缙云山3种典型森林降雨过程及其氮素输入

选取重庆缙云山的常绿阔叶林、毛竹林和针阔混交林为研究对象,于2012年5~10月对大气降水、穿透雨和树干径流等降水过程及其氮素输入进行研究.结果表明:①研究期间总降雨量564.88 mm,常绿阔叶林、毛竹林和针阔混交林的穿透雨量占总降雨量的比例分别为74.0%、85.0%和71.6%,且树干径流量所占比例分别为1.9%、10.3%和1.6%;3种林分的穿透雨量、树干径流量与林外降雨量之间均呈显著的线性关系(P<0.05),且穿透雨率、树干径流率与林外降雨量之间都呈对数关系(P<0.05).②与大气降水相比,穿透雨和树干径流的NO-3和NH+4浓度要高,且3种林分的大小关系为针阔混交林>常绿阔叶林>毛竹林;穿透雨和树干径流的总无机氮输入量(以N计)分别为针阔混交林(18.93 kg·hm-2)、常绿阔叶林(14.93 kg·hm-2)和毛竹林(15.31 kg·hm-2).③3种林分的无机氮输入量与穿透雨量、树干径流量之间均呈显著的线性关系(P<0.05).     

SFBR中好氧颗粒污泥的培养及特性研究

接种自行培养的活性污泥,以模拟废水为基质,采用连续进水、间歇出水及厌氧/好氧交替的运行模式,尝试了在SFBR中进行好氧颗粒污泥的培养,并研究了好氧颗粒污泥的特性及反应器对污染物的去除效果.结果表明,通过逐步缩短沉降时间,28 d时成功培养出好氧颗粒污泥,所形成的好氧颗粒污泥呈黄色、形状不规则,且粒径较小(平均粒径0.56 mm),正常情况下的SVI保持在70 mL·g-1以下,EPS在59 d时达到最大值(以MLVSS计)373.24 mg·g-1,较培养初期增加了约2.5倍,运行后期由于颗粒出现解体,导致EPS急剧下降;反应器在运行过程中未能保持较高的污泥量,中后期MLSS始终在3 000mg·L-1以下;在63 d的运行时间里,除异常波动外,反应器对COD的去除率基本维持在90%左右,正常情况下出水COD小于100 mg·L-1,反应器对NH+4-N、TIN的去除效果波动较大,去除率分别为44.45%~94.72%及43.87%~93.13%,反应器对TP的去除率在44.50%~97.40%之间,正常情况下TP去除率可维持在60%以上;限于自动控制水平,夜间长时间的好氧饥饿期容易造成丝状菌过度生长,使得AGS在生长竞争中处于劣势,最终导致了AGS的解体.     

连续流反应器短程硝化的快速启动与维持机制

如何快速稳定地启动短程硝化工艺对低C/N比废水的处理具有十分重要的实际应用价值.针对城市污水厂以连续流工艺为主的现状,故对连续流反应器短程硝化的快速启动与维持进行研究.结果表明,利用间歇曝气,依次控制3个阶段的停/曝时间(15 min/45 min、45 min/45 min和30 min/30 min),连续流反应器经过60 d左右的运行,可以成功实现短程硝化的快速启动.控制停/曝时间为30 min/30 min,进水氨氮浓度为50或100 mg·L~(-1)时,亚硝化率分别可达90%或95%.另外,间歇曝气有利于抑制硝化菌(NOB)的活性,而缩短水力停留时间(HRT)可淘洗出NOB,两者结合可以更好地维持短程硝化.     

SCAR处理城市生活污水的效能及其微生物群落动态分析

利用强化循环厌氧反应器(SCAR)处理模拟城市生活污水,研究不同负荷条件下的反应器运行特征、污泥特性及微生物种群结构.结果表明,水力停留时间(HRT)为6 h可以作为反应器高效运行的关键控制参数,该条件下污水化学需氧量(COD)去除率达到75%以上.随着反应器容积负荷的逐渐提高,颗粒污泥中辅酶F420和产甲烷活性(SMA)逐渐增加,胞外聚合物(EPS)含量也不断提高,其中紧密黏附EPS(TB-EPS)含量的增加尤其明显.厌氧颗粒污泥性状和反应器对污染物的去除效率同时受到污泥负荷和HRT的影响,微生物的群落结构及其在反应器中的空间分布也受到污泥负荷的影响,不同代谢特征微生物在反应器不同空间位置的相对丰度随着污泥负荷的调整而改变.     

