Mycological assessment of sediments in Ligurian beaches in the Northwestern Mediterranean: pathogens and opportunistic pathogens

Sediments of five Ligurian beaches in compliance with European Union bathing water regulations were studied based on the characteristics of the fungal assemblage during the tourism season. Among the 179 taxa of filamentous fungi isolated, 120 were opportunistic pathogens, such as Acremonium sp., and the genus Penicillium was also present as the pathogenic species P. citrinum. Furthermore, 5% of the total filamentous fungi belonged to the dermatophyte genus Microsporum, whose species can cause mycoses. Beach sediments showed elevated densities of opportunistic pathogens, of pathogenic filamentous fungi, and of yeasts during the tourism season. Although monitoring of beach sediments for microbiological contamination is not mandatory, and disease transmission from sediments has not yet been demonstrated, our study suggests that beach sediments may act as a reservoir of potential pathogens, including fungi. In addition, the mycoflora displayed high sensitivity to critical environmental situations in the beaches studied. Therefore, the fungal community can be a useful tool for assessing the quality of sandy beaches in terms of sanitary and environmental quality.     

血压监护系统的电路分析和印刷电路板设计

本文介绍了血压监护系统的电路设计,其中前端电路的设计采用差分多级放大电路,达到放大的效果。应用PSpice软件对滤波电路进行了仿真,得到了带通滤波器的通带频率,验证了滤波器设计的可行性。同时本文对血压监护系统印刷电路板中电磁兼容问题进行了研究,对血压监护系统电路板的布局布线规则进行了规划和设计。     

电子信息行业的水环境压力分析

电子信息行业长期以来都被定义为一个“高产值、低能耗”的清洁产业,其水环境压力经常被低估.以长三角电子信息产业集群的核心地区太湖流域为例,对电子信息行业的水资源消耗、废水和主要污染物排放以及危险废弃物的处置等方面进行了评估,发现高度集聚的巨大产能与特定区域水环境容量的矛盾、污染的产业链转移以及处于“微笑”曲线底部引致的环境投入压力是我国电子信息行业水环境压力的主要表现.     

植被混凝土在官地水电站的试验分析

本文主要对官地水电站高陡边坡植被混凝土前期绿化试验成果进行分析,以寻求在干湿季节明显、雨量集中、干旱季节漫长、温度高、蒸发量大等干热河谷气候特征条件下的最佳生境构筑方法,为官地水电站乃至雅砻江流域水电工程高陡边坡生态恢复提供技术依据。     

Sewage sludge disintegration by high-pressure homogenization: A sludge disintegration model

High-pressure homogenization (HPH) technology was applied as a pretreatment to disintegrate sewage sludge. The effects of homogenization pressure, homogenization cycle number, and total solid content on sludge disintegration were investigated. The sludge disintegration degree (DDCOD), protein concentration, and polysaccharide concentration increased with the increase of homogenization pressure and homogenization cycle number, and decreased with the increase of sludge total solid (TS) content. The maximum DDCOD of 43.94% was achieved at 80 MPa with four homogenization cycles for a 9.58 g/L TS sludge sample. A HPH sludge disintegration model of DD_COD= kN^aP^b was established by multivariable linear regression to quantify the effects of homogenization parameters. The homogenization cycle exponent a and homogenization pressure exponent b were 0.4763 and 0.7324 respectively, showing that the effect of homogenization pressure (P) was more significant than that of homogenization cycle number (N). The value of the rate constant k decreased with the increase of sludge total solid content. The specific energy consumption increased with the increment of sludge disintegration efficiency. Lower specific energy consumption was required for higher total solid content sludge.     

