全文获取类型
收费全文 | 179篇 |
免费 | 58篇 |
国内免费 | 30篇 |
专业分类
安全科学 | 61篇 |
废物处理 | 18篇 |
环保管理 | 17篇 |
综合类 | 130篇 |
基础理论 | 5篇 |
污染及防治 | 32篇 |
评价与监测 | 2篇 |
社会与环境 | 1篇 |
灾害及防治 | 1篇 |
出版年
2024年 | 1篇 |
2023年 | 12篇 |
2022年 | 10篇 |
2021年 | 8篇 |
2020年 | 10篇 |
2019年 | 10篇 |
2018年 | 7篇 |
2017年 | 10篇 |
2016年 | 15篇 |
2015年 | 12篇 |
2014年 | 9篇 |
2013年 | 26篇 |
2012年 | 14篇 |
2011年 | 7篇 |
2010年 | 8篇 |
2009年 | 4篇 |
2008年 | 3篇 |
2007年 | 8篇 |
2006年 | 10篇 |
2005年 | 17篇 |
2004年 | 11篇 |
2003年 | 15篇 |
2002年 | 6篇 |
2001年 | 9篇 |
2000年 | 2篇 |
1999年 | 5篇 |
1998年 | 4篇 |
1997年 | 4篇 |
1996年 | 1篇 |
1995年 | 3篇 |
1994年 | 2篇 |
1993年 | 2篇 |
1989年 | 1篇 |
1987年 | 1篇 |
排序方式: 共有267条查询结果,搜索用时 31 毫秒
211.
212.
213.
214.
215.
John W. Leung Alam Sundaram 《Journal of environmental science and health. Part. B》2013,48(5-6):653-682
Abstract Dipel® 8AF, a commercial formulation of Bacillus thuringiensis (B.t.) was sprayed undiluted at 30 BIU in 1.8L/ha over a block B1, and sprayed after dilution with water at 30 BIU in 6.2 L/ha over another block B2 in an oak forest infested with the gypsy moth (Lymantria dispar L.) in southeastern Ontario, Canada. Spray was applied in May 1987 using a Cessna 188 Agtruck aircraft equipped with four Hicronair® AU4000 atomizers. Droplet sizes were measured at mid‐canopy level of oak trees and at ground level using cylindrical Kromekote® cards. Deposit per unit area was assessed on aluminum oak leaves. At the lower volume rate of 1.8 L/ha, spray droplets were smaller and droplets/cm2 were lower on the cylindrical Kromekote cards in B1 than those obtained in B2 which received the higher volume rate of 6.2 L/ha. The average deposit per unit area of the aluminum oak leaves, expressed in nL of the spray volume per cm2 surface area, was also correspondingly lower in B1 than in B2. This was attributed to the higher volume rate of spray application used in B2 than in B1, which resulted in larger droplets and a greater volume deposit/cm2 in B2. 相似文献
216.
目的 通过实验室模拟不同环境条件的降雨试验,研究金属材料表面的积冰行为。方法 基于数值仿真分析,选择适合积冰的放置方法,针对金属材料开展降雨环境模拟试验。以水温、环境温度、试件温度、喷淋高度、试件厚度为基本参数,分析实验室模拟降雨环境下不同金属材料表面的积冰程度。结果 仿真分析可以得到理想状态的理论分析结果。当水温为5℃,环境温度为–1.5、–3℃时,在高度3、4 m喷淋30 min后,除10 mm厚度7075铝合金外,被试材料积冰均难以达到6 mm。当水温不变,环境温度为–6℃时,在高度3、4 m喷淋30 min后,部分被试材料达到6 mm积冰。当试验环境温度不变而水温降低时,水温与积冰呈较明显的递增趋势。在其他试验条件相同的情况下,环境温度为–9℃时,所有被试材料积冰均达到6 mm以上。结论 调整各项试验环境参数可控制金属材料表面的积冰程度。在相同水温、喷淋高度和材料厚度的条件下,随着环境温度的降低,积冰增加,4 m喷淋高度的积冰优于3 m喷淋高度。可将试验数据与理论分析数据相融合,使用理论分析结果进行方向预测,利用环境模拟试验数据对其进行修正。 相似文献
217.
以新疆天山水泥股份有限公司一分厂1水泥磨除尘系统技术改造为实例,阐述了获1993年国家环保最佳实用技术推广的LCPM型高压离线侧喷脉冲袋除尘器在水泥磨系统的应用及产生的效果。 相似文献
218.
219.
220.