Nitrogen evolution during the co-combustion of hydrothermally treated municipal solid waste and coal in a bubbling fluidized bed

Nitrogen evolution was studied during the co-combustion of hydrothermally treated municipal solid wastes (HT MSW) and coal in a bubbling fluidized bed (BFB). HT MSW blending ratios as 10%, 20% and 30% (wt.%) were selected and tested at 700, 800, 900 °C. Emissions of NO and N₂O from blends were measured and compared with the results of mono-combustion trials. Moreover, concentrations of precursors like NH₃ and HCN were also quantified. The results are summarized as follows: NO emissions were predominant in all the cases, which rose with increasing temperature. The blending of HT MSW contributed to the NO reduction. N₂O emissions decreased with temperature rising and the blending of HT MSW also presented positive effects. At 30% HT MSW addition, both NO and N₂O emissions showed the lowest values (391.85 ppm and 55.33 ppm, respectively at 900 °C). For the precursors, more HCN was detected than NH₃ and both played important roles on the gas side nitrogen evolution.     

Water saving effect on integrated water resource management

This study proposes an improved integrated water resource management (IWRM), in which water conservation was analyzed for the entire water use process. A multi-objective optimization method was applied to optimize the IWRM, which investigated the reduction of freshwater consumption and the total water supply cost. Customer's preference for saving water and an end use analysis (EUA) was applied in the water conservation analysis. Taking Tianjin as the study area, a reduction in customer's economic pressure (EP) was utilized to evaluate the degree of the customer's preference for saving water. The results revealed that agriculture had a greater preference for saving water than other sectors, where as the public had the weakest motivation for saving water. Improving the transportation method could contribute 62.1% of the total water savings in the agriculture sector. The optimization of the IWRM demonstrated that the local freshwater savings would be 21.5%, and the total cost for water supplies would decrease by 13%. However, a government subsidy of 87.5 million Yuan would be needed. Additionally, by analyzing the change in the amount of water savings affected by water price, the appropriate water price increase range was suggested to be 1.5–1.7 times the original price.     

Full-scale blending treatment of fresh MSWI leachate with municipal wastewater in a wastewater treatment plant

Fresh leachate, generated in municipal solid waste incineration (MSWI) plants, contains various pollutants with extremely high strength organics, which usually requires expensive and complex treatment processes. This study investigated the feasibility of blending treatment of MSWI leachate with municipal wastewater. Fresh MSWI leachate was pretreated by coagulation–flocculation with FeCl₃ 2 g/L and CaO 25 g/L, plate-and-frame filter press, followed by ammonia stripping at pH above 12. After that, blending treatment was carried out in a full-scale municipal wastewater treatment plant (WWTP) for approximately 3 months. Different operational modes consisting of different pretreated leachate and methanol addition levels were tested, and their performances were evaluated. Results showed that throughout the experimental period, monitored parameters in the WWTP effluent, including COD (<60 mg/L), BOD₅ (<20 mg/L), ammonium (<8 mg/L), phosphorus (<1.5 mg/L) and heavy metals, generally complied with the Chinese sewage discharged standard. Under the experimental conditions, a certain amount of methanol was needed to fulfill TN removal. An estimation of the operation cost revealed that the expenditure of blending treatment was much lower than the total costs of respective treatment of MSWI leachate and municipal wastewater. The outcomes indicated that blending treatment could not only improve the treatability of the MSWI leachate, but also reduce the treatment cost of the two different wastewaters.     

Targeted Application of Seasonal Load Duration Curves Using Multivariate Analysis in Two Watersheds Flowing Into Lake Houston1

Teague, Aarin, Philip B. Bedient, and Birnur Guven, 2011. Targeted Application of Seasonal Load Duration Curves Using Multivariate Analysis in Two Watersheds Flowing Into Lake Houston. Journal of the American Water Resources Association (JAWRA) 47(3):620‐634. DOI: 10.1111/j.1752‐1688.2011.00529.x Abstract: Water quality is a problem in Lake Houston, the primary source of drinking water for the City of Houston, Texas, due to pollutant loads coming from the influent watersheds, including Spring Creek and Cypress Creek. Statistical analysis of the historic water quality data was developed to understand the source characterization and seasonality of the watershed. Multivariate analysis including principal component, cluster, and discriminant analysis provided a custom seasonal assessment of the watersheds so that loading curves may be targeted for season specific pollutant source characterization. The load duration curves have been analyzed using data collected by the U.S. Geologic Survey with corresponding City of Houston water quality data at the sites to characterize the behavior of the pollutant sources and watersheds. Custom seasons were determined for Spring Creek and Cypress Creek watersheds and pollutant source characterization compared between the seasons and watersheds.     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

