应用区间层次分析法(IAHP)研究高层建筑火灾安全因素

高层建筑物的火灾安全影响因素繁多,其对建筑物火灾安全性的影响不容易确定,采用传统的层次分析法对某些因子的影响权重进行确定时难度较大.本文采用区间层次分析法来解决这一问题.首先建立影响高层建筑火灾安全的层次分析模型,然后用区间层次分析法确定影响因子,采用区间数特征根法求出各个火灾安全因子的权重值,并进行一致性检验.研究表明,影响高层建筑火灾安全的因子从大到小依次为:安全疏散措施、管理与维护、消防设施、报警与灭火系统、阻燃与防火结构,得到了每个因子的权重.采用同样的方法确定了每个影响因子的子因子的权重及重要性排序.其结果与实际情况基本相符.表明在进行高层建筑火灾安全性评估时,区间层次分析法是一种较好的方法.     

中国建筑火灾引起坍塌事故的统计与分析

为了研究火灾引起的建筑结构坍塌的机理,便于已有建筑的抗火防护和新建建筑的抗火设计,通过查询文献资料和新闻媒体报道,对我国建筑火灾坍塌事例进行了调查,对火灾坍塌建筑物的结构形式、层数和使用功能等方面进行了统计分析,列出了部分我国火灾史上1960-2005年所发生的火灾坍塌事例.调查结果显示,钢结构、特别是工业厂房钢屋架在火灾下较其他形式的建筑易发生坍塌;4～8层的民用建筑发生火灾坍塌的比例较高;工业厂房,仓库和商业建筑发生火灾坍塌的比例较高;民用建筑多发生局部坍塌;发生坍塌的建筑一般存在设计和施工不规范以及防火设施不合格等情况.     

PCDD/Fs in ambient air collected in Zagreb, Croatia

Levels of PCDD/Fs were measured at four different sites in Zagreb, capital of Croatia. Also one sample was taken during spontaneously initiated open fire on a landfill and one sample where garden waste of unknown content was burnt. Over period 1997–2000, 28 samples were collected and levels ranged between 9 and 306 fg I-TEQ m⁻³, except in the sample collected during landfill fire. Air PCDD/F levels in Zagreb at four sites were different and the highest levels were observed in industrial area. Seasonal variation of levels is also evident with higher levels in winter than in summer. Our results show that PCDD/F levels in ambient air collected in Zagreb are at lower end of the published data range. In general, homologue profiles were quite similar for all locations, the concentration of PCDD homologues increased while the concentration of PCDF homologues decreased with increasing degree of chlorination. PCDD/F levels in the landfill fire sample was 13 200 fg I-TEQ m⁻³ which are much higher than levels in garden waste burning sample or in sample collected at industrial site. During landfill fire, the concentration of 2,3,7,8-TCDF becomes even higher than the concentration of OCDF and is equal to the concentration of 1,2,3,4,6,7,8-HpCDF.     

Comparison of trace element concentrations in livers of diseased, emaciated and non-diseased southern sea otters from the California coast

Infectious diseases have been implicated as a cause of high rates of adult mortality in southern sea otters. Exposure to environmental contaminants can compromise the immuno-competence of animals, predisposing them to infectious diseases. In addition to organic pollutants, certain trace elements can modulate the immune system in marine mammals. Nevertheless, reports of occurrence of trace elements, including toxic heavy metals, in sea otters are not available. In this study, concentrations of 20 trace elements (V, Cr, Mn, Co, Cu, Zn, Rb, Sr, Mo, Ag, Cd, In, Sn, Sb, Cs, Ba, Hg, Tl, Pb, and Bi) were measured in livers of southern sea otters found dead along the central California coast (n = 80) from 1992 to 2002. Hepatic concentrations of trace elements were compared among sea otters that died from infectious diseases (n = 27), those that died from non-infectious causes (n = 26), and otters that died in emaciated condition with no evidence of another cause of death (n = 27). Concentrations of essential elements in sea otters varied within an order of magnitude, whereas concentrations of non-essential elements varied by two to five orders of magnitude. Hepatic concentrations of Cu and Cd were 10- to 100-fold higher in the sea otters in this study than concentrations reported for any other marine mammal species. Concentrations of Mn, Co, Zn, and Cd were elevated in the diseased and emaciated sea otters relative to the non-diseased sea otters. Elevated concentrations of essential elements such as Mn, Zn, and Co in the diseased/emaciated sea otters suggest that induction of synthesis of metallothionein and superoxide dismutase (SOD) enzyme is occurring in these animals, as a means of protecting the cells from oxidative stress-related injuries. Trace element profiles in diseased and emaciated sea otters suggest that oxidative stress mediates the perturbation of essential-element concentrations. Elevated concentrations of toxic metals such as Cd, in addition to several other organic pollutants, may contribute to oxidative stress-meditated effects in sea otters.     

