爆炸冲击波作用下圆形通风设施的动态破坏特性

为了研究瓦斯爆炸对通风设施造成的严重破坏及其导致的通风系统紊乱与灾情迅速扩展问题,基于LS-DYNA有限元软件,模拟研究巷道中瓦斯爆炸冲击波作用下圆形通风设施的动态破坏特性,分析应力、应变、速度、位移的动态特征及其破坏过程,并对圆形通风设施动态破坏机理进行初步探索。研究结果表明:爆炸冲击波作用下,圆形通风设施正、反面出现压应力与拉应力分布圆环,且压应力与拉应力峰值处于在外部受约束边界径向圆环附近区域与圆心位置,应变、速度和位移最大值均分布在次区域;爆炸冲击波作用下,通风设施表面形成多圈的正向和反向的应变相互交替,呈现W型的褶皱变形;爆炸冲击波作用下,环向裂纹集中在受约束的边界区域附近,发生脆性破坏,其他区域会出现较多的径向裂纹,可发生韧性破坏,整个断裂过程是脆性与韧性断裂的混合型断裂。     

基于人工神经网络的气体泄爆最大超压预测研究

为解决传统经验公式在预测气体泄爆中最大超压出现时的较大偏差或过于保守的问题,提出使用人工神经网络预测气体泄爆最大超压。基于124组实验数据,采用BP与RBF神经网络,通过优化算法计算与迭代循环对泄爆样本中的影响因素进行降维与选择,并确定2类神经网络本身在学习与计算气体泄爆样本时的相关参数。结果表明:PCA（主成分分析法）在当前样本条件下的降维效果较差,而通过迭代对比确认气体泄爆样本中的5类特征全部保留时神经网络的训练模拟效果最好;通过对124组实验数据进行随机挑选训练集与测试集的训练模拟结果发现,神经网络对气体泄爆中最大超压的预测效果较好;通过对比Molkov提出的和经Fakandu等改进的NFPA 68经验公式以及2类神经网络的预测结果表明,神经网络相比于传统气体泄爆经验公式具有明显优势。     

缝洞型管道瓦斯爆炸特性数值模拟研究

为探究采空区遗煤、松散破碎岩块对瓦斯爆炸的影响,建立缝洞型管道模型,采用数值模拟与理论分析结合方法研究采空区内缝洞型管道内瓦斯爆炸的传播规律及管道长径比对瓦斯爆炸过程中速度与冲击波的影响。研究结果表明:在缝洞型结构内,随着火焰沿管道向前传播,各监测点速度逐渐变大、压力先增加后降低,而压力上升速率则表现出不规则的变化;缝洞结构加剧了火焰燃烧的剧烈程度,提高了管道内各监测点的温度峰值;在缝洞型管道内随长径比r增加,各监测点最大压力峰值以及速度大小依次降低。     

基于多孔环形喷嘴的可燃爆粉尘分散特征的密度效应研究*

为了研究不同密度的可燃爆粉尘在内置多孔环形喷嘴的20 L爆炸特性测试装置中的分散特征,基于负载粒子流方法、耦合DPM动量平衡方程和时间平均 Navier Stokes控制方程组,实现3种不同密度的煤粉、铝粉和锆粉在20 L爆炸测试装置中粉尘分散全过程的数值模拟。研究结果表明:多孔环形喷嘴的分散较为均匀,但是约束管道末端存在局部粉尘残留区,致使爆炸仓内真实粉尘浓度远低于形式浓度;爆炸仓中心位置的最大湍动能随着粉尘密度的增加而减小,只有显著地变化粉尘密度才能展示区分度较高的浓度峰值和抵达浓度峰值的时间。     

抛光铝粉爆炸及ABC粉体抑爆特性的实验研究

为研究抛光铝粉的爆炸危险和ABC粉体的抑爆特性,在对实验粉体粒径分布进行分析的基础上,采用20 L粉尘爆炸特性实验装置,分别对不同铝粉尘浓度、不同抑爆剂浓度条件下的爆炸特性参数进行测试。研究结果表明:在实验条件下,铝粉的爆炸下限为45 g/m3＜C＜60 g/m3;随铝粉浓度增加,爆炸烈度呈现出先增强后减弱的变化趋势,在浓度为400 g/m3时爆炸烈度最大。ABC抑爆剂能够有效抑制铝粉爆炸超压和爆炸反应进程,随着惰性粉体浓度的增加,抑制效果愈加明显,爆炸逐渐减弱。当ABC惰性粉体的质量占比增加到50%时,相较单一铝粉爆炸,反应过程时间由72 ms增加至785 ms,爆炸最大压力、最大压力上升速率分别下降了61.7%,89.5%;当ABC粉体质量占比为53%时,铝粉被完全惰化,未发生爆炸。     