ABR-生物接触氧化法处理果汁废水实验分析

厌氧式折流反应器(Anaerobic Baffled Reactor,简称ABR)是一种新型高效厌氧反应器,具有工艺技术简单、建设投资费用低、运行管理方便、固液分离效果好、出水水质好、运行稳定可靠、对有毒物质适应性强等优点,是一种极具开发应用前景的废水生物处理新技术。ABR最大的特点是在反应器中设置上下折流板而在水流方向上形成依次串联的隔室,从而使其中的微生物种群沿长度方向的不同隔室实现产酸和产甲烷相的分离。该反应器具有结构简单,截留污泥能力强,系统处理效果稳定,运行管理方便等优点。分析了ABR及ABR与其它工艺的联合在果汁废水处理方面的应用。     

PLC控制系统在钢渣热焖工艺中的应用

利用PLC控制系统,实现在钢渣热焖工艺中的恒压供水和钢渣热焖定时定量喷水的自动控制要求,具有国际先进水平,取得了良好的经济效益、社会效益和环境效益.     

电化学氢化物发生法处理含锑废水及对锑的回收

采用电化学氢化物发生法对模拟含锑废水进行处理,锑与水电解产生的氢形成氢化物从溶液中脱除,而后收集并加热分解锑化氢得到金属锑.实验表明,在酸性条件下对Sb(Ⅲ)去除效果较好,p H=4时去除率为76.1%.Sb(Ⅲ)与电解水产生的氢结合形成锑化氢从溶液中逸出是溶液中锑去除的最主要途径(回收率为66.2%),电沉积和吸附也对锑的去除做出少量贡献.Sb(Ⅴ)须预还原为Sb(Ⅲ)再氢化进行去除.试用了铅、石墨、钨这3种电解阴极材料,铅电极处理效果最佳.     

三峡蓄水期间汉丰湖消落区营养状态时间变化

为探明三峡蓄水后汉丰湖消落区水质营养状态的变化特征,于2013年10月至2014年2月对水质进行连续观察,测定了水质物理参数、营养盐与叶绿素(Chl-a)的质量浓度.结果表明,水体中营养盐与Chl-a质量浓度的增加,在淹水后营养程度有升高现象,2014年2月与2013年10月相比,TN、TP、高锰酸盐指数与Chl-a质量浓度分别增加了4.7、1.0、0.2、3.27倍,TN、TP质量浓度均超过藻类生长限值,随滞留时间延长易造成水体富营养化,应引起重视.Chl-a单因子评价反映出水质由贫营养向富营养演变.TN/TP结果表明,TN、TP分别在不同时间内制约着藻类的生长;2013年10~12月与2014年2月,藻类生长受TN限制;2014年1月,藻类生长受TP限制.Chl-a与p H、DO、NH+4-N、NO-3-N、TN、高锰酸盐指数及TP呈显著正相关,而与SD、水温呈显著负相关;蓄水期间,水质受到了同一污染源的影响.因子分析结果表明,汉丰湖消落区水质主要受p H、DO、NO-3-N、TN的影响,同时Chl-a、TP、NH+4-N与好氧性有机物的污染不可忽视;在蓄水稳定初期水体具有自净能力,随蓄水滞留时间的延长,水质污染程度整体上呈现逐步恶化的趋势,应加以控制;三峡蓄水期间,南河、东河营养程度相对较高,应加强治理.     

某货车侧翻水污染事件的环境损害评估方法探索

随着我国进入突发水污染事件高发期,面临的水环境形势日益严峻.为了震慑环境污染行为,保证受损的环境资源得到恢复和补偿,量化突发性水污染事件造成的经济损失显得至关重要.本文以重庆市某货车侧翻污染事件为例,构建了一套突发水污染事件环境损害的量化评估方法,并用该方法从财产损害、生态环境资源损害、应急处置行政事务投入费用和调查评估费用这4个方面量化了该事件造成的环境污染损害.