爆炸冲击波作用下靶板的塑性大变形响应研究

对四边约束方形靶板 ,在爆炸冲击波作用下的塑性大变形响应情况 ,进行了理论分析与试验研究。运用能量守恒的方法 ,同时考虑试验过程中靶板的边界约束条件 ,得到了四边约束方形靶板在爆炸冲击波作用下发生塑性大变形时挠度的半经验公式。理论计算与试验结果吻合性较好 ,这种方法可应用于板结构在爆炸冲击波作用下的毁伤或防护方面的工程预测     

城市地铁暗挖施工地层变形机理及控制实践

笔者结合深圳地铁一期工程的某些暗挖标段工程及地质条件 ,在土层性质试验研究的基础上 ,深入分析了地层大变形机理及其主要影响因素 ,由此确定了地层大变形控制的原则和技术措施。在施工中 ,应用地层变形控制原则及相应的综合技术措施后 ,使地层变形大幅度降低 ,满足了地表环境保护的要求 ,取得了预期的效果     

特大型煤和瓦斯突出的地质条件及其成因

特大型煤和瓦斯突出危害极大，具有独特的发生条件，应专门研究。在全国９９ 次特大型煤和瓦斯突出详细研究的基础上，总结了特大型突出的一般特征及发生的地质和采矿条件，并给出了南桐矿区的几个临界值。对特大型突出地质条件的成因进行了较深入的探讨，提出了防止特大型突出的几点建议     

官方媒体参与下不同风险感知群体竞争模型及其演化规律

为识别公众风险感知的演化规律和官方媒体参与的作用机制，首先，根据公众的行为表现划分不同风险感知群体，并分析群体间的相互竞争和官方媒体的扰动作用；然后，通过扩展Lotka Volterra模型建立群体间的相互竞争模型；在此基础上，通过推导模型平衡点及其稳定性分析模型演化规律；最后，运用数值仿真考查了官方媒体的参与对模型演化的影响。研究结果表明:模型演化具有3种结果情景，官方媒体参与能够显著改变模型演化的速度和结果。     

Nitrogen evolution during the co-combustion of hydrothermally treated municipal solid waste and coal in a bubbling fluidized bed

Nitrogen evolution was studied during the co-combustion of hydrothermally treated municipal solid wastes (HT MSW) and coal in a bubbling fluidized bed (BFB). HT MSW blending ratios as 10%, 20% and 30% (wt.%) were selected and tested at 700, 800, 900 °C. Emissions of NO and N₂O from blends were measured and compared with the results of mono-combustion trials. Moreover, concentrations of precursors like NH₃ and HCN were also quantified. The results are summarized as follows: NO emissions were predominant in all the cases, which rose with increasing temperature. The blending of HT MSW contributed to the NO reduction. N₂O emissions decreased with temperature rising and the blending of HT MSW also presented positive effects. At 30% HT MSW addition, both NO and N₂O emissions showed the lowest values (391.85 ppm and 55.33 ppm, respectively at 900 °C). For the precursors, more HCN was detected than NH₃ and both played important roles on the gas side nitrogen evolution.     

成都市污染边界层高度的演变特征分析

基于2014年1月21日至2月5日成都市人民南路四段逐时PM_(2.5)质量浓度、大气能见度资料以及同期Mie散射激光雷达探测数据,遵循消光系数与细颗粒物质量浓度之间的关系,探讨污染边界层高度的演变特征。结果表明:污染时段内的污染边界层高度偏低,平均为221m;污染边界层高度与地面PM_(2.5)浓度的变化具有明显相关性,但污染边界层高度改变在前,地面PM_(2.5)浓度响应在后;污染边界层高度的日变化表现为单峰单谷型,峰值和谷值分别出现在08:00时和14:00时前后。     

厌氧-准好氧联合型生物反应器填埋场产气规律的研究

通过将厌氧型生物反应器填埋场（ANBL）和准好氧矿化垃圾生物反应床（SAARB）串联,组成新型的厌氧-准好氧联合型生物反应器填埋场（AN-SABL）,研究其产气速率、产气量以及产气组分的变化规律,以期为填埋气体的收集、利用和处理提供理论依据.实验表明,AN-SABL中的厌氧填埋单元的产气受到了抑制,其中ANBL2号单元和ANBL3号单元的产气率分别为49 L.kg-1和39 L.kg-1,仅占ANBL1号的94.2%和75.0%,但提高回灌频率,能促进厌氧填埋单元的产气,其甲烷含量最大值可达到62.67%;ANBL夏季产气速率和产气量明显高于冬季,并以12 h为周期交替出现产气高峰;此外,AN-SABL能够促进其厌氧单元的硝化和反硝化作用,N2O的含量受季节和填埋场类型影响显著,其变化范围在0.001 7%～4.017 9%之间.ANBL的累积产气量在初始调整阶段呈对数增长,过渡酸化阶段呈线性增长,酸化产甲烷阶段呈指数增长.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

核电厂换料水池底部密封结构密封元件的性能分析

目的研究某核电厂换料水池底部密封结构中密封元件的性能。方法利用有限元分析软件ANSYS,采用超弹单元建立换料水池底部密封结构密封元件的二维轴对称模型,并运用接触单元模拟密封接触界面进行计算分析。结果经计算得到换料水池底部密封结构密封元件的预紧力-变形量曲线。结论计算结果为分析换料水池底部密封结构密封试验的泄漏原因提供了理论依据,同时也为工程中密封元件预紧力的确定提供了较有价值的参考。     

预腐蚀LY12CZ铝合金的疲劳寿命预测模型

目的研究铝合金预腐蚀疲劳的寿命评估模型。方法利用损伤力学模型,建立预腐蚀构件疲劳寿命预测模型,并利用LY12CZ铝合金进行预腐蚀疲劳的验证性实验。结果利用损伤力学建立的模型所得到的预腐蚀铝合金试件的疲劳寿命与实验结果吻合程度良好。结论基于损伤力学的铝合金预腐蚀疲劳寿命预测模型合理有效。