用热解石墨管和锆＋酒石酸改进剂测定环境样品中锡

本文提出了一种新的混合改进剂（锆＋酒石酸）,能有效消除高氯酸、硝酸以及各种基体的干扰,比较了各原子化温度时理论和实验特征量,使解热石墨管可可能用于石墨炉原子吸收法测定各种环境样品中的锡,准确度和精度优于８％。     

封管法制备有机碳稳定同位素样品存在的问题和改进

有机碳稳定同位素的高精度测定是利用地质样品有机碳同位素研究气候和植被变化等的基础。通过实验发现低有机碳含量样品同位素测定误差相对较大,其中样品收集过程是主要的影响因素之一。本文针对这个问题,主要从杂质气体干扰入手,在一步冷冻分离CO_2和H_2O,或分步冷冻分离CO2和H2O的收集方法,以及改变收样管体积三方面进行条件实验研究,讨论了封管法制备有机碳稳定同位素样品气体收集过程对有机碳稳定同位素组成的影响。结果表明:(1)CO_2气体的纯化收集是封管法制备有机碳稳定同位素样品的一个重要步骤,收集时杂质气体含量越高,对样品有机碳稳定同位素组成的影响越大;(2)在相同的杂质气体背景条件下,与一步冷冻分离CO_2和H_2O的方法相比,分步冷冻CO2和H2O的方法能够显著减小杂质气体对有机碳稳定同位素测定的影响;(3)小体积收样管能够显著提高有机碳稳定同位素样品的离子流强度,进而提高低有机碳含量样品的稳定碳同位素测定精度。     

矩形定径式喉口的设计与应用

针对双文氏管湿法除尘系统一级文氏管喉口存在的问题,开发设计了矩形定径式喉口.该工艺运行周期长,不存在调节翻板卡死问题,不存在溢流盆堵塞问题,喉口使用寿命长,效果良好.     

球墨铸铁管在苏丹炼油厂的应用

论述苏丹炼油厂膨胀土地质条件下给排水管道的设计及管材选用；介绍球墨铸铁管特性和在炼油厂的应用价值     

曝气生物活性炭滤池深度处理垃圾渗滤液的效能研究

为了考察曝气生物活性炭滤池(BACF)深度处理垃圾渗滤液的效能,研究了填料填充度、曝气位置、气水比、水力停留时间和p H等影响因素对滤池去除有机物、氨氮和总氮的影响。结果表明,最佳的工艺运行条件为:填料填充度为80%,底部曝气,气水比为3:1,水力停留时间为8 h,p H为7~8。在最佳工艺条件下运行反应器,COD、氨氮和TN平均去除率分别达到85%、90%和57%,出水可达到实验设定水质要求。BACF具有较强的抗有机负荷能力,进水COD浓度在323至3 000 mg/L之间时,COD去除率稳定在80%。反应器受氨氮冲击负荷影响较大,氨氮进水浓度低于90mg/L时,出水可达到要求。     

Experimental investigation on shock waves generated by pressurized gas release through a tube

An experimental investigation on the flow structures and the strength of shock waves generated by high-pressure gas release through a tube into air was conducted. The results demonstrated that a leading shock wave was generated in front of the compressed gas jet and the shock wave speed increased firstly, then decreased and finally kept constant with an increase of the propagation distance in the tube. The experimentally measured Mach numbers of shock waves were close to those calculated from the theory of ideal shock tube flow. After spouting out of the tube, the normal shock quickly developed into a hemispherical shape. The Mach disk was observed in the under-expanded jet. For high-pressure combustible gas release, the concept of theoretical critical pressure of ignition was introduced and several theoretical critical pressures of common gaseous fuels were obtained.     

A methodology to predict shock overpressure decay in a tunnel produced by a premixed methane/air explosion

A methodology for estimating the blast wave overpressure decay in air produced by a gas explosion in a closed-ended tunnel is proposed based on numerical simulations. The influence of the tunnel wall roughness is taken into account in studying a methane/air mixture explosion and the subsequent propagation of the resulting shock wave in air. The pressure time-history is obtained at different axial locations in the tunnel outside the methane/air mixture. If the shock overpressure at two, or more locations, is known, the value at other locations can be determined according to a simple power law. The study demonstrates the accuracy of the proposed methodology to estimate the overpressure change with distance for shock waves in air produced by methane/air mixture explosions. The methodology is applied to experimental data in order to validate the approach.     

Reduction–melting combined with a Na2CO3 flux recycling process for lead recovery from cathode ray tube funnel glass

With large quantity of flux (Na₂CO₃), lead can be recovered from the funnel glass of waste cathode-ray tubes via reduction–melting at 1000 °C. To reduce flux cost, a technique to recover added flux from the generated oxide phase is also important in order to recycle the flux recovered from the reduction–melting process. In this study, the phase separation of sodium and the crystallization of water-soluble sodium silicates were induced after the reduction–melting process to enhance the leachability of sodium in the oxide phase and to extract the sodium from the phase for the recovery of Na₂CO₃ as flux. A reductive atmosphere promoted the phase separation and crystallization, and the leachability of sodium from the oxide phase was enhanced. The optimum temperature and treatment time for increasing the leachability were 700 °C and 2 h, respectively. After treatment, more than 90% of the sodium in the oxide phase was extracted in water. NaHCO₃ can be recovered by carbonization of the solution containing sodium ions using carbon dioxide gas, decomposed to Na₂CO₃ at 50 °C and recycled for use in the reduction–melting process.     

LD30大口径薄壁无缝管成形工艺

介绍了LD30大直径无缝薄壁筒采用热拉伸坯经变薄旋压成形工艺 ,讨论了其工艺过程 ,工艺参数和应用范围等。     

薄壁钢管弯曲模具设计

分析了薄壁钢管弯曲时产生瘪皱的原因,提出了弯管模具关键参数的设计计算方法,保证了弯管质量.