Mitigation of CO2 Emissions from the EU-15 Building Stock. Beyond the EU Directive on the Energy Performance of Buildings (9 pp)

-

Goal Scope and Background. The European Directive on Energy Performance of Buildings which came into force 16 December 2002 will be implemented in the legislation of Member States by 4 January 2006. In addition to the aim of improving the overall energy efficiency of new buildings, large existing buildings will become a target for improvement, as soon as they undergo significant renovation. The building sector is responsible for about 40% of Europe's total end energy consumption and hence this Directive is an important step for the European Union in order that it should reach the level of saving required by the Kyoto Agreement. In this the EU is committed to reduce CO2 emissions relative to the base year of 1990 by 8 per cent, by 2010. But what will be the impact of the new Directive, how large could be the impacts of extending the obligation for energy efficiency retrofitting towards smaller buildings? Can improvement of the insulation offset or reduce the growing energy consumption from the increasing installation of cooling installations? EURIMA, the European Insulation Manufacturers Association and EuroACE, the European Alliance of Companies for Energy Efficiency in Buildings, asked Ecofys to address these questions.

Methods

The effect of the EPB Directive on the emissions associated with the heating energy consumption of the total EU 15 building stock has been examined in a model calculation, using the Built Environment Analysis Model (BEAM), which was developed by Ecofys to investigate energy saving measures in the building stock. The great complexity of the EU-15 building stock had to be simplified by examining five standard buildings with eight insulation standards, which are assigned to building age and renovation status. Furthermore, three climatic regions (cold, moderate, warm) were distinguished for the calculation of the heating energy demand. This gave a basic 210 building types for which the heating energy demand and CO2 emissions from heating were calculated according to the principles of the European Norm EN 832.

Results and Discussion

The model calculations demonstrates that the main contributor to the total heating related CO2 emissions of 725 Mt/a from the EU building stock in 2002 is the residential sector (77%) while the remaining 23% originates from non-residential buildings. In the residential sector, single-family houses represent the largest group responsible for 60% of the total CO2 emissions equivalent to 435 Mt/a.

-

- The technical potential: If all retrofit measures in the scope of the Directive were realised immediately for the complete residential and non-residential building stock the overall CO2 emission savings would add up to 82 Mt/a. An additional saving potential compared to the Directive of 69 Mt/a would be created if the scope of the Directive was extended to cover retrofit measures in multi-family dwellings (200-1000m2) and non-residential buildings smaller than 1000m2 used floor space. In addition including the large group of single-family dwellings would lead to a potential for additional CO2 emission reductions compared to the Directive of 316 Mt/a.

-

- Temporal mobilization of the potential: Calculations based on the building stock as it develops over time with average retrofit rates demonstrated that regulations introduced following the EPB Directive result in a CO2 emissions decrease of 34 Mt/a by the year 2010 compared to the business as usual scenario. Extending the scope of the EPB Directive to all residential buildings (including single and multi-family dwellings), the CO2 emission savings potential over the 'business as usual' scenario could be doubled to 69 Mt/a in the year 2010. This creates an additional saving potential compared to the Directive of 36 Mt/a.

-

- Cooling demand: The analysis demonstrated that in warm climatic zones the cooling demand can be reduced drastically by a combination of lowering the internal heat loads and by improved insulation. With the reduction of the heat loads to a moderate level the cooling demand, e.g. of a terraced house located in Madrid, can be reduced by an additional 85% if the insulation level is improved appropriately.

Conclusions

This study demonstrates that the European Directive on Energy Performance of Buildings will have a significant impact on the CO2 emissions of the European building stock. The main saving potential lies in insulation of the existing building stock. Beyond this, CO2 emissions could, however, be greatly reduced if the scope of the Directive were to be extended to include retrofit of smaller buildings.

Recommendation and Perspective

The reductions should be seen in relation to the remaining gap of 190 Mt CO2 eq. per annum between the current emission levels of EU-15 and the target under the Kyoto-Protocol for the year 2010. The energy and industrial sector will probably contribute only a fraction of this reduction via the newly established EU emissions trading scheme and connected projects under the flexible mechanism. In addition, the traffic sector is likely to continue its growth path leading to a widening of the gap. Thus, there is likely to be considerable pressure on the EU building sector to contribute to the EU climate targets beyond what will be achieved by means of the current EPB Directive. Legislators on the EU and national level are therefore advised to take accelerated actions to tap the very significant emission reduction potentials available in the EU building stock.     

