Effect of pipes in heat pump system on electric vehicle energy saving

ABSTRACT

Refrigerant pressure drop and temperature change in pipes are normally ignored in the thermodynamic analysis of traditional vehicle air conditioning system, this will result in serious errors. In this Paper, pressure drop and temperature difference are simulated in different pipes of electric vehicle (EV) heat pump system to analysis the effects of pipes in the actual EV heat pump system. The results indicate that the greater the mass flow, the faster pressure drop increases, the temperature difference decreases. Pressure drop of saturated liquid refrigerant is smaller than that of saturated gas refrigerant at the same saturation pressure and mass flow rate. The higher the refrigerant pressure (no phase change), the slower pressure drop decreases, the faster the temperature difference decreases. Pressure drop decreases with the increment of bending angle of the pipe. For EV heat pump system, suitable valves and less branches are helpful for energy saving of the system. Shortening the pipe between compressor and condenser can reduce temperature change obviously. Pressure drop per unit length in the pipe between evaporator and compressor is large especially in heating mode because of lower refrigerant density. It even reaches to over 100 times of that in the pipe between condenser and throttle valve in heating mode and has negative effects on the performance of the system. If the evaporator is closer to the compressor and the number of branches is less, then pressure drop will decrease a lot, which will be advantageous for energy saving of the heat pump system.     

Characteristics of stable biodiesel emulsion fuel with the aid of lipophilic surfactant,polyglycerol polyricinoleate (PGPR)

ABSTRACT

Biodiesel emulsion fuel is reported as one of the most feasible options capable of generating lower NOx emission than that from fossil fuels. However, oil and water in the emulsion fuel are easily separated and unstable. The aim of the present study is to consider the production and stability of biodiesel emulsion fuel by using tetraglycerin ester (CR-310), i.e., one of lipophilic surfactant, polyglycerol polyricinoleate (PGPR) and biodiesel, i.e., Waste cooking Oil Methyl Ester (WOME) produced based on waste cooking oil. The corresponding heat rate, water content, and viscosity are measured. Emphasis is placed on the effects of water content and surfactant on biodiesel emulsions. It is found that: (i) stable emulsion fuel is obtained by adding at least 2.0% of CR-310 and is maintained over 1 month, (ii) there is no effect of water content on stable emulsion fuel if CR-310 is used over 2.0%, and (iii) the viscosity of emulsion fuels is higher than that of the biodiesel fuel and is gradually increased with an increase in the water content.     

Fine-resolution mapping of wildfire fuel types for Canada: Fuzzy logic modeling for an Alberta pilot area

The Canadian Forest Fire Danger Rating System (CFFDRS) is used daily across Canada for evaluating forest fire danger. Fuel-type information is one of the inputs required by the models used in the CFFDRS. In this project, three fuel-type maps with a 25 m resolution were produced for a pilot study area located in Alberta using land cover only; land cover and biomass; and, land cover, biomass and leaf area index data derived from satellite imagery. The relationships between inputs and fuel types were determined mainly by the opinions of forest fire scientists and incorporated into a computer program using fuzzy set methodology. Not all the CFFDRS fuel types could be distinguished using these inputs; three of the coniferous types had to be grouped into one common fuel type. Overall accuracy was between 74 and 83% based on ground-truth comparisons. The most accurate map resulted from land cover and biomass data. Detailed accuracy assessment indicated that the overall accuracy increased up to 86% if ambiguous fuel type identification was considered. No combination of inputs was able to define a fuel type with absolute certainty, which is a reflection of differing expert opinions and the small number of inputs used to produce the maps.     

混合动力汽车尾气余热回收系统的研究

针对尾气余热能量浪费问题,建立了某直列四缸汽油机尾气余热回收发电的系统模型。通过B.T米特罗欣的数学分析法和涡轮特征曲线快速匹配到适合的涡轮机,然后根据涡轮特征曲线对高速发电机进行了匹配。以满足国Ⅴ标准的NEDC工况为参考,对整个系统进行了仿真分析。结果表明,该系统能够实现尾气余热能量的回收,在市区和市郊平均分别可以回收能量1 k W和1.5 k W,市郊最高可达1.8 k W。     

Unintentional non-traffic injury and fatal events: Threats to children in and around vehicles

Objective: There have been substantial reductions in motor vehicle crash–related child fatalities due to advances in legislation, public safety campaigns, and engineering. Less is known about non-traffic injuries and fatalities to children in and around motor vehicles. The objective of this study was to describe the frequency of various non-traffic incidents, injuries, and fatalities to children using a unique surveillance system and database.

Methods: Instances of non-traffic injuries and fatalities in the United States to children 0–14 years were tracked from January 1990 to December 2014 using a compilation of sources including media reports, individual accounts from families of affected children, medical examiner reports, police reports, child death review teams, coroner reports, medical professionals, legal professionals, and other various modes of publication.

