单轴应力对煤自燃特性参数和导热系数的影响研究

为探究单轴应力作用下煤氧化和传热特性,利用自制荷载加压煤自燃特性参数测定装置对炉体内长焰煤煤样进行程序升温。结合程序升温过程中煤临界温度Tc和Tg,对其进行阶段划分:阶段1为30℃~Tc;阶段2为Tc~Tg。计算了不同单轴应力下2个阶段煤表观活化能和平均耗氧速率。根据能量守恒得出程序升温过程煤导热系数随温度的变化,进一步分析煤导热系数与单轴应力的关系。结果表明:阶段1单轴应力为4 MPa时为临界轴压,煤表观活化能最大,平均耗氧速率最小;阶段2煤表观活化能和平均耗氧速率随单轴应力增大均呈抛物线变化,单轴应力为2.7 MPa时为临界轴压,煤表观活化能最大,平均耗氧速率最小;阶段1和2煤导热系数随温度升高均先减小后增大,并且煤导热系数随单轴应力增大呈三次函数变化。     

Using multivariate regression modeling for sampling and predicting chemical characteristics of mixed waste in old landfills

Municipal solid waste landfills pose a threat on environment and human health, especially old landfills which lack facilities for collection and treatment of landfill gas and leachate. Consequently, missing information about emission flows prevent site-specific environmental risk assessments. To overcome this gap, the combination of waste sampling and analysis with statistical modeling is one option for estimating present and future emission potentials. Optimizing the tradeoff between investigation costs and reliable results requires knowledge about both: the number of samples to be taken and variables to be analyzed.This article aims to identify the optimized number of waste samples and variables in order to predict a larger set of variables. Therefore, we introduce a multivariate linear regression model and tested the applicability by usage of two case studies. Landfill A was used to set up and calibrate the model based on 50 waste samples and twelve variables. The calibrated model was applied to Landfill B including 36 waste samples and twelve variables with four predictor variables.The case study results are twofold: first, the reliable and accurate prediction of the twelve variables can be achieved with the knowledge of four predictor variables (Loi, EC, pH and Cl). For the second Landfill B, only ten full measurements would be needed for a reliable prediction of most response variables. The four predictor variables would exhibit comparably low analytical costs in comparison to the full set of measurements. This cost reduction could be used to increase the number of samples yielding an improved understanding of the spatial waste heterogeneity in landfills.Concluding, the future application of the developed model potentially improves the reliability of predicted emission potentials. The model could become a standard screening tool for old landfills if its applicability and reliability would be tested in additional case studies.     

青冰滩冰川水文特征初步分析

通过对青冰滩冰川的综合考察,对该地区2008-08-01日至08-31日的水文、气象以及水环境进行了连续观测。结果表明:冰川表面大量覆盖冰碛增加了冰川表面的反射率,加速了冰川消融;整个8月日均气温在8℃以下,气温的日较差较大,冰川消融期的降水以降雪和冰雹为主;冰川融水的电导率和溶解性固体相关系数可达0.98,两者与气温的相关度也可达到0.8以上。     

Toxicological characterization of the landfill leachate prior/after chemical and electrochemical treatment: A study on human and plant cells

In this research, toxicological safety of two newly developed methods for the treatment of landfill leachate from the Piškornica (Croatia) sanitary landfill was investigated. Chemical treatment procedure combined chemical precipitation with CaO followed by coagulation with ferric chloride and final adsorption by clinoptilolite. Electrochemical treatment approach included pretreatment with ozone followed by electrooxidation/electrocoagulation and final polishing by microwave irradiation. Cell viability of untreated/treated landfill leachate was examined using fluorescence microscopy. Cytotoxic effect of the original leachate was obtained for both exposure periods (4 and 24 h) while treated samples showed no cytotoxic effect even after prolonged exposure time. The potential DNA damage of the untreated/treated landfill leachate was evaluated by the comet assay and cytokinesis-block micronucleus (CBMN) assay using either human or plant cells. The original leachate exhibited significantly higher comet assay parameters compared to negative control after 24 h exposure. On the contrary, there was no significant difference between negative control and chemically/electrochemically treated leachate for any of the parameters tested. There was also no significant increase in either CBMN assay parameter compared to the negative control following the exposure of the lymphocytes to the chemically or electrochemically treated landfill leachate for both exposure periods while the original sample showed significantly higher number of micronuclei, nucleoplasmic bridges and nuclear buds for both exposure times. Results suggest that both methods are suitable for the treatment of such complex waste effluent due to high removal efficiency of all measured parameters and toxicological safety of the treated effluent.     

Indirect measurements of field-scale hydraulic conductivity of waste from two landfill sites

Management and prediction of the movement and distribution of fluids in large landfills is important for various reasons. Bioreactor landfill technology shows promise, but in arid or semi-arid regions, the natural content of landfilled waste may be low, thus requiring addition of significant volumes of water. In more humid locations, landfills can become saturated, flooding gas collection systems and causing sideslope leachate seeps or other undesirable occurrences. This paper compares results from two different approaches to monitoring water in waste. At the Brock West Landfill in eastern Canada, positive pore pressures were measured at various depths in saturated waste. The downward seepage flux through the waste is known, thus the vertical saturated hydraulic conductivity of the waste at this landfill was determined to be 3 × 10(-7)cm/s. By comparison, the Spadina Landfill in western Canada is predominantly unsaturated. The infiltration of moisture into the waste was measured using moisture sensors installed in boreholes which determined arrival time for moisture fronts resulting from major precipitation events as well as longer-term change in moisture content resulting from unsaturated drainage during winter when frozen ground prevented infiltration. The unsaturated hydraulic conductivity calculated from these data ranged from approximately 10(-6)cm/s for the slow winter drainage in the absence of significant recharge to 10(-2)cm/s or higher for shallow waste subject to high infiltration through apparent preferential pathways. These two very different approaches to field-scale measurements of vertical hydraulic conductivity provide insight into the nature of fluid movement in saturated and unsaturated waste masses. It is suggested that the principles of unsaturated seepage apply reasonably well for landfilled waste and that the hydraulic behavior of waste is profoundly influenced by the nature and size of voids and by the degree of saturation prevailing in the landfill.     