Biodegradability,hydrolytic degradability,and builder performance in detergent formulations of partially dicarboxylated alginic acid

Partially dicarboxylated alginic acids with degree of dicarboxylations from 13 to 61 mol% were prepared and their biodegradability, hydrolytic degradability, and builder performances in detergent formulations were measured. Also, the correlations between biodegradability and hydrolytic degradability were examined with respect to the degree of dicarboxylation. The biodegradability of dicarboxylated alginic acid sodium salt (DCAa), evaluated by biochemical oxygen demand with activated sludge, depended on the degree of dicarboxylation. DCAa containing more than 75 mol% remaining uronide residues in the polymer chain showed excellent biodegradation. Hydrolytic degradation of DCAa depended on the degree of dicarboxylation and the pH of the incubation media. After 30-day incubation at 30°C at pH 4–6, a significant molecular weight reduction by hydrolytic degradation was observed for highly dicarboxylated alginic acid. DCAa with a high degree of dicarboxylation showed excellent builder performance in detergent formulations based on the detergency and calcium sequestration capacity.     

New environmental performance baseline for inland ports: A benchmark for the European inland port sector

This paper presents the results of a collaborative programme of action between the European Federation of Inland Ports (EFIP) and the EC PORTOPIA research project to assist EU inland ports to enhance further their environmental performance. In order to achieve this goal, an environmental survey was specifically designed to reflect the operational and geographical circumstances of inland ports and to help to accelerate the culture of the reporting of environmental performance.The survey was developed to be user-friendly and practicable, and based on established good-practice taking into account the suggestions and advice of EFIP and its members, as well as the experience of the EcoPorts Network. As a result of the survey, an initial baseline of environmental performance for the EU inland port sector was established.A total of 27 port authorities participated in the survey, representing a range of port profiles in terms of size, commercial profile and geography. All response details were treated in strict confidence and the benchmark performance was reported as a European average. Results show that approximately 70% of the respondent ports declare that they have the major components of an Environmental Management System (EMS) actively in place (e.g. policy, inventory of legislation). An environmental index (1–10) has been calculated reflecting the performance of the sector in terms of the application of major EMS components. The average index value for the EU inland port sector baseline resulted in 6.Almost 67% of respondent ports indicated that they conduct environmental monitoring of different aspects, with waste being the most common. The survey results have also delivered the first top-10 ranking of environmental priorities for the EU inland port sector. It is interesting to note that also almost 70% of the inland ports apply initiatives to implement green actions. The outcomes of this paper are likely to be of interest to a wide range of stakeholders and decision-makers.     

电弧防护服性能测试及影响因素研究

针对电力行业电弧引发的事故,电弧防护服相关标准开始制定并逐步完善。现有电弧防护性能的标准测试方法包括开弧测试和盒式测试,针对不同形式的电弧,测试方式仍在不断发展。电弧防护性能的最常用的衡量指标是电弧热性能值ATPV。对于不同工作场所电弧服的选择是基于对工作现场的危害评级。最后文章总结了电弧防护服性能影响因素的研究,包括电弧防护性、热湿舒适性和作业适应性。未来的电弧防护服的开发会朝向更安全、低成本、更舒适的方向进行。     

Indoor air quality and academic performance

I examine the effect of school indoor air quality (IAQ) on academic outcomes. I utilize a quasi-natural experiment, in which IAQ-renovations were completed at virtually every school in a single Texas school district at different points in time, combined with a panel of student-level data to control for many confounding factors and thereby uncover the causal effect of IAQ-renovations on academic outcomes. Results indicate that performance on standardized tests significantly improves while attendance is unresponsive to improvements in IAQ. Rough calculations suggest that IAQ-renovations may be a more cost-effective way to improve standardized test scores than class size reductions.     

钢筋混凝土梁在火侵袭下的反应分析

结构物在大火侵袭下，结构内部温度和结构挠度、内力将随时间发生不断变化，这种变化极为复杂。本文在试验研究的基础上，采用非线性有限元法，着重研究钢筋混凝土梁在火侵袭作用下其温度和挠度的反应，提出了一种理论分析方法，编制了计算机程序，对钢筋混凝土梁的温度、挠度和内力的反应进行了计算，并得到试验结果的验证。