以亲水化改性聚氨酯为多孔载体的生物膜移动床反应器处理污水中试研究

载体是生物膜移动术反应器(MBBR)工艺的关键影响因素,利用亲水化改性聚氨酯载体构建MBBR,用于城市污水的中试研究.反应器日处理能力为3～3.5 t.d-1,水力停留时间为7～8 h,在连续进水(进水COD 140～280 mg.L-1,NH4+-N 30～50 mg.L-1,总氮45～65 mg.L-1,总磷2.5～4.0 mg.L-1)条件下对改性载体的挂膜速度、有机物和氮的去除效果及不同温度下的污水处理特性进行了研究.140 d的试验结果表明在24～28℃时,载体上生物膜在6 d左右即可完成挂膜,并达到稳定的处理效果.COD、NH4+-N、TN和TP的平均去除率分别为70%、97%、70%和39%.随着水温逐渐降低到12℃左右,NH4+-N的去除率依然能达到97%,表明通过添加改性载体可以提高反应器低温条件下的硝化能力.     

高温气冷堆陶瓷堆内构件热老化试验平台开发

目的 开发一种试验平台模拟高温气冷堆正常工况、氧化腐蚀工况和事故工况试验条件,研究陶瓷堆内构件的氧化腐蚀行为和长期服役热老化规律。方法 通过分析高温气冷堆陶瓷堆内构件服役环境特征,确定试验平台开发技术要求,其主要部件包括氧气流量控制器、氦气流量控制器、储气罐、反应气流量控制器、气体预热器、高温反应炉、气体循环泵、氦气纯化器、纯水罐、蠕动泵、真空泵、排气冷肼、在线气相色谱仪、在线露点仪等。结果 该试验平台可精确控制在冷却剂氦气中混入微量的O2、H2O杂质,研究反应时间、温度等因素的影响,还可模拟高温堆正常工况和蒸汽发生器传热管破裂进水事故工况条件,开展长达3 000 h以上的连续热老化试验。结论 该试验平台具有高精度、大尺寸、耐高温、耐长周期试验等优异特性,可模拟复杂多样的工况条件,开展热老化试验研究。     

基于响应面法SCR脱硝反应器喷氨格栅的优化研究

利用计算流体动力学（CFD）方法,采用k-e湍流模型和组分运输模型对SCR脱硝反应器的氨浓度场进行了数值模拟,并通过实验验证了反应器内氨浓度场数值模拟的准确性,同时,基于响应面法研究了喷氨格栅各结构参数和系统运行参数对SCR脱硝反应器内氨浓度场的影响.结果表明,喷口密度N,开孔率ψ,喷口角度α及入口风速v对氨浓度分布均匀性都存在着一定影响,其中影响的显著性为N>α>v>ψ.而且存在着一组最优的喷氨格栅结构参数和最佳的系统运行参数能够使SCR脱硝反应器内的氨浓度分布不均匀系数达到最优值.在本文研究的参数范围内,喷氨格栅最优的结构参数分别是：r=8个、d=57mm、α=90°,系统最佳的运行参数为v=8.17m/s,此时氨浓度分布不均匀系数为0.0151.     

硫自养反硝化系统运行效能和微生物群落结构研究

启动了单质硫自养反硝化反应器并研究其脱氮性能,通过血清瓶批式实验测定了污泥的反硝化活性,并采用扫描电镜和高通量测序手段揭示了系统内微生物群落结构特征.结果表明,SBR反应器进水NO₃^--N浓度为80mg/L,随水力停留时间由12h逐渐缩短为6h,反应器的自养脱氮性能逐渐增强,稳定期反应器的总无机氮去除率达99.1%,总无机氮去除负荷平均值为0.158kg N/（m³·d）;SBR周期内NO₂^--N浓度最大值为13.3mg/L,NO₃^--N还原为NO₂^--N过程pH值由7.38降低至6.94,NO₂^--N还原为N₂过程pH值基本不变;批式实验结果表明,硫自养反硝化和异养反硝化NO₃^--N去除速率分别为0.515,0.196kg N/（kg VSS·d）,硫自养反硝化污泥NO₂^--N降解速率为0.117kg N/（kg VSS·d）,污泥同时具有自养反硝化和异养反硝化活性;扫描电镜显示,污泥中存在大量的杆状细菌和球状菌;污泥中主要的硫反硝化细菌分别为Thiobacillus、Sulfurimonas和Thermomonas属,其相对丰度分别为14.5%、7.6%和6.0%.     

