Characterisation of polycyclic aromatic hydrocarbons in flue gas and residues of a full scale fluidized bed combustor combusting non-hazardous industrial waste

This paper studies the fate of PAHs in full scale incinerators by analysing the concentration of the 16 EPA-PAHs in both the input waste and all the outputs of a full scale Fluidized Bed Combustor (FBC). Of the analysed waste inputs i.e. Waste Water Treatment (WWT) sludge, Refuse Derived Fuel (RDF) and Automotive Shredder Residue (ASR), RDF and ASR were the main PAH sources, with phenanthrene, fluoranthene and pyrene being the most important PAHs. In the flue gas sampled at the stack, naphthalene was the only predominant PAH, indicating that the PAHs in FBC’s combustion gas were newly formed and did not remain from the input waste. Of the other outputs, the boiler and fly ash contained no detectable levels of PAHs, whereas the flue gas cleaning residue contained only low concentrations of naphthalene, probably adsorbed from the flue gas. The PAH fingerprint of the bottom ash corresponded rather well to the PAH fingerprint of the RDF and ASR, indicating that the PAHs in this output, in contrast to the other outputs, were mainly remainders from the PAHs in the waste inputs. A PAH mass balance showed that the total PAH input/output ratio of the FBC ranged from about 100 to about 2600 depending on the waste input composition and the obtained combustion conditions. In all cases, the FBC was clearly a net PAH sink.     

Combined Municipal Solid Waste and biomass system optimization for district energy applications

Municipal Solid Waste (MSW) disposal has been a controversial issue in many countries over the past years, due to disagreement among the various stakeholders on the waste management policies and technologies to be adopted. One of the ways of treating/disposing MSW is energy recovery, as waste is considered to contain a considerable amount of bio-waste and therefore can lead to renewable energy production. The overall efficiency can be very high in the cases of co-generation or tri-generation. In this paper a model is presented, aiming to support decision makers in issues relating to Municipal Solid Waste energy recovery. The idea of using more fuel sources, including MSW and agricultural residue biomass that may exist in a rural area, is explored. The model aims at optimizing the system specifications, such as the capacity of the base-load Waste-to-Energy facility, the capacity of the peak-load biomass boiler and the location of the facility. Furthermore, it defines the quantity of each potential fuel source that should be used annually, in order to maximize the financial yield of the investment. The results of an energy tri-generation case study application at a rural area of Greece, using mixed MSW and biomass, indicate positive financial yield of investment. In addition, a sensitivity analysis is performed on the effect of the most important parameters of the model on the optimum solution, pinpointing the parameters of interest rate, investment cost and heating oil price, as those requiring the attention of the decision makers. Finally, the sensitivity analysis is enhanced by a stochastic analysis to determine the effect of the volatility of parameters on the robustness of the model and the solution obtained.     

Oxygen demand for the stabilization of the organic fraction of municipal solid waste in passively aerated bioreactors

Conventional aerobic waste treatment technologies require the use of aeration devices that actively transport air through the stabilized waste mass, which greatly increases operating costs. In addition, improperly operated active aeration systems, may have the adverse effect of cooling the stabilized biomass. Because active aeration can be a limiting factor for the stabilization process, passive aeration can be equally effective and less expensive. Unfortunately, there are few reports documenting the use of passive aeration systems in municipal waste stabilization. There have been doubts raised as to whether a passive aeration system provides enough oxygen to the organic matter mineralization processes. In this paper, the effectiveness of aeration during aerobic stabilization of four different organic fractions of municipal waste in a reactor with an integrated passive ventilation system and leachate recirculation was analyzed. For the study, four fractions separated by a rotary screen were chosen. Despite the high temperatures in the reactor, the air flow rate was below 0.016 m³/h. Using Darcy’s equation, theoretical values of the air flow rate were estimated, depending on the intensity of microbial metabolism and the amount of oxygen required for the oxidation of organic compounds. Calculations showed that the volume of supplied air exceeded the microorganisms demand for oxidation and endogenous activity by 1.7–2.88-fold.     

Recycling of high purity selenium from CIGS solar cell waste materials

Copper indium gallium diselenide (CIGS) is a promising material in thin film solar cell production. To make CIGS solar cells more competitive, both economically and environmentally, in comparison to other energy sources, methods for recycling are needed. In addition to the generally high price of the material, significant amounts of the metals are lost in the manufacturing process. The feasibility of recycling selenium from CIGS through oxidation at elevated temperatures was therefore examined. During oxidation gaseous selenium dioxide was formed and could be separated from the other elements, which remained in solid state. Upon cooling, the selenium dioxide sublimes and can be collected as crystals. After oxidation for 1 h at 800 °C all of the selenium was separated from the CIGS material. Two different reduction methods for reduction of the selenium dioxide to selenium were tested. In the first reduction method an organic molecule was used as the reducing agent in a Riley reaction. In the second reduction method sulphur dioxide gas was used. Both methods resulted in high purity selenium. This proves that the studied selenium separation method could be the first step in a recycling process aimed at the complete separation and recovery of high purity elements from CIGS.     

