厌氧氨氧化污泥群体感应信号分子检测及影响研究

厌氧氨氧化作为一种新型的脱氮工艺具有很好的应用前景,但厌氧氨氧化污泥富集培养困难.本研究以处理垃圾渗滤液的污泥作为接种污泥,在升流式厌氧污泥反应器(UASB)中启动厌氧氨氧化过程;检测驯化成功的厌氧氨氧化污泥中是否存在群体感应信号分子;并通过添加外源信号分子(cis-11-Methyl-2-dodecenoic acid,DSF和N-acyl-homoserine lactone,AHL),探究信号分子对厌氧氨氧化污泥附着生长能力的影响.结果表明,UASB反应器在运行150 d后,总氮去除率达到80%,菌群结构中厌氧氨氧化菌所占比例超过了20%,成功启动厌氧氨氧化工艺,且厌氧氨氧化污泥中存在低浓度的AHLs信号分子;人为添加3-碳位置取代基为羰基的AHLs(3-oxo-C6-HSL、3-oxo-C8-HSL、3-oxo-C10-HSL和3-oxo-C12-HSL)信号分子均能促进厌氧氨氧化污泥附着生长,而3-碳位置无取代基的AHLs中只有C12-HSL和C6-HSL存在积极影响,C8-HSL、C10-HSL和DSF信号分子对厌氧氨氧化污泥的附着生长能力并没有促进作用.     

海洋污损硅藻附着强度的定量测定

以海洋底栖硅藻新月菱形藻MMDL533作为模型污损物种,利用显微镜-图像分析软件、平行平板流动装置测定了其在羟基化玻璃表面及改性玻璃上的附着性质。研究表明,环境温度为20℃时,新月菱形藻MMDL533在羟基化玻璃表面的附着量最大,在1 h的接触时间后达到87±9/mm2;同时,其附着量随着接触时间延长而变大,并在3 h后达到一个较为稳定的值(110±15/mm2左右);当用水流冲刷后细胞的移除率来表征细胞在特定表面的附着强度时,新月菱形藻MMDL533的附着强度随着表面接触角逐渐增大,并在80°左右达到最大值,然后呈下降趋势。     

液滴撞击超疏水冷表面的反弹/黏附特性对比研究*

为研究液滴撞击超疏水冷表面动力学现象,通过开展去离子水液滴撞击CuO超疏水表面实验,研究表面温度对液滴碰撞后响应方式的影响,分析铺展直径与反弹高度变化规律。结果表明:液滴撞击超疏水冷表面出现反弹与黏附2种响应方式,临界表面温度介于-25 ℃~-20 ℃之间;液滴反弹工况下,表面温度越低,液滴与超疏水冷表面之间接触时间越长,液滴最大反弹高度越小;液滴黏附工况下,随表面温度降低,液滴回缩程度减小,稳定铺展直径增大。研究结果可为表面结冰界面现象与防冰/除冰机理研究提供参考。     

微滤过程中腐殖酸与膜表面黏附特性的试验研究

为了进一步研究微滤过程中腐殖酸对微滤膜的污染机制,通过运用原子力显微镜(AFM),结合自制的PVDF胶体探针考察了不同的pH、离子强度以及钙离子浓度等水质条件下膜-腐殖酸与腐殖酸-腐殖酸之间微观黏附力的变化趋势以及与膜的通量衰减幅度之间的相关性.结果发现,微观黏附力是膜面污染产生的根本原因.由于pH的电性中和以及离子强度的电性屏蔽作用,膜-腐殖酸以及腐殖酸-腐殖酸之间黏附力随着pH的减小或离子强度的增大都呈增大趋势;而随着钙离子浓度的增大,由于少量钙离子的"架桥"作用以及过量时的电性中和作用,两种黏附力先增大后减小.各条件下,膜-腐殖酸与腐殖酸-腐殖酸之间黏附力都呈相同的变化趋势,且与对应污染膜的通量衰减幅度具有正相关性,为更加深入了解膜污染的形成机制提供了一定的理论支持.     

