Sewage sludge disintegration by high-pressure homogenization: A sludge disintegration model

High-pressure homogenization (HPH) technology was applied as a pretreatment to disintegrate sewage sludge. The effects of homogenization pressure, homogenization cycle number, and total solid content on sludge disintegration were investigated. The sludge disintegration degree (DDCOD), protein concentration, and polysaccharide concentration increased with the increase of homogenization pressure and homogenization cycle number, and decreased with the increase of sludge total solid (TS) content. The maximum DDCOD of 43.94% was achieved at 80 MPa with four homogenization cycles for a 9.58 g/L TS sludge sample. A HPH sludge disintegration model of DD_COD= kN^aP^b was established by multivariable linear regression to quantify the effects of homogenization parameters. The homogenization cycle exponent a and homogenization pressure exponent b were 0.4763 and 0.7324 respectively, showing that the effect of homogenization pressure (P) was more significant than that of homogenization cycle number (N). The value of the rate constant k decreased with the increase of sludge total solid content. The specific energy consumption increased with the increment of sludge disintegration efficiency. Lower specific energy consumption was required for higher total solid content sludge.     

一种适用于深水压试验的传压隔热装置设计

目的真实高效地进行深水压环境的温度模拟。方法提出一种深水压试验压力加载过程中的恒温实现方法,通过开展基于皮囊的结构设计、密封性设计、导热性研究等工作,设计一种适用于深水压试验的传压隔热装置,对其进行理论分析和仿真计算。结果该装置可以实现液体温度在较长时间内基本恒定,具有良好的传压隔热性能。结论在建立的实验系统上进行了试验研究,实现了深水压环境模拟试验中压力载荷同步条件下液体温度小范围恒定功能,该技术为深水压环境试验的相关技术研究提供了技术储备。     

油田用钨合金镀层腐蚀性能评价研究

目的评价钨合金镀层油管的腐蚀性能。方法利用高压釜模拟高压气井和高含硫气井的腐蚀环境,进行高压高温腐蚀试验,以及标准的氢致开裂(HIC)和硫化氢应力腐蚀试验。采用电子扫描显微镜(SEM)及其能谱仪(EDS)和X射线衍射分析仪(XRD),分析或检测钨合金镀层和基管的腐蚀形貌、腐蚀产物的组成。结果油管表面的钨合金镀层平整而致密,其主要组成元素为W和Ni。高温高压腐蚀试验后,镀层仍然致密平整,腐蚀程度轻微。在60、90、120、140℃试验7天时,镀层和基材的H_2S/CO_2腐蚀速率分别为0.0179、0.0093、0.0102、0.0369 mm/a和1.030、1.272、1.183、0.991 mm/a。试验30天,在120℃时,其H_2S/CO_2腐蚀速率分别为-0.0085、0.1789 mm/a;在160℃时,其CO_2腐蚀速率分别为0.0091、0.8976 mm/a。该钨合金镀层均通过了标准的氢致开裂和硫化氢应力腐蚀试验。结论该钨合金镀层具有很好的耐腐蚀性能。     

动态膜压法测定江、污混合水体中有机物含量的探讨

用双驱动动态膜压仪测定江、污混合水中有机物含量。通过测定白龙港污水和长江水混合后的膜压和滞回环面积，用它们与相应的经典法CODCr作图，获得了滞回环面积和CODCr之间良好地线性关系，表明用动态膜压法可快速测定混合水中的有机物含量，不须加任何试剂，不会产生二次污染。同时，对实验结果进行了初步的机理探讨。     

Optimization of the high-pressure, near-critical liquid-based microsortation of recyclable post-consumer plastics

High-pressure, near-critical liquids were used as float-sink separation media for the microsortation of polyolefin mixtures and PET/PVC mixtures. Near-critical carbon dioxide was used for the refinement of the polyolefins, and sulfur hexafluoride was used to separate post-consumer PVC from PET. Preliminary experiments indicated that there was no overlap in the density ranges of post-consumer HDPE, LDPE and PP containers. There was no overlap in the PET and PVC densities, with the exception of a single PVC packaging material with a density in the PET range. These initial results indicated that a float-sink separation was a viable means of microsortation. Separations of 91% LDPE (1/8′ beads)/9% PP (1/8′ chopped strands) resin mixtures and mixed post-consumer polyolefin flakes were then conducted in a laboratory-scale, 1-I batch apparatus. This apparatus not only permitted the observation of the separation, but also enabled the separated fractions to be removed from the high-pressure environment. The results indicated that LDPE purity of greater than 98.9% was obtained in 3 min or less if (a) the fluid density was 0.018 g/cm³ greater than the PP density and only 0.002 g/cm³ less than the LDPE density, thereby providing the greatest buoyancy force for the removal of the PP, (b) the fluid was recirculated upward through the bed of mixed plastics, facilitating the upward movement of the PP, and (c) the loading was kept at levels below 40% by volume. HDPE purity of 99% was also attained with clean, dry, post-consumer mixed plastic flakes. The loadings for these separations were very low, however, due to the difficulty in agitating the mixed bed of plastics using fluid recirculation. An economic analysis of these microsortation processes indicated that the value of the sorted plastics relative to the mixed feed must increase by approx. $0.08/lb for the CO₂-based separation and approx. $0.27/lb for the SF₆-based separation to justify the implementation of these high-pressure processes.     