一种适用于深水压试验的传压隔热装置设计

目的真实高效地进行深水压环境的温度模拟。方法提出一种深水压试验压力加载过程中的恒温实现方法,通过开展基于皮囊的结构设计、密封性设计、导热性研究等工作,设计一种适用于深水压试验的传压隔热装置,对其进行理论分析和仿真计算。结果该装置可以实现液体温度在较长时间内基本恒定,具有良好的传压隔热性能。结论在建立的实验系统上进行了试验研究,实现了深水压环境模拟试验中压力载荷同步条件下液体温度小范围恒定功能,该技术为深水压环境试验的相关技术研究提供了技术储备。     

油田用钨合金镀层腐蚀性能评价研究

目的评价钨合金镀层油管的腐蚀性能。方法利用高压釜模拟高压气井和高含硫气井的腐蚀环境,进行高压高温腐蚀试验,以及标准的氢致开裂(HIC)和硫化氢应力腐蚀试验。采用电子扫描显微镜(SEM)及其能谱仪(EDS)和X射线衍射分析仪(XRD),分析或检测钨合金镀层和基管的腐蚀形貌、腐蚀产物的组成。结果油管表面的钨合金镀层平整而致密,其主要组成元素为W和Ni。高温高压腐蚀试验后,镀层仍然致密平整,腐蚀程度轻微。在60、90、120、140℃试验7天时,镀层和基材的H_2S/CO_2腐蚀速率分别为0.0179、0.0093、0.0102、0.0369 mm/a和1.030、1.272、1.183、0.991 mm/a。试验30天,在120℃时,其H_2S/CO_2腐蚀速率分别为-0.0085、0.1789 mm/a;在160℃时,其CO_2腐蚀速率分别为0.0091、0.8976 mm/a。该钨合金镀层均通过了标准的氢致开裂和硫化氢应力腐蚀试验。结论该钨合金镀层具有很好的耐腐蚀性能。     

动态膜压法测定江、污混合水体中有机物含量的探讨

用双驱动动态膜压仪测定江、污混合水中有机物含量。通过测定白龙港污水和长江水混合后的膜压和滞回环面积，用它们与相应的经典法CODCr作图，获得了滞回环面积和CODCr之间良好地线性关系，表明用动态膜压法可快速测定混合水中的有机物含量，不须加任何试剂，不会产生二次污染。同时，对实验结果进行了初步的机理探讨。     

Optimization of the high-pressure, near-critical liquid-based microsortation of recyclable post-consumer plastics

High-pressure, near-critical liquids were used as float-sink separation media for the microsortation of polyolefin mixtures and PET/PVC mixtures. Near-critical carbon dioxide was used for the refinement of the polyolefins, and sulfur hexafluoride was used to separate post-consumer PVC from PET. Preliminary experiments indicated that there was no overlap in the density ranges of post-consumer HDPE, LDPE and PP containers. There was no overlap in the PET and PVC densities, with the exception of a single PVC packaging material with a density in the PET range. These initial results indicated that a float-sink separation was a viable means of microsortation. Separations of 91% LDPE (1/8′ beads)/9% PP (1/8′ chopped strands) resin mixtures and mixed post-consumer polyolefin flakes were then conducted in a laboratory-scale, 1-I batch apparatus. This apparatus not only permitted the observation of the separation, but also enabled the separated fractions to be removed from the high-pressure environment. The results indicated that LDPE purity of greater than 98.9% was obtained in 3 min or less if (a) the fluid density was 0.018 g/cm³ greater than the PP density and only 0.002 g/cm³ less than the LDPE density, thereby providing the greatest buoyancy force for the removal of the PP, (b) the fluid was recirculated upward through the bed of mixed plastics, facilitating the upward movement of the PP, and (c) the loading was kept at levels below 40% by volume. HDPE purity of 99% was also attained with clean, dry, post-consumer mixed plastic flakes. The loadings for these separations were very low, however, due to the difficulty in agitating the mixed bed of plastics using fluid recirculation. An economic analysis of these microsortation processes indicated that the value of the sorted plastics relative to the mixed feed must increase by approx. $0.08/lb for the CO₂-based separation and approx. $0.27/lb for the SF₆-based separation to justify the implementation of these high-pressure processes.     

循环热处理对高速钢超塑性的影响

此文研究了循环热处理工艺对W6Mo5Cr4V2钢超塑性的影响.结果表明:该钢在1040℃两次循环淬火是实现其超塑性的最佳热处理工艺;按此工艺进行预处理后,在810℃、初始应变速率为5.56×10~(-1)s~(-1)的条件下,该钢的超塑延伸率可达187%.