模拟月尘颗粒真空辐射条件下粘附力测试技术研究

目的研究适合于真空辐射条件下颗粒粘附力的测试技术。方法采用调研、分析和计算的方法建立颗粒物粘附力测试方法。首先调研分析大气条件下颗粒粘附力的测试方法,对比分析原子力显微镜测试方法、离心测试方法、静电测试方法、振动分离测试方法以及激光测试方法的适用性。结果现有测试方法并不适用于真空辐射条件下颗粒物粘附力的测试。针对该问题建立了基于颗粒运动的粘附力分析测试方法,通过该方法可获取颗粒带电量和粘附力,给出了基于该方法的试验系统和试验装置的初步设计。结论该测试方法可行,能够满足模拟月尘颗粒粘附力测试的要求。     

Starch-Based Polymers in Extrusion Coating

The starch-based polymers exhibited shear thinning and elastic nature in rheological characterizations. Thin coatings with narrow neck-in could be produced at fairly high extrusion coating line speeds. Adhesion between the starch-based polymers and paperboard was typically weak. Water vapor barrier of starches was very poor. Soft starch grades had a good pinhole resistance and a good heat sealing performance. Brittle nature of starch caused cracking as the coated paperboards were creased.     

Bioabsorbable soy protein plastic composites: Effect of polyphosphate fillers on water absorption and mechanical properties

The use of synthetic and natural bioabsorbable plastics has been severely limited due to their low stiffness and strength properties as well as their strong tendency to absorb moisture. This research focused on the development of bioabsorbable polyphosphate filler/soy protein plastic composites with enhanced stiffness, strength, and water resistance. Bioabsorbable polyphosphate fillers, biodegradable soy protein isolate, plasticizer, and adhesion promoter were homogenized and compression-molded. Physical, mechanical, and water absorption testing was performed on the molded specimens. Results showed improvements in stiffness, strength, and water resistance with increasing polyphosphate filler content up to 20% by weight. Application of a coupling agent produced further mechanical property enhancements and a dramatic improvement in water resistance, interpreted by an interfacial chemical bonding model. Examination of the fracture surfaces of the materials revealed that the addition of the polyphosphate fillers changed the failure mode from brittle to pseudo-ductile. These results suggest that these materials are suitable for many load-bearing applications in both humid and dry environments where current soy protein plastics are not usable.     

深海压力–流速耦合环境下基于灰色系统理论的有机涂层寿命预测研究

目的 建立深海压力–流速耦合环境下有机涂层的寿命预测模型,并预测有机涂层在该环境下的服役寿命。方法 首先针对涂层的湿态附着力变化结果,基于灰色系统理论,建立湿态附着力的GM(1,1)模型。随后再基于耦合环境下的试验结果,建立涂层水传输的扩散模型。最后,在此基础上,利用灰色关联分析方法,计算这2种失效影响因素在涂层失效过程中所占的权重因子,并基于这2个影响因素建立涂层失效的数学模型。结果 经过数学统计验证和试验结果对比验证,该模型精度良好,可靠性高。结论 该模型能够对深海压力–流速耦合环境下有机涂层的寿命进行准确预测。     

Transport and Adhesion of Escherichia coli JM109 in Soil Aquifer Treatment (SAT): One-Dimensional Column Study

Bacteria transport and adhesion experiments under water-saturated and partially saturated conditions were examined over a wide range of ionic strength, from 1 to 100 mM KCl, CaCl₂, and MgCl₂, and at water contents of 0.15 and 0.22 in sand columns packed with three different sands, baked, sterilized, and raw sands in order to investigate the effects of ionic strength, water content, and porous media type on the microbial adhesion in soil aquifer treatment (SAT). Well-characterized Escherichia coli JM109 were used as model bacterial cells in this study. Column study results showed that bacterial deposition rates increased with increasing ionic strength and decreasing water content, and were higher in raw sand columns than those in other sand columns. The Derjaguin–Landau–Verwey–Overbeek (DLVO) theory was applied to experimental results in order to consider the interaction energies between the bacterial cells and collector grains; results revealed that a considerable amount of bacterial cells was weakly deposited onto the solid surfaces in secondary minimum.     

室外钢结构冬季防腐方案

一般防腐涂料施工温度在5 ℃以上,冬季防腐施工气温低至-10 ℃,在制定防腐方案、选择防腐涂料时,通过检测、比较防腐涂料的低温施工性和防腐性能,保证防腐涂料能满足冬季施工的要求.在施工组织中,对防腐涂料进行了性能检验和现场附着力试验,对除锈要求、干膜厚度、表面质量、施工条件进行了严格控制,使整个工程的防腐质量达到要求.