiments carried out in DNV GL's Spadeadam test site. Gas concentrations and gas cloud volumes obtained from simulations are compared with measurements. These simulations are performed using the commercially available ANSYS CFX, which is a general-purpose CFD code. For comparison, further simulations are performed using CFX where small-scale objects are explicitly resolved. The aim of this work is to evaluate the accuracy and efficiency of these different geometry modelling approaches.     

Influence of active mitigation barriers on LNG dispersion

In recent years, particular interest has been direct to the issues of risk associated with the storage, transport and use of Liquefied Natural Gas (LNG) due to the increasing consideration that it is receiving for energy applications. Consequently, a series of experimental and modeling studies to analyze the behavior of LNG have been carried out to collect an archive of evaporation, dispersion and combustion information, and several mathematical models have been developed to represent LNG dispersion in realistic environments and to design mitigation barriers.This work uses Computational Fluid Dynamics codes to model the dispersion of a dense gas in the atmosphere after accidental release. In particular, it will study the dispersion of LNG due to accidental breakages of a pipeline and it will analyze how it is possible to mitigate the dispersing cloud through walls and curtains of water vapor and air, also providing a criterion for the design of such curtains.     

An evaluation of risk assessment framework for industrial accidents in India

Due to rapid industrialization, with high population density and constraints of land, it is expected that level of risks arising from the hazardous industries will increase in India in the coming decades. However, 30 years after the Bhopal accident (1984), except a few discrete regulations, there is as yet no integrated system for assessing and managing risks arising out of these hazardous industries in India. The gravity of aspects related to the management of industrial risk still remains crucially important. In particular, there is no standard guideline on risk analysis methodology, acceptability or tolerability criteria, nor is there an accident database or a risk reduction strategy for the areas where risk levels are already high. On top of this, there are technical and legislative gaps in the institutional framework to implement any of the above mentioned issues. With the backdrop of the Bhopal gas tragedy, the objective of this paper is therefore to evaluate the effectiveness of a comprehensive risk assessment framework for the emerging economy of India, in order to control and/or to reduce the risk level that exists. In this context, regulations and policies pertaining to industrial risk assessment were reviewed.     

Application and effect of negative pressure chambers on pipeline explosion venting

Explosion venting is a frequently-used way to lower explosion pressure and accident loss. Recently, studies of vessel explosion venting have received much attention, while little attention has been paid to pipe explosion venting. This study researched the characteristics of explosion venting for Coal Bed Methane (CBM) transfer pipe, and proposed the way of explosion venting to chamber in order to avoid the influence of explosion venting on external environment, and investigated the effects of explosion venting to atmosphere and chamber. When explosion venting to atmosphere, the average explosion impulse 4.89 kPa s; when explosion venting to 0 MPa (atmospheric pressure) chamber, average explosion impulse is 7.52 kPa s; when explosion venting to −0.01 MPa chamber, explosion flame and pressure obviously drop, and average explosion impulse decreases to 4.08 kPa s; when explosion venting to −0.09 MPa chamber, explosion flame goes out and average explosion impulse is 1.45 kPa s. Thus, the effect of explosion venting to negative chamber is far better than that to atmospheric chamber. Negative chamber can absorb more explosion gas and energy, increase stretch of explosion flame, and eliminate free radical of gas explosion. All these can promote the effect of explosion venting to negative chamber.     

A CFD-based approach for gas detectors allocation

Accidental gas releases are detected by allocating sensors in optimal places to prevent escalation of the incident. Gas release effects are typically assessed based on calculating the dispersion from releasing points. In this work, a CFD-based approach is proposed to estimate gas dispersion and then to obtain optimal gas sensors allocation. The Ansys-Fluent commercial package is used to estimate concentrations in the open air by solving the governing equations of continuity, momentum, energy and species convection-diffusion combined with the realizable κ-ε model for turbulence viscosity effects. CFD dynamic simulations are carried out for potential gas leaks, assuming worst-case scenarios with F-stability and 2 m/s wind speed during a 4 min releasing period and considering 8 wind directions. The result is a scenario-based methodology to allocate gas sensors supported on fluid dynamics models. The three x–y–z geographical coordinates for the sensor allocation are included in this analysis. To highlight the methodology, a case study considers releases from a large container surrounded by different types of geometric units including sections with high obstacles, low obstacles, and no obstacles. A non-redundant set of perfect sensors are firstly allocated to cover completely the detection for all simulations releases. The benefits of redundant detection via a MooN voting arranging scheme is also discussed. Numerical results demonstrate the capabilities of CFD simulations for this application and highlight the dispersion effects through obstacles with different sizes.     