基质比对ABR厌氧氨氧化工艺脱氮性能的影响

为解决厌氧氨氧化底物去除不彻底导致总氮去除偏低的问题,通过控制不同的进水基质比,对厌氧折流板反应器(ABR)的厌氧氨氧化脱氮性能进行了研究.结果表明,ABR厌氧氨氧化系统最佳进水N_2~O--N/NH+4-N为1.34,此时NH+4-N和N_2~O--N的去除率同时达到99.99%左右,总氮去除率达到峰值为87%,当进水N_2~O--N/NH+4-N从1逐渐降低至0.49和从1.34逐渐提高至1.62时,反应器对NH+4-N和N_2~O--N的绝对去除量较为稳定,NH+4-N或N_2~O--N过量对ABR厌氧氨氧化系统没有产生明显抑制;此外,不同基质比条件下,NH+4-N和N_2~O--N的去除基本在第1隔室完成,基质比变化对ABR各隔室的脱氮效果没有产生显著影响,ABR厌氧氨氧化系统对基质浓度的变化具有较好的稳定性.     

四级串联厌氧反应器对阿卡波糖废渣的减量处理

发酵生产阿卡波糖的过程会产生大量发酵废渣,该废渣处理成本高昂且易造成环境污染。因此,寻找高效环保和低成本的废渣减量处理方法,是目前亟需解决的问题。采用四级串联厌氧反应器对阿卡波糖废渣液进行减量处理,经过启动阶段和负荷提高阶段,共运行68 d。其中,负荷提高阶段增加水解酸化罐作为预处理工艺,两阶段有机负荷分别为1.16,3.32 kg/(m3·d)。结果表明:水解酸化罐作为预处理工艺可提高系统稳定性;系统运行后期可溶性COD去除率达83.3%,平均容积产气率为0.36 m3/(m3·d),废渣中固体物质的去除率达64%,在2—4号罐体底部观察到直径0.8~2 mm的颗粒污泥形成。     

Removal of antibiotics in a parallel-plate thin-film-photocatalytic reactor: Process modeling and evolution of transformation by-products and toxicity

Photocatalytic degradation of sulfamethoxazole(SMX) antibiotic has been studied under recycling batch and homogeneous flow conditions in a thin-film coated immobilized system namely parallel-plate(PPL) reactor. Experimentally designed, statistically evaluated with a factorial design(FD) approach with intent to provide a mathematical model takes into account the parameters influencing process performance. Initial antibiotic concentration, UV energy level, irradiated surface area, water matrix(ultrapure and secondary treated wastewater) and time, were defined as model parameters. A full of 2~5 experimental design was consisted of 32 random experiments. PPL reactor test experiments were carried out in order to set boundary levels for hydraulic, volumetric and defined defined process parameters. TTIP based thin-film with polyethylene glycol + TiO_2 additives were fabricated according to pre-described methodology. Antibiotic degradation was monitored by High Performance Liquid Chromatography analysis while the degradation products were specified by LC–TOF-MS analysis. Acute toxicity of untreated and treated SMX solutions was tested by standard Daphnia magna method. Based on the obtained mathematical model, the response of the immobilized PC system is described with a polynomial equation. The statistically significant positive effects are initial SMX concentration,process time and the combined effect of both, while combined effect of water matrix and irradiated surface area displays an adverse effect on the rate of antibiotic degradation by photocatalytic oxidation. Process efficiency and the validity of the acquired mathematical model was also verified for levofloxacin and cefaclor antibiotics. Immobilized PC degradation in PPL reactor configuration was found capable of providing reduced effluent toxicity by simultaneous degradation of SMX parent compound and TBPs.     