低温条件IASBR处理养猪沼液脱氮性能研究

以实际养猪沼液为研究对象,考察分步进水间歇曝气序批式生物反应器(IASBR)在低温条件下的脱氮性能.结果表明:IASBR反应器的硝化性能临界水温为10℃,水温低于10℃时硝化性能急剧下降,水温10℃以上时氨氮去除率达到90%以上,且水温15℃以上氨氮负荷极限可达到0.30 kg·m~(-3)·d~(-1);低碳氮比(COD/TN)1.7±0.3条件下,反硝化性能临界水温为20℃,20℃以上时TN去除率可保持在80%以上,最高达90%,20℃以下时脱氮效率明显降低,出现亚硝态氮积累现象.此外,IASBR反应器脱氮除磷效率高,温度对TOC和TP去除率的影响不敏感.不排泥条件下,进水COD/TN为3.1±0.4时,TN去除率高达90%以上,TOC和TP去除率分别高达83.6%±3.9%和58.5%±17.8%;随后COD/TN降低至1.7±0.3后,TN去除率仍高达80%以上,TOC和TP去除率仅略有降低分别为77.3%±4.6%、53.1%±10.1%.     

甲硫醇降解菌群筛选及其降解特性研究

从处理甲硫醚(DMS)和丙硫醇(PT)混合废气的生物滴滤塔中富集出一组能够有效降解甲硫醇(MT)的混合菌群,并对其特性进行了系列研究.结果表明,该混合菌群能有效降解MT,菌群较为适宜的生长和降解条件为30℃、p H=7.0,在该条件下能将初始浓度为20 mg·L~(-1)的MT在70 h内降解完全.添加酵母膏(YE)后,MT降解速率进一步提高,降解所需时间缩短10 h.利用高通量测序技术分析混合菌群的群落结构,发现其中优势菌属为Pseudomonas sp.、Thiobacillus sp.和Acinetobacter sp.,所占比例分别为33.78%、21.91%和17.01%.中间产物检测结果表明,混合菌群降解MT的过程中产生了甲醛、H_2S、二甲基二硫醚(DMDS)等物质,推断MT的降解途径可能有如下2条:(1)MT在MT氧化酶作用下形成甲醛和H2S,随后氧化为SO_4~(2-);(2)MT依次转化为DMDS、DMS、二甲基亚砜(DMSO)和二甲基砜(DMSO_2),最后经甲基磺酸(MSA)可生成SO_4~(2-).     

Selection of appropriate organic additives for enhancing Zn and Cd phytoextraction by hyperaccumulators

Chelant-enhanced phytoextraction is one of the most promising technologies to remove heavy metals from soil. The key of the technology is to choose suitable additives in combination with a suitable plant. In the present study, laboratory batch experiment of metal solubilization, cress seeds germination were undertaken to investigate the metal-mobilizing capability and the phytotoxicity of organic additives, including ethylene diamine triacetic acid （EDTA）, citric acid, acetic acid, oxalic acid, glutamine and monosodium glutamate waste liquid （MGWL） from food industry. Experiments in pots were carried out to study the effects of the additives on Zn and Cd phytoextraction. Furthermore, a leaching experiment with lysimeter was performed to evaluate the environmental risks of additive-induced leaching to underground water. The results showed that EDTA had a strong mobilizing ability for Zn and Cd, followed by mixed reagent （MR） and MGWL. MGWL and acetic acid at 5 mmol equivalent per liter resulted in seed germination index less than 2%. Experiments in pots verified the phytotoxicity of acetic acid and MGWL. Addition of the mixed reagent at 6--10 mmol/kg significantly increased Zn phytoextraction by Thlaspi caerulescens. The same for EDTA and the mixed reagent at 10 mmol/kg by Sedum dfredii. But only mixed reagents could significantly increase Cd phytoextraction by the studied hyperaccumulators. This suggested that the strong chelant was not always the good agent to enhance phytoextraction. S. alfredii combined with 2--10 mmol/kg soil MR was preferred for phytoremediation of Cd/Zn contaminated soils in southern China, this could result in high phytoextraction of Cd/Zn and reduce the leaching risk to underground water than EDTA assisted phytoextration.     

