成炭型有机大分子/层状无机物复合成炭剂的制备及应用研究

层状无机物在聚合物基体中易团聚,限制了其在聚合物材料中的规模化应用。本工作通过将有机改性蒙脱土(OMMT)与一种具有超支化结构的磷氮大分子化合物HTPPP(以三嗪结构为基础,通过焦磷酸结构连接)在醇水体系中混合溶胀,再经过高温脱水,制备成HTPPP插层、剥离的OMMT成炭型有机大分子/层状无机物复合成炭剂(HTPPP-OMMT)。XRD测试表明层状结构的OMMT能够在HTPPP中被完全剥离。OMMT的复合降低了HTPPP的水溶性,并提高了其热稳定性。将有机/无机复合成炭剂HTPPP-OMMT作为单组分无卤膨胀阻燃剂应用于聚丙烯(PP),阻燃测试表明HTPPP-OMMT复合成炭剂的阻燃效率高于HTPPP。这是由于其在材料燃烧过程中能够催化形成更加致密的膨胀多孔炭层,而炭层在高温下的热氧稳定性更好。此外,有机/无机复合改善了HTPPP-OMMT在PP的相容性,能提高材料的力学和耐析出性能。     

Assessment of frequent cutting as a plant-community management technique in power-line corridors

Repeated cutting of vegetation at or near ground level in power-line corridors is a common practice for inhibiting tree growth and regeneration. However, few data exist on long-term community responses. In this study, we sampled 20 northern Kentucky power-line corridors and compared their seedling and sapling communities to the edges and interiors of adjacent undisturbed forests. Mean seedling and sapling density in corridors was roughly twice that of adjacent undisturbed forest interiors, suggesting that repeated cutting is not a viable method of inhibiting tree regeneration. Corridor communities were dominated byRobinia pseudoacacia (black locust) andFraxinus americana (white ash), but ordinations indicated strong similaritties among communities in corridors and adjacent forests. Many of the tree species found in adjacent forests, with the exception of a few shade-tolerant species, had highest seedling and sapling densities in corridors. Stump or root sprouting by many species appears to regenerate forests quickly after cutting. However, disturbed soil and detritus accumulations caused by management crews and their equipment may also create a large variety of microsites for seedling establishment. Because repeated cutting selects for dominance by species with highest sprout growth rates, it should not be used as the sole management technique. It may instead be used to alter the vigor, stature, and stored reserves of trees so that herbicides or other methods of tree control can be used more efficiently.     

合成洗涤剂生产废水处理技术研究

分别用混凝沉降，泡沫分离，活性炭吸附工艺进行了合成洗涤剂生产废水的处理试验。研究结果表明，混凝沉降、泡沫分离法的直链烷基苯磺酸钠去除率可以分别达到９０％、８０％以上，活性炭的ＬＡＳ吸附容量可达５９ｍｇ／ｇ以上，处理后废水的ＬＡＳ、ＣＯＤ浓度可达到国家排放标准。     

新型声屏障材料泡沫陶瓷

通过对泡沫陶瓷吸声特性的介绍 ,指出泡沫陶瓷具有良好的声学性能 ,力学性能 ,耐候性 ,防火性等特点 ,其材料制成的吸声元件 ,在中低频具有良好的吸声性能 ,适于在公路建造声屏障时使用     

废弃电子设备的资源化研究发展现状

分析了废弃电子设备的主要特点、资源化回收与利用的不同方法及其优缺点，并详细介绍了废弃电子设备机械处理的研究及工业应用现状。     

Octachlorinated dioxin in pulps and effluents: Where does it come from?

Studies on the formation/destruction of dioxins associated with the pulping of wood artificially impregnated with an industrial grade of pentachlorophenol lend support to an earlier observation that ambient dioxins deposition may not necessarily be a unique source of the higher chlorinated dioxins occasionally found in pulps and final effluent discharges. These dioxins, which seemingly occur in products from a wide range of pulping technologies including recycle operations, may also originate from pentachlorophenol-based fungicides.     

甘肃省土壤环境机械组成调查研究

通过对甘肃省土壤环境机械组成的调查研究，较全面、系统地获得了各种元素、土类以及各区域的土壤环境机械组成，找出了本省土壤环境机械组成特征及其分布规律。     

微米级空心玻璃微珠三相泡沫稳定性研究

基于水成膜泡沫灭火剂(AFFF),用微米级空心微珠颗粒作为泡沫稳定剂,制成三相泡沫,并研究了泡沫组成因素对发泡能力和泡沫稳定性的影响。采用控制变量法,研究了颗粒浓度、颗粒粒径、AFFF原液浓度对发泡倍数和析液时间的影响。颗粒加入对发泡能力有抑制作用;因为颗粒存在影响,三相泡沫的发泡能力随AFFF原液浓度增大而减小;40μm粒径颗粒的抑制作用相对20μm和60μm颗粒最小。颗粒浓度和AFFF原液浓度增加,能够提升三相泡沫稳定性,且泡沫析液时间随颗粒浓度增加呈指数规律变化。当AFFF原液浓度为3.0%、颗粒浓度为9%左右时,三相泡沫稳定时间约为两相泡沫的3倍,该配方三相泡沫有较好的稳定性。     

Physics of failure analysis of power section assembly for positive displacement motor

Power section assembly is the core part of positive displacement motor (PDM), and its mechanical behavior and service life determine the drilling efficiency and cycle. In this paper, fault tree of power section assembly was established, failure reasons were analyzed and improvement measures were put forward. Finite element models of conventional lining and uniform wall thickness lining of 5/6 PDM were established, and the mechanical behaviors were investigated. Working parameters such as drilling fluid pressure, rubber hardness, downhole temperature and pressure difference were discussed. The results show that wear and rust are the main failure modes of the rotor. Failure modes of rubber lining are wear, tear, rupture, peeling off, thermal failure and fatigue failure. Under the action of drilling fluid pressure, the maximum effective stress of rubber lining appears in the bottom of arc, and the minimum stress appears at the top of arc. But deformation distribution is opposite to the effective stress. Deformation of uniform wall thickness lining is more uniform. Effective stress of the lining increases with the increasing of drilling fluid pressure and rubber hardness, but it decreases with the downhole temperature increases. Deformation of the lining increases with the drilling fluid pressure increases, but it decreases with the increasing of rubber hardness and downhole temperature. Effective stress and deformation distribution of rubber lining are more uneven with the pressure difference increases. High stress area lies between the two smallest chambers.     

Utilization of limestone dust waste as filler in natural rubber

The possibility of using limestone dust waste (LDW) as a filler in natural rubber (NR) was investigated. First, the basic properties of LDW were characterized; LDW was then incorporated into NR and the compound properties were determined. Comparison of the reinforcing effect of LDW and other commercial fillers such as light-precipitated calcium carbonate (PCC) and nanoprecipitated calcium carbonate (NPCC) was made. The results revealed that even though the addition of LDW has little effect on compound processability, it has a negative effect on most mechanical properties, e.g., tensile strength, tear strength, and abrasion resistance, of the vulcanizate. Among the three fillers, the degree of reinforcement could be placed in the following order: NPCC > PCC > LDW. Due to their relatively low specific surface area and thus low reinforcement ability, both LDW and PCC can be grouped as nonreinforcing fillers, whereas NPCC, the specific surface area of which is relatively high, could be grouped as a semi-reinforcing filler for rubber.