有关斜管沉淀池的上升流速讨论

文章从理论上了分析斜管沉淀池上升流速对沉淀池处理效果的影响,及原水特性与斜管沉淀池上升流速取值的关系。讨论分析斜管沉淀池设计时,应根据原水特性不同选择不同的斜管沉淀池上升流速。     

Effect of oxide-based fluxes on mechanical and metallurgical properties of Dissimilar Activating Flux Assisted-Tungsten Inert Gas Welds

Present investigation is to study the “Effect of Activating Fluxes on Mechanical and Metallurgical Properties of Dissimilar Activated Flux-Tungsten Inert Gas Welds”. Effect of current, welding speed, joint gap and electrode diameter on weld bead dimensions on 6 mm thick dissimilar weld between carbon steel to stainless steel, was studied under Activated Flux-Tungsten Inert Gas Welding process. During this investigation three different types of oxide powders were used-TiO₂, ZnO and MnO₂. After welding samples were subject to mechanical testing, in addition to characterization via micro hardness and microstructures of Normal Tungsten Inert Gas Welds and Activated Flux-Tungsten Inert Gas Welds. Activating fluxes TiO₂ and ZnO are effective fluxes for Activated Flux-Tungsten Inert Gas Welding of dissimilar weld between CS to SS. Highest depth/width (D/W) ratio reported under TiO₂ and ZnO fluxes compare to Normal-Tungsten Inert Gas Welds. Lowest angular distortion was observed under TiO₂ flux compare to Normal-Tungsten Inert Gas Welds. Mechanical properties, Joint Efficiency of Activated Flux-Tungsten Inert Gas Welds are higher than normal-Normal Tungsten Inert Gas Welds. Tensile Test specimens of both the processes failed from the parent metal (carbon steel side). Carbon migration from CS to SS, had occurred which led to failure of weld joints from CS side.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

45~#钢在西双版纳大气环境下的腐蚀研究

目的研究西双版纳热带雨林地区大气环境下材料的初期腐蚀行为。方法使用45#碳钢在西双版纳大气环境下进行1年的大气暴露腐蚀试验,并利用质量损失分析、SEM、XRD和FTIR等技术,分析45#碳钢在西双版纳大气环境下暴露1年的腐蚀行为。结果 45#碳钢的腐蚀产物以γ-FeOOH,Fe(OH)3和Fe3O4为主,并有少量的α-FeOOH。结论西双版纳大气环境腐蚀性为C2级。在暴露1年的时间内,锈层化学稳定性随试验时间的延长逐渐增强,对基体的保护性逐渐加大。     

不同构造措施的钢管混凝土边框钢板剪力墙抗震性能试验研究

钢管混凝土边框钢板剪力墙是一种新型抗震剪力墙,为了比较不同构造措施对该新型剪力墙抗震性能的影响,进行了3个剪跨比为1.5的钢管混凝土边框钢板剪力墙低周反复荷载试验.其中,试验模型1为墙体钢板与边框柱钢管焊接,试验模型2为墙体钢板与边框柱钢管螺栓连接,试验模型3为墙体钢板开孔并与边框柱钢管焊接.通过试验研究,比较了各剪力...     

钢渣吸附-微波降解法处理碱性品红废水

研究了钢渣对碱性品红染料的吸附性能、影响因素以及微波对吸附在钢渣-焦炭上的染料的降解作用。实验表明,在中性条件下,钢渣对碱性品红具有优良的吸附性能,饱和吸附量可达到42．4mg／g。以钢渣处理质量浓度为100mg/L的碱性品红溶液,当固液质量比为1：50、振荡吸附1h后,染料溶液脱色率达97％。实验还表明,焦炭可吸收微波产生高温,用钢渣-焦炭混合物（质量比1：1）吸附染料后,以微波辐照可使物料达到665℃的高温,吸附的染料降解。吸附剂再生后重复使用4次,脱色率都达到95％以上。     

钢渣预处理含铬废水及其废渣与铬渣的固化

用钢渣对含铬废水进行预处理,探讨了钢渣粒度、用量、废水pH值和添加硫酸亚铁还原剂的影响.结果表明,经硫酸亚铁还原处理后再用钢渣处理比单纯用钢渣处理的效果明显提高,采用钢渣/总铬质量比为40的100目钢渣处理经硫酸亚铁还原后的含铬废水,总铬和Cr6 去除率分别达79%和84%,采用钢渣柱进行的两级淋滤实验进一步表明该方法可作为工业上含铬废水处理的预处理段.处理后的废钢渣同工业铬渣一起进行水泥固化,标准养护20 d后固化体表面Cr6 浸出率、破碎至5 mm粒径以下和酸雨淋溶下的浸出液Cr6 浓度均符合安全标准,可作为普通建材或进行填埋处置.     

CDM Project Activities in China＇s Iron and Steel Industry：Current Status,Barriers and Development Strategies

China is now facing huge pressure from both the domestic concern of energy security and the global community's call for emission reduction commitment. As one of the major energy consumers and greenhouse gas emitters, China's iron and steel industry has a huge clean development mechanism (CDM) potential. This article both quantitatively and qualitatively analyzes the current status of CDM project activities in the iron and steel industry in China, including characteristics of approved project types, applicable methodologies, and potential technology fields. From the perspective of project implementation, the article summarizes development barriers such as high investment risk, difficulty in project identification, strict requirements on PPDs, long registration waiting time, and etc. Policy suggestions are also put forwarded to help better promote the development of CDM projects in the iron and steel industry.     

Detection of DDT and its metabolites in two estuaries of South China using a SPME-based device: First report of p,p′-DDMU in water column

A solid-phase microextration-based sampling method was employed to determine the concentrations of 1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) and its metabolites, 1,1-dichloro-2,2-bis(p-chlorophenyl)ethane (DDD), 1,1-dichloro-2,2-bis(p-chlorophenyl)ethene (DDE) and 1-chloro-2,2-bis(p-chlorophenyl)ethene (DDMU), in two estuarine bays, Daya Bay and Hailing Bay, of South China. Six DDT components including p,p′-DDT, o,p′-DDD, p,p′-DDD, o,p′-DDE, p,p′-DDE, and p,p′-DDMU were detected in Hailing Bay, while only p,p′-DDD was found in Daya Bay. p,p′-DDD was the most abundant DDT component in both bays, sharply different from the previous finding in the water column of the Palos Verdes Shelf, California, USA that p,p′-DDE was prevalent. In addition, the occurrence of p,p′-DDMU (with a range of 0.047-0.21 ng/L in Hailing Bay) has not been reported around the globe, and its presence in our study region appeared to stem from dehydrochlorination of p,p′-DDD, favored under aerobic conditions, but further investigations are clearly needed to confirm the mechanism for generation of DDMU in estuarine environments.     

废钢铁切割加工烟尘的治理

介绍了氧-乙炔火焰切割加工废钢铁产生的烟尘治理系统的设计和系统设备选型,重点介绍了烟尘捕集罩的设计和除尘器、电磁脉冲阀、风机的选型和PLC自动控制以及系统实际运行效果,为废钢铁加工企业治理污染提供一套简单、经济、实用的除尘系统作参考.