Effect of bifurcation on premixed methane-air explosion overpressure in pipes

It is well known that bifurcation structures have a significant influence on gas explosions in pipelines or roadways. In this work, three different types of bifurcation, namely, bifurcation with two right angles (BTRAs), bifurcation with two obtuse angles (BTOAs), and bifurcation with an obtuse angle and an acute angle (BOAA), were used to study the effect of bifurcation on premixed methane–air explosion overpressure in pipes. The effect of the position of bifurcation on gas explosions was also discussed. Our results suggest that the peak overpressure evolution in pipes exhibits a downtrend before the bifurcation, a sharp increase after the bifurcation until reaching the maximum, and a downward trend when propagating into the pipe end. It was also found that gas-explosion propagation was affected by the joint action of turbulence induced by obstacles and the abrupt increase of the cross-sectional area. In addition, the bifurcation’s position had only a small effect on the maximum peak overpressure in pipes.     

Enhancement of ultrasonic disintegration of sewage sludge by aeration

Sonication is an effective way for sludge disintegration,which can significantly improve the efficiency of anaerobic digestion to reduce and recycle use of sludge.But high energy consumption limits the wide application of sonication.In order to improve ultrasonic sludge disintegration efficiency and reduce energy consumption,aeration was introduced.Results showed that sludge disintegration efficiency was improved significantly by combining aeration with ultrasound.The aeration flow rate,gas bubble size,ultrasonic density and aeration timing had impacts on sludge disintegration efficiency.Aeration that used in later stage of ultrasonic irradiation with low aeration flow rate,small gas bubbles significantly improved ultrasonic disintegration sludge efficiency.At the optimal conditions of 0.4 W/m L ultrasonic irradiation density,30 m L/min of aeration flow rate,5 min of aeration in later stage and small gas bubbles,ultrasonic sludge disintegration efficiency was increased by 45% and one third of ultrasonic energy was saved.This approach will greatly benefit the application of ultrasonic sludge disintegration and strongly promote the treatment and recycle of wastewater sludge.     

ICP-OES法测定大气和废气颗粒物中的金属元素

将微波消解法与电感耦合等离子体发射光谱法(ICP-OES)相结合,对大气和废气颗粒物中金属元素的微波消解条件及ICP-OES测定条件进行了优化研究,建立了大气和废气颗粒物中铝(Al)、钡(Ba)、镉(Cd)、铬(Cr)、铜(Cu)、锰(Mn)、钼(Mo)、镍(Ni)、铅(Pb)、锡(Sn)、锶(Sr)及锌(Zn)等金属元素的测定方法。对方法的检出限进行了测定,各元素的检出限均低于0.04 mg/L;对方法的精密度进行了测定,各元素的相对标准偏差在2.59%～7.14%之间;对方法的准确度进行了测定,质控滤膜中各元素的回收率在89.6%~119%之间,颗粒物参考物质中各元素的回收率在85.1%～107%之间,并将该方法成功应用到 TSP、污染源废气实际样品中金属元素的测定。     

热脱附法在测定空气中苯系物上的应用

对热脱附-气相色谱测定苯系物方法中的几种常用吸附剂进行了选择比较。结果表明,在测定苯、甲苯、乙苯、二甲苯以及苯乙烯时,TenaxTA/Carbograph1TD复合型吸附剂的综合吸附效率最好。TenaxTA/Carbograph1TD复合型吸附剂的检出限、精密度、准确度和保存期都得到了良好的结果,能够满足监测分析的要求。