Efficiency enhancement in solar air heaters by modification of absorber plate-a review

This paper outlines a complete review on modifications made on the absorber plate of solar air heaters in order to improve the turbulence and heat transfer rate, thereby efficiency. Corrugated sheets, fins, extended surfaces, wire mesh, porous medium, etc., are a few of the modifications used. Most of such alterations in the absorber plate resulted with an increase in efficiency but associated with drawback of increased pumping power due to raising friction factor. Pumping power is considered here as a predominant comparison parameters of various solar air heaters with different absorber plate in terms of effective efficiency.     

Valorisation of used cooking oil sludge by codigestion with swine manure

The addition of lipid wastes to the digestion of swine manure was studied as a means of increasing biogas production. Lipid waste was obtained from a biodiesel plant where used cooking oil is the feedstock. Digestion of this co-substrate was proposed as a way of valorising residual streams from the process of biodiesel production and to integrate the digestion process into the biorefinery concept.Batch digestion tests were performed at different co-digesting proportions obtaining as a result an increase in biogas production with the increase in the amount of co-substrate added to the mixture. Semi-continuous digestion was studied at a 7% (w/w) mass fraction of total solids. Co-digestion was successful at a hydraulic retention time (HRT) of 50 d but a decrease to 30 d resulted in a decrease in specific gas production and accumulation of volatile and long chain fatty acids. The CH₄ yield obtained was 326 ± 46 l/kg VS_feed at an HRT of 50 d, while this value was reduced to 274 ± 43 l/kg VS_feed when evaluated at an HRT of 30 d. However these values were higher than the one obtained under batch conditions (266 ± 40 l/kg VS_feed), thus indicating the need of acclimation to the co-substrate. Despite of operating at low organic loading rate (OLR), measurements from respirometry assays of digestate samples (at an HRT of 50 d) suggested that the effluent could not be directly applied to the soil as fertiliser and might have a negative effect over soil or crops.     

具有变频器的矿井低压漏电保护研究

为了解决移动变电站低压侧为变频器供电时漏电保护装置误动的问题，提出了基于傅式算法的附加直流原理漏电保护新方法。通过理论分析和MATLAB/Simulink仿真，研究了具有变频器的矿井低压供电系统附加直流原理漏电保护，提出由傅式算法分解出采样电压直流分量以反映电缆绝缘水平的保护方法；同时分析了其他因素对直流分量的影响。研究结果表明:变频器对传统附加直流保护整定值有较大影响，易造成漏电保护装置误动且无法实现电缆的在线绝缘监测；所提出的直流分量法能准确测量电缆对地绝缘电阻，且可消除电缆分布电容、变频器载波频率、变频器输出频率等其他因素的干扰；采用该漏电保护方法，可承受变频器投入时对采样电压造成的较大冲击，不必在启动期间解除漏电保护装置，能够消除在此期间存在的人身触电安全隐患。     

Monsanto’s Biotechnology Politics: Discourses of Legitimation

Since the first product became commercially available in 1995, biotechnology has become the fastest growing crop technology, dominating large shares of the global agricultural market. The development of biotechnology, however, has given rise to questions regarding human and ecological safety, culminating in local and global political battles. While researchers interested in biotech politics have focused on areas such as media framing, social movements, and campaign work, less attention has been paid to how the industry has historically promoted and legitimized this swift proliferation. In this study, we conduct a discourse analysis of documents available on live and archived websites to discern the legitimation strategies employed by one important corporate actor, Monsanto. Findings show that for nearly two decades, Monsanto consistently employed discursive resources that concealed details about actors and action, reflected trends among experts in global sustainability discourse, and reshaped narratives to promote itself, products, and biotechnology in general.     

城市电力供应系统公共安全风险评估体系及应用

城市电力供应系统与城市公共安全关系紧密，文章分析了导致城市电力供应系统故障或事故的主要风险因素、事故类型及其风险程度，建立了城市电力供应系统公共安全风险评估体系。利用建立的风险评估体系，对某市电力供应系统的安全性进行了风险评估，同时验证了该体系在城市电力供应系统风险评估中的良好适用性。     

Review of LCA studies of solid waste management systems – Part I: Lessons learned and perspectives

The continuously increasing solid waste generation worldwide calls for management strategies that integrate concerns for environmental sustainability. By quantifying environmental impacts of systems, life cycle assessment (LCA) is a tool, which can contribute to answer that call. But how, where and to which extent has it been applied to solid waste management systems (SWMSs) until now, and which lessons can be learnt from the findings of these LCA applications? To address these questions, we performed a critical review of 222 published LCA studies of SWMS. We first analysed the geographic distribution and found that the published studies have primarily been concentrated in Europe with little application in developing countries. In terms of technological coverage, they have largely overlooked application of LCA to waste prevention activities and to relevant waste types apart from household waste, e.g. construction and demolition waste. Waste management practitioners are thus encouraged to abridge these gaps in future applications of LCA. In addition to this contextual analysis, we also evaluated the findings of selected studies of good quality and found that there is little agreement in the conclusions among them. The strong dependence of each SWMS on local conditions, such as waste composition or energy system, prevents a meaningful generalisation of the LCA results as we find it in the waste hierarchy. We therefore recommend stakeholders in solid waste management to regard LCA as a tool, which, by its ability of capturing the local specific conditions in the modelling of environmental impacts and benefits of a SWMS, allows identifying critical problems and proposing improvement options adapted to the local specificities.