Inherent thermal runaway hazard evaluation method of chemical process based on fire and explosion index

Thermal runaway hazard assessment provides the basis for comparing the hazard levels of different chemical processes. To make an overall evaluation, hazard of materials and reactions should be considered. However, most existing methods didn't take the both into account simultaneously, which may lead the assessment to a deviation from the actual hazard. Therefore, an integrated approach called Inherent Thermal-runaway Hazard Index (ITHI) was developed in this paper. Similar to Dow Fire and Explosion Index(F&EI) function, thermal runaway hazard of chemical process in ITHI was the product of material factor (MF) and risk index (RI) of reaction. MF was an indicator of material thermal hazards, which can be determined by initial reaction temperature and maximum power density. RI, which was the product of probability and severity, indicated the risk of thermal runaway during the reaction stage. Time to maximum rate under adiabatic conditions and criticality classes of scenario were used to indicate the runaway probability of the chemical process. Adiabatic temperature rise and heat of the desired reaction and secondary reaction were used to determine the severity of runaway reaction. Finally, predefined hazard classification criteria was used to classify and interpret the results obtained by this method. Moreover, the method was validated by case studies.     

Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

Study on explosion risk of aluminum powder under different dispersions

This paper mainly studied the influence of particle size distribution on the explosion risk of aluminum powder under the span of large particle size distribution. The measurement was carried out with the 20 L explosion ball and the Hartmann tube. The statistical analysis was used to analyze the relevance between the parameters of explosion risk and the particle size parameters. Test results showed that with the increase of particle size, the sensitivity parameter increases and the intensity parameter deceleration decreases. The effect of particle size change on MEC and MIE of small particle size aluminum powder is relatively small but greater impact on Pm and (dP/dt)m. The small particle size components greatly increasing the sensitivity of the explosion and accelerating the rate of the explosion reaction; while the large particle size component contributes to the maximum explosion pressure. D_3,2 particle size dust determines the risk of aluminum powder explosion.     

Risk assessment and risk reduction of an acrylonitrile production plant

Reducing accident occurrence in petrochemical plants is crucial, thus appropriately allocating management resources to safety investment is a vital issue for corporate management as international competition intensifies. Understanding the priority of safety investment in a rational way helps achieve this objective.In this study, we targeted an acrylonitrile plant. First, Dow Chemical's Fire and Explosion Index (F&EI) identified the reaction process as having the greatest physical risk. We evaluated the severity of accidents in the reaction process using the Process Safety Metrics advocated by the Center for Chemical Process Safety (CCPS); however, this index does not express damages a company actually experience. To solve this problem, we proposed a new metric that adds indirect cost to CCPS metrics. We adopted fault tree analysis (FTA) as a risk assessment method. In identifying top events and basic events, we attempted to improve the completeness of risk identification by considering accidents from the past, actual plant operation and equipment characteristics, natural disasters, and cyber-attacks and terrorist attacks. Consequently, we identified the top events with high priority in handling because of serious accidents as fire/explosion outside the reactor, fire/explosion inside the reactor, and reactor destruction. The new CCPS evaluation index proposed in this study found that fire and explosion outside the reactor has the highest severity. We considered the creation of the fault tree (FT) diagram of the top event, estimating the occurrence probability, and identifying the risk reduction part and capital investment aimed at risk reduction. As an economically feasible selection method for risk reduction investment, using the difference in loss amounts before and after safety investments indicated investment priority.     

Research on different venting performance between flat and curved bursting panels

There is a noticeable discrepancy in the ability to control reduced explosion overpressure between flat bursting panels and curved bursting panels with the same static activation overpressure. Flat bursting plates were observed to leak at approximately 80% of the static activation overpressure lower than curved bursting plates. A new experimental technique is proposed in our paper. Three different vent areas of flat and curved bursting panels were tested, there was significant difference in structural stiffness between flat bursting panels and curved bursting panels, which is the reason the discrepancy in the ability to control reduced explosion overpressure. The structural stiffness of the flat bursting panels is poorer than that of the other, and a greater deformation of the flat bursting panels occurs under the same load. The membrane stress caused by the explosion overpressure therefore produces a larger value in the flat bursting panels which causes it to open prematurely. Moreover, the smaller the vent area that is, the more significant discrepancy in controlling the reduced explosion overpressure between both bursting panels is. This experimental and theoretical result in our paper provides some useful experience for the method of explosion venting.