Results: Over the 25-year period, there were at least 11,759 events resulting in 3,396 deaths. The median age of the affected child was 3.7 years. The incident types included 3,115 children unattended in hot vehicles resulting in 729 deaths, 2,251 backovers resulting in 1,232 deaths, 1,439 frontovers resulting in 692 deaths, 777 vehicles knocked into motion resulting in 227 deaths, 415 underage drivers resulting in 203 deaths, 172 power window incidents resulting in 61 deaths, 134 falls resulting in 54 deaths, 79 fires resulting in 41 deaths, and 3,377 other incidents resulting in 157 deaths.

Conclusions: Non-traffic injuries and fatalities present an important threat to the safety and lives of very young children. Future efforts should consider complementary surveillance mechanisms to systematically and comprehensively capture all non-traffic incidents. Continued education, engineering modifications, advocacy, and legislation can help continue to prevent these incidents and must be incorporated in overall child vehicle safety initiatives.     

Safe speed limits for a safe system: The relationship between speed limit and fatal crash rate for different crash types

Objective: The objective of this article is to provide empirical evidence for safe speed limits that will meet the objectives of the Safe System by examining the relationship between speed limit and injury severity for different crash types, using police-reported crash data.

Method: Police-reported crashes from 2 Australian jurisdictions were used to calculate a fatal crash rate by speed limit and crash type. Example safe speed limits were defined using threshold risk levels.

Results: A positive exponential relationship between speed limit and fatality rate was found. For an example fatality rate threshold of 1 in 100 crashes it was found that safe speed limits are 40 km/h for pedestrian crashes; 50 km/h for head-on crashes; 60 km/h for hit fixed object crashes; 80 km/h for right angle, right turn, and left road/rollover crashes; and 110 km/h or more for rear-end crashes.

Conclusions: The positive exponential relationship between speed limit and fatal crash rate is consistent with prior research into speed and crash risk. The results indicate that speed zones of 100 km/h or more only meet the objectives of the Safe System, with regard to fatal crashes, where all crash types except rear-end crashes are exceedingly rare, such as on a high standard restricted access highway with a safe roadside design.     

Motorcycle crashes potentially preventable by three crash avoidance technologies on passenger vehicles

Objective: The objective of this study was to identify and quantify the motorcycle crash population that would be potential beneficiaries of 3 crash avoidance technologies recently available on passenger vehicles.

Methods: Two-vehicle crashes between a motorcycle and a passenger vehicle that occurred in the United States during 2011–2015 were classified by type, with consideration of the functionality of 3 classes of passenger vehicle crash avoidance technologies: frontal crash prevention, lane maintenance, and blind spot detection. Results were expressed as the percentage of crashes potentially preventable by each type of technology, based on all known types of 2-vehicle crashes and based on all crashes involving motorcycles.

Results: Frontal crash prevention had the largest potential to prevent 2-vehicle motorcycle crashes with passenger vehicles. The 3 technologies in sum had the potential to prevent 10% of fatal 2-vehicle crashes and 23% of police-reported crashes. However, because 2-vehicle crashes with a passenger vehicle represent fewer than half of all motorcycle crashes, these technologies represent a potential to avoid 4% of all fatal motorcycle crashes and 10% of all police-reported motorcycle crashes.

Discussion: Refining the ability of passenger vehicle crash avoidance systems to detect motorcycles represents an opportunity to improve motorcycle safety. Expanding the capabilities of these technologies represents an even greater opportunity. However, even fully realizing these opportunities can affect only a minority of motorcycle crashes and does not change the need for other motorcycle safety countermeasures such as helmets, universal helmet laws, and antilock braking systems.     

Radium geochemistry in Na-Cl type groundwater in Niigata Prefecture, Japan

Radium isotopes in 23 Na-Cl type groundwater sampled mainly from deep wells in Niigata Prefecture, which is the site of the largest oil- and gas-fields in Japan, were measured along with U isotopes, chemical components and hydrogen and oxygen isotope ratios to elucidate the distribution and behavior of Ra in a brackish environment underground. Also analyzed were U and Th isotopes in 38 rock samples collected from outcrops at 17 locations. Ra-226 concentrations (8.86-1637 mBq kg⁻¹) of groundwater samples roughly correlated with total dissolved solid (TDS) concentrations and other alkaline earth contents. Their ²²⁸Ra/²²⁶Ra activity ratios (0.32-5.2) were similar to or higher than the ²³²Th/²³⁸U activity ratios (0.6-1.7) in the rocks. The most likely transport mechanism of Ra isotopes into groundwater was due to their α-recoil from the solid phase, probably from the water-rock interface where Th isotopes had accumulated, and adsorption/desorption reaction based on the increase in ²²⁶Ra contents with TDS.     

农村分散型的生活污水处理工程实例

介绍了农村小城镇分散型的生活污水处理经验,即采用隔油沉淀、水解酸化、接触氧化法的处理工艺;污水处理设施采用埋地式土壤覆盖型;最终废水出水的各项水质指标均达到《城镇污水处理厂污染物排放标准》（GB18918—2002）中的一级B类标准。     

污水处理厂一级A出水低温热能的回收与应用

阐述了国内外污水热能的应用现状,介绍了污水源热泵的工作原理、系统优越性、存在的问题。以工程实例证明污水源热泵是高效节能、经济可行、节能环保的新能源,对开发新的清洁能源、减少温室气体排放有重要价值。