Fe3O4@SiO2-Chitosan的制备及其对水中Cu2+的吸附效能研究

以SiO_2包覆Fe_3O_4,戊二醛为交联剂,交联壳聚糖(Chitosan, CTS),制得Fe_3O_4@SiO_2-Chitosan复合磁性纳米粒子.以Fe_3O_4和Fe_3O_4@SiO_2为对照,采用X射线衍射、透射电镜和傅立叶红外光谱对其进行表征分析,并测定了投加量、pH值、吸附时间和温度等因素对Cu~(2+)吸附效果的影响,从动力学、热力学以及再生回用性能评价等方面对其吸附性能进行了探究.结果表明Fe_3O_4@SiO_2-Chitosan对Cu~(2+)的吸附过程符合准二级吸附动力学模型和Langmuir模型,为自发、放热、优惠型的单分子层化学吸附.在pH为6.0, 298 K下达到最大吸附量154.8 mg·g~(-1),吸附解吸4次后吸附容量变化不大,说明Fe_3O_4@SiO_2-Chitosan具有较高的吸附容量,可作为处理含铜废水和回收铜的高效吸附剂.     

BiOCl/SiO2/Fe3O4复合材料可见光催化去除水中亚甲基蓝

以FeCl_3·6H_2O、FeCl_2·4H_2O、(C_2H_5)_4SiO_4、Bi(NO_3)_3·5H_2O、KCl为主要原料,采用化学共沉淀法和水热法制备了BiOCl/SiO_2/Fe_3O_4光催化剂,并对其进行EDS、TEM、XRD、FT-IR、UV-Vis表征,最后通过亚甲基蓝降解实验,研究了催化剂在合成过程中pH及催化剂投加量对其光催化性能的影响.结果表明,在pH=6、催化剂初始投加量为0.5 g·L~(-1)时,对亚甲基蓝的可见光催化效果最佳,光照120 min后对10 mg·L~(-1)的亚甲基蓝溶液的脱色率达到93.2%.BiOCl/SiO_2/Fe_3O_4经过简单的无水乙醇和水洗后,可高效重复利用4次.综合表明,BiOCl/SiO_2/Fe_3O_4是一种在处理染料废水中具有应用前景的磁性光催化剂.     

From waste hot-pot oil as carbon precursor to development of recyclable attapulgite/carbon composites for wastewater treatment

The utilization of waste products as valuable materials was a technical imperative for waste management. In this study, the cost-effective attapulgite/carbon(APT/C) composite was developed for wastewater treatment using waste hot-pot oil as a carbon precursor through a facile one-step calcination process. The APT/C composite prepared at 300°C exhibited the excellent adsorption capacity and rapid equilibrium rate over a broad p H range for the removal of various pollutants. More importantly, the removal ratios of the composites toward Methyl Violet and tetracycline still remained 77.6% and 60.2% of the initial adsorption capacity after ten adsorption–regeneration cycles via a facile thermal regeneration strategy, respectively.Beyond all doubt, this research provided a feasible and economical way for the sustainable utilization of waste hot-pot oil in wastewater treatment, achieving the concept of disposal waste with waste and recycling.     

炭化压力对编织C/C复合材料致密过程及结构的影响

目的研究不同炭化压力环境对C/C复合材料致密过程及结构的影响。方法通过浸渍/高压炭化工艺在不同炭化压力下制备高温煤沥青炭块及沥青基C/C复合材料,并研究不同炭化压力环境下对其密度和孔隙的影响。结果制备沥青炭的炭化压力由20 MPa增大至60 MPa时,沥青炭体积密度由1.08 g/cm~3增加至1.39g/cm~3,质量比表面积由14.74增加至16.51,开孔率由26.73减少至7.94,孔隙填充效果明显改善,浸渍-炭化的增密效率得到提升。结论在编织C/C材料的致密过程中,压力越大,其孔隙越小,分布越均匀,故产品致密效果越好。     

颗粒冲蚀对注射法制备C/C-ZrC-SiC复合材料 抗烧蚀性能的影响研究

目的采用ZrC和SiC复相陶瓷对C/C复合材料进行改性,研究改性后的复合材料受到颗粒冲蚀破坏的烧蚀行为。方法采用注射法将ZrC和SiC复相陶瓷前驱体引入到等温化学气相渗透法(ICVI)制备的低密度C/C复合材料中,再通过高温热处理、ICVI的方法制备出ZrC和SiC复相陶瓷改性的C/C(C/C-ZrC-SiC)复合材料,随后对制备的复合材料进行高速颗粒冲击实验破坏,并对破坏后的试样进行氧乙炔火焰烧蚀,研究其烧蚀行为。结果改性后的复合材料线冲蚀率和质量冲蚀率分别为253.1μm/s和79.8 mg/s,相较于同孔隙率的C/C复合材料分别降低了49.2%和61%。颗粒冲蚀破坏后C/C-ZrC-SiC复合材料的线烧蚀率和质量烧蚀率分别为4.26μm/s和1.44 mg/s,相比于同孔隙率的C/C复合材料,分别降低了37%和39%。结论由于引入的ZrC和SiC陶瓷相的硬度大于碳基体,C/C-ZrC-SiC复合材料在受到高速颗粒的冲击时,能通过硬质陶瓷相起到抗冲击作用,使得改性后的复合材料抗冲蚀性能大幅度提高。受到颗粒冲蚀破坏后的C/C-ZrC-SiC复合材料内部仍存在超高温陶瓷相,烧蚀过程中能够形成ZrO2骨架结构和SiO2球形颗粒,进而有效保护碳纤维和热解碳基体。     

Processing and Characterization of Short-Fiber Reinforced Jute/Poly Butylene Succinate Biodegradable Composites: The Effect of Weld-Line

Fabrication of complex injection molded parts often involves the use of multiple gates. In such situations, polymer melts from different gates meld to form the molded part (weld line). This paper reports on the fabrication and characterization of the mechanical and morphological properties of short fiber reinforced jute/poly butylene succinate (PBS) biodegradable composites. The effect of a dual gated mold in the fabrication of welded specimens was a key focus of the investigation. It was observed that incorporation of jute fiber (10 wt%) conferred drastic changes on the stress–strain properties of the matrix as the elongation at break (EB), dropped from 160% in the matrix to just 10% in the composite. The tensile strength of the composite was lower than that of the matrix. However, it is noteworthy that the tensile modulus of the composite increased. Bending test also revealed that both bending strength and modulus increased with the incorporation of jute. Morphological studies of the tensile fracture surface using SEM revealed two types of failure mode. Ductile failure was indicated by plastic deformation at the initiation of fracture followed by brittle failure. The good interfacial bonding indicated between jute and PBS was attributed to positive interaction between the two polar polymers. A comparison of the non-weld and weld-line samples revealed that the weld-line composites have better mechanical integrity than the corresponding polymer matrix with weld line. The results also revealed that elongation at break and toughness are most sensitive to the presence of the weld-line whereas flexural properties are least sensitive.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

埕岛油田海底管道漏磁检测与安全评估

提出了埕岛油田海底管道内缺陷漏磁检测需解决的主要问题,研发了325 mm管道内缺陷漏磁检测装置,确定了海底管道漏磁检测工艺流程,配套了管道检测发射装置、接受装置等相关设施,实现了海底管道的漏磁检测、缺陷分析和安全评估。