基于蒙特卡洛模拟的多米诺事故风险量化管理*

为降低危化品相关的化工事故造成的人员伤亡和财产损失,以化工多米诺事故为研究对象,探讨由初始事故引发1个或多个次生事故的连锁反应机理与风险评估方法。提出应用蒙特卡洛模拟对多米诺事故风险进行动态量化的方法,梳理化工多米诺事故风险的识别、分析、评定、处理全周期管理流程,并以1个天然气压气站为案例,验证基于蒙卡模拟的化工多米诺事故风险量化方法的有效性。结果表明:该方法可以更准确地对化工多米诺事故风险进行定量评估。多米诺事故风险全周期管理流程的梳理能够有效指导化工企业开展安全管理、事故预防等工作。     

Emergency shutdown of fluidized bed reaction systems

With several industrial applications of fluidized bed technology recently commercialized worldwide, it becomes essential to develop safe operation methods for fluidized bed reaction systems (FBRSs) to prevent any influence on their process values, which lead to accidents. To preventing any disaster or malfunction in an FBRS, an emergency shutdown system (ESD) is initiated, closing the reaction system in case of any abnormality by effectively isolating the flammable gas. However, an ESD is also prone to the “inactivation problem,” in which in the case of failure it initiates the emergency shutdown, even when the operating conditions of the reaction system are abnormal. It is also vulnerable to a “malfunction problem,” where the emergency shutdown is performed even when the operating conditions of the reaction system are normal. In this study, these problems were solved by investigating a reaction system through the monitoring of appropriate parameters and setting up of trigger levels, which reflect the uniqueness of an FBRS using an ESD. The parameters were identified by analyzing the scenario leading to an accident. The trigger levels were determined as the points at which the loss is smaller in the presence of an ESD, as compared to the value of the loss function in the presence or absence of an ESD. Furthermore, the ESD design model was applied as a case study in the ammoxidation process of propylene. The results showed that an ESD can prevent an approximately 8 billion yen of loss due to accidents in plant operations, against an investment of 200 million yen.     

Assessing Spatial, Temporal, and Analytical Variation of Groundwater Chemistry in a Large Nuclear Complex, USA

Statistical analyses were applied at the Hanford Site, USA, to assess groundwater contamination problems that included (1) determining local backgrounds to ascertain whether a facility is affecting the groundwater quality and (2) determining a ‘pre-Hanford' groundwater background to allow formulation of background-based cleanup standards. The primary purpose of this paper is to extend the random effects models for (1) assessing the spatial, temporal, and analytical variability of groundwater background measurements; (2) demonstrating that the usual variance estimate s ², which ignores the variance components, is a biased estimator; (3) providing formulas for calculating the amount of bias; and (4) recommending monitoring strategies to reduce the uncertainty in estimating the average background concentrations. A case study is provided. Results indicate that (1) without considering spatial and temporal variability, there is a high probability of false positives, resulting in unnecessary remediation and/or monitoring expenses; (2) the most effective way to reduce the uncertainty in estimating the average background, and enhance the power of the statistical tests in general, is to increase the number of background wells; and (3) background for a specific constituent should be considered as a statistical distribution, not as a single value or threshold. The methods and the related analysis of variance tables discussed in this paper can be used as diagnostic tools in documenting the extent of inherent spatial and/or temporal variation and to help select an appropriate statistical method for testing purposes.