ESTIMATING TRANSMISSIVITY AND HYDRAULIC CONDUCTIVITY OF CHICOT AQUIFER FROM SPECIFIC CAPACITY DATA1

ABSTRACT: Specific capacity data obtained from Well Construction reports which are available from USGS offices, can provide useful estimates of tranamissivity (T), and hydraulic conductivity (K), of an aquifer. The Chicot Aquifer in Louisiana is one of the largest sources of fresh ground water in North America. Hydrologic data collected for the Chicot Aquifer indicate that specific capacity tests can be used in estimating local and regional values for T and K, if the Cooper-Jacob equation for transient flow is used with proper corrections for well loss and partial penetration. Where full scale pumping test data are scarce, specific capacity test data that are adequately distributed spatially can be used to map changes in T and K values and can be summarized statistically to indicate applicable regional values. A computer program called “TGUESS” which is available from International Ground Water Modeling Center, Holcomb Research Institute, was used in this study. The contour maps for T and K values are prepared for different well depth intervals to avoid wide variation of values.     

Utilization of cement kiln dust (CKD) in cement mortar and concrete—an overview

Solid waste management is one of the major environmental concerns around the world. Cement kiln dust (KKD), also known as by-pass dust, is a by-product of cement manufacturing. The environmental concerns related to Portland cement production, emission and disposal of CKD is becoming progressively significant. CKD is fine-grained, particulate material chiefly composed of oxidized, anhydrous, micron-sized particles collected from electrostatic precipitators during the high temperature production of clinker. Cement kiln dust so generated is partly reused in cement plant and landfilled. The beneficial uses of CKD are in highway uses, soil stabilization, use in cement mortar/concrete, CLSM, etc.Studies have shown that CKD could be used in making paste/mortar/concrete. This paper presents an overview of some of the research published on the use of CKD in cement paste/mortar/concrete. Effect of CKD on the cement paste/mortar/concrete properties like compressive strength, tensile strength properties (splitting tensile strength, flexural strength and toughness), durability (Freeze–thaw), hydration, setting time, sorptivity, electrical conductivity are presented. Use of CKD in making controlled low-strength materials (CLSM), asphalt concrete, as soil stabilizer, and leachate analysis are also discussed in this paper.     

百口泉地下水电导率与溶解性总固体相关性讨论

由于溶解性总固体的测定较为复杂,平行性、稳定性差,而电导率的测定简便、迅速,重现性、稳定性好,若二者相关关系显著,可通过测定电导率,按一定的比例推算水中溶解性总固体的量。通过对百口泉地下水的溶解性总固体与电导率的相关性的监测、分析,经统计检验,线性关系显著,其比值范围在065～076,均值为07,即百口泉地下水的电导率1μs/cm相当于070mg/L的溶解性总固体。     

基于野外数据建立大型底栖动物电导率水质基准的可行性探讨

科学合理地设定水质基准是水生生物保护和水生态系统恢复的基础。水体电导率数值的高低由溶解于其中的各种阴阳离子的浓度所决定,而较多的研究也证明电导率能够显著地影响水生生物类群,特别是大型底栖动物物种存活和群落结构的稳定性。离子组成的复杂性,导致无法开展基于室内实验的水生生物电导率基准值的推导。本文借鉴美国环境保护局基于野外调查数据建立电导率基准值的方法,采用流行病学打分方法,分别从电导率是否对大型底栖动物敏感物种存在毒性效应、人为干扰的增强是否会通过电导率产生毒性作用,以及其他环境因子是否对电导率基准值的制定产生影响3个方面,探讨了基于野外数据建立我国电导率基准的可行性。研究区域为辽河流域的浑河及太子河,野外调查数据采集于2009年8月至2010年5月。研究结果表明,电导率的升高显著降低了大型底栖动物敏感物种的出现频率。通过分析研究区域土地利用方式同电导率之间的相关性,证明了农业和城镇建设用地比例的增加显著地增加了水体中电导率的数值。对有可能引起物种消失的其他环境因子进行分析,结果表明电导率是引起大型底栖动物消失的主要原因。综合以上结果,基于野外调查数据来建立大型底栖动物电导率基准值是可行的,为我国水质基准的研究提供了新的思路和方法。     

SiO2气凝胶隔热性能的影响因素研究

目的 在不同热流条件下,通过调整SiO2气凝胶的孔隙率、涂层厚度等,以满足合适的隔热要求。方法 针对中短程飞行器飞行时外壁面承受短时高热流的特点,在分析孔隙率对SiO2气凝胶热导率影响规律的基础上,通过数值仿真研究不同气凝胶孔隙率、气凝胶厚度及热流作用下的温度响应。结果 得到了不同条件下满足隔热要求的气凝胶最小厚度,以及气凝胶表面的最高温度。高温情况下,气凝胶孔隙率为96%时,有效热导率最低,孔隙率超过96%时,隔热性能变差。结论 当飞行器内壁面温度满足要求时,增大气凝胶的孔隙率,则需要减小气凝胶的厚度,相应的气凝胶表面温度会升高,但升幅很小。当飞行器外壁面承受长时间大热流时,仅调整气凝胶的厚度和孔隙率不能达到结构的隔热要求。