Vapour pressures, aqueous solubility, Henry's law constants and air/water partition coefficients of 1,8-dichlorooctane and 1,8-dibromooctane

New data on the vapour pressures and aqueous solubility of 1,8-dichlorooctane and 1,8-dibromooctane are reported as a function of temperature between 20 °C and 80 °C and 1 °C and 40 °C, respectively. For the vapour pressures, a static method was used during the measurements which have an estimated uncertainty between 3% and 5%. The aqueous solubilities were determined using a dynamic saturation column method and the values are accurate to within ±10%. 1,8-Dichlorooctane is more volatile than 1,8-dibromooctane in the temperature range covered (p_sat varies from 3 to 250 Pa and from 0.53 to 62 Pa, respectively) and is also approximately three times more soluble in water (mole fraction solubilities at 25 °C of 5.95 × 10⁻⁷ and 1.92 × 10⁻⁷, respectively). A combination of the two sets of data allowed the calculation of the Henry’s law constants and the air water partition coefficients. A simple group contribution concept was used to rationalize the data obtained.     

低压下聚乙烯绝缘层导线火蔓延熔融滴落实验分析

低压导线火蔓延的研究对于飞机和航天器的防火安全具有重要意义。针对镍铬合金线芯、聚乙烯(PE)绝缘层导线火蔓延过程中的熔融滴落现象,在低压舱内开展了不同气压、不同氧气浓度的大量实验研究,获得了导线熔融滴落频率、质量和火蔓延速度,以及不同氧浓度熔融滴落的上下限。结果表明:(1)在熔融滴落过程中,由于滴落会产生向上的动量,从而使火焰在滴落后发生突然的"跳动"现象,火焰高度先增加后降低;(2)滴落上限和滴落下限随着氧浓度的增加而降低,并且可以划分为3个不同的区域:火蔓延仅存区;滴落和火蔓延共存区;无滴落无火蔓延区。滴落上限和滴落下限下降曲线在50%氧浓度、5kPa压力发生会合,此后只有火蔓延而不存在滴落现象。(3)当压力降低时,由于线芯温度增加,线芯传导热量增加,导致绝缘层熔融速率加快,从而使得滴落频率增加,同时液滴的表面张力随着压力的降低而增加,使得低压下液滴的质量变大。     

Pipeline leakage detection and isolation: An integrated approach of statistical and wavelet feature extraction with multi-layer perceptron neural network (MLPNN)

Leakage diagnosis of hydrocarbon pipelines can prevent environmental and financial losses. This work proposes a novel method that not only detects the occurrence of a leakage fault, but also suggests its location and severity. The OLGA software is employed to provide the pipeline inlet pressure and outlet flow rates as the training data for the Fault Detection and Isolation (FDI) system. The FDI system is comprised of a Multi-Layer Perceptron Neural Network (MLPNN) classifier with various feature extraction methods including the statistical techniques, wavelet transform, and a fusion of both methods. Once different leakage scenarios are considered and the preprocessing methods are done, the proposed FDI system is applied to a 20-km pipeline in southern Iran (Goldkari-Binak pipeline) and a promising severity and location detectability (a correct classification rate of 92%) and a low False Alarm Rate (FAR) were achieved.     

爆炸波在饱和土介质中传播时压力变化规律的试验研究

介绍了在Φ900平面波加载器中进行的饱和土爆炸波传播试验,通过试验比较系统地研究了爆炸波在饱和土自由场中的传播规律及其在刚性边界上的反射问题。试验表明饱和土中的气体含量是控制波传播规律的主要因素,在深度方向上自由场应力峰值可能随深度增加,而在刚性边界上荷载反射系数可能>2。对饱和土与非饱和土中波传播规律的区别,在确定饱和土中结构的设计荷载时必须给予极大的关注。     

Theoretical equation of gas desorption of particle coal under the non-uniform pressure condition and its analytical solution

Based on the second Fick’s law, the theoretical equation of gas desorption of particle coal under the non-uniform pressure condition was developed in this paper. The analytical solution of the theoretical equation and the method of gas desorption quantity of particle coal under non-uniform pressure condition were obtained.