Effects of the support material addition on the hydrodynamic behavior of an anaerobic expanded granular sludge bed reactor

As a support material, zeolite can be used to promote the granulation process due to its high settable property and the ability to retain biomass on its surface. The present paper reports on the influence of zeolite addition on the hydrodynamic behavior of an expanded granular sludge bed reactor (EGSB). Different models were applied to fit the flow pattern and to compare EGSB hydrodynamic performance with and without the addition of zeolite. The experimental data fit the tanks in a series model for zeolite bed height of 5 cm and upflow velocity of 6 m/hr. Higher axial dispersion degree (D/uL) was obtained at lower heights of zeolite. The real hydraulic retention time (HRTr) was increased with both increased zeolite bed height and increased upflow velocity. The short-circuit results for 5 cm of zeolite bed and 6, 8 and 10 m/hr upflow velocity were 0.3, 0.24 and 0.19 respectively, demonstrating the feasibility of using zeolite for a proper hydrodynamic environment to operate the EGSB reactor. The presence of zeolite resulted in the higher percentage values of dead zones, ranging from 12% to 24%. Zeolite addition exerted a positive effect on the hydrodynamics pattern for this technology being advantageous for the anaerobic process because of its possible contribution to better biofilm agglomeration, granule formation and substrate-microorganism contact.     

沼液SBR处理出水养殖螺旋藻

养猪沼液氮磷等营养物质丰富,可作为廉价的螺旋藻培养基,但其成分复杂,尤其是高氨氮等因素严重抑制螺旋藻的生长.采用序批式生物反应器(sequencing batch reactor,SBR)降低沼液中的氨氮浓度,通过改变进水中化学需氧量(chemical oxygen demand,COD)与总氮(total nitrogen,TN)的比值,研究了沼液中的亚硝态氮及硝态氮的保留情况,为螺旋藻生长提供氮源.通过对比螺旋藻在不同工况出水中的生长情况,以及氮元素的保留情况,筛选出最佳SBR工况.摇瓶试验结果表明,当进水COD/TN=3.0,出水中氨氮、硝态氮、亚硝态氮浓度分别为51.2、91.6、213.1 mg·L~(-1),此时螺旋藻具有较快生长速率,产率达到0.084 g·(L·d)~(-1).在此基础之上,通过放大螺旋藻培养规模至120L,研究了螺旋藻在室外大棚中的生长情况及螺旋藻对沼液中氮、磷元素的去除,结果表明螺旋藻在室外依然生长良好,培养10 d后,产率为(0.075±0.003)g·(L·d)~(-1),螺旋藻蛋白含量达到60%左右,养殖出水中氨氮去除率达到99%.     

CSTR和MBR反应器的短程硝化快速启动

为实现短程硝化的快速启动,采用完全混合反应器(CSTR)和膜生物反应器(MBR)进行短程硝化启动性能对比研究,考察两个反应器在启动时间、氮素转化和污泥性能3个方面的差异.结果表明在进水C/N=1,温度为30℃±1℃,pH为7.5~8.0,DO为0.6~1.0 mg·L~(-1),结合缺氧/好氧比为1∶3(15 min∶45 min)和缩短HRT,CSTR和MBR分别运行56 d和44 d成功启动短程硝化,MBR启动周期较短.运行至第14 d、第28 d和第56 d时,CSTR和MBR亚硝累积率平均为51%、66%、89%和50%、71%、93%,硝酸盐氮生成速率(以NO_3~--N/MLVSS计)依次为7.4、4.0、1.7和7.6、3.5、1.0 mg·(g·h)~(-1),MBR在第28 d和第56 d表现出较高的亚硝累积率和较低的NO_3~--N产率,有利于短程硝化的快速启动.整个运行过程中,两个反应器内的亚硝化污泥均呈黄色,SVI在55~110 mL·g~(-1),MLVSS/MLSS稳定在0.6~0.8左右,良好的污泥性能为CSTR和MBR短程硝化的快速启动创造了有利条件.MBR在短程硝化快速启动中展现出更明显的优势.