水解酸化＋两级生物接触氧化处理高盐度水产品加工废水

介绍了“水解酸化＋两级生物接触氧化”处理水产品加工废水的运行效果和工程实例，结果表明：对C1^-浓度平均6000mg／L的高盐度水产品加工废水，系统对COD、SS、氨氮的去除率分别超过了88％、90％、85％，出水COD、SS、氨氮分别低于100mg／L、70mg／L、15mg／L，出水完全可以达到《污水综合排放标准》（GB8978—1996）一级排放标准。     

干法加氨脱除SO2中的温度效应

研究了在ＮＨ３参与下，干法脱除ＳＯ２中的温度效应，实验结果表明，在ＳＯ２与ＮＨ３的热化学反应中，反应程度随温度上升呈线性下降，然而，在脉冲电晕条件下，ＳＯ２脱率却随温度上升呈现非线性变化，通过测定不同温度下的产物组成，揭示了在脉８冲电晕放电条件，干法脱除ＳＯ２存在两条平反应途径；（１）先成盐后氧化；（２）先氧化后成盐，在较高温度下反应主要按第（２）条途径进行。     

湿法烟气脱硫应用中的几个问题探讨

对火电厂应用石灰石 石膏法烟气脱硫中遇到的几个实际问题进行分析和讨论 ,重点讨论分析了湿法烟气脱硫和烟气温度、烟气抬升高度、烟气扩散的关系 ,并分析了湿法烟气脱硫对烟囱产生的腐蚀影响     

重型柴油车污染物排放量计算方法比较分析

目的 计算大功率大吨位级重型柴油车的污染物排放量.方法 根据《公路隧道通风设计细则》和世界道路协会(PIARC)2012年技术报告,分别计算32 t重型柴油车的污染物排放量和稀释污染物所需的通风量,对比分析两种计算方法的差异.结果 对《公路隧道通风设计细则》中柴油车的车型系数和海拔高度系数提出建议.根据世界道路协会(PIARC)2012年技术报告,在0～2000 m低海拔地区,国产32 t柴油车的CO、NOx和烟尘排放量分别为88.6、166.0 m3/(h·veh)和84.2 m2/(h·veh),如果考虑NOx的空气污染,稀释单辆国产32 t柴油车排放污染物所需空气量约为33000 m3/h;如果不考虑NOx的空气污染,所需空气量约为28000 m3/h.结论 结合工程实际,建议大功率大吨位级重型柴油车的污染物排放量根据世界道路协会(PIARC)2012年技术报告进行计算.     

试用平炉尘制备中温变换催化剂

利用钢铁厂平炉尘制备中温变换催化剂,制备成本低,工艺简单,活性达到部颁标准,具有明显的经济效益.     

Effects of alternating temperatures on development and reproduction of the armyworm,Mythimna separata (Walker)

Effects of cycling and constant temperature on development and reproduction of the armyworm, Mythimna separata (Walker) were investigated by rearing the insects on the artificial diet under temperatures covering low(16-24℃ vs. 20 ℃ ), medial(20-28℃ vs. 24℃ ) and high(24-32 ℃ vs. 28 ℃) regions. In the low region, all the immature stages of the insect developed significantly faster under alternating temperatures than at corresponding constant temperatures. For the medial region, their development was little affected by variable temperatures. For the high region, developmental durations tended to be longer under cycling temperatures except egg stage.Mean fecundities of the adult moths markedly increased under cycling temperatures as compared with those at respective constant temperature in all regions.Possible reasons for effect of alternating temperatures on insect development are discussed in some details.     

活性硅酸聚合硫酸铁的研究

以硅酸钠，硫酸和聚合硫酸铁为原料制备活性硅酸合硫酸铁，测定了ＡＳＰＦＳ红外光谱，了Ｆｅ／Ｓｉ摩尔比和水样ＰＨ值等因素对产品和除浊效果的影响当Ｆｅ／Ｓｉ摩尔比为１．５时产品稳定性和除浊效果均较好。     

深度平均的应力-通量代数全场模型及其验证

提出了深度平均的应力—通量代数全场模型，用来模拟热水侧向排入大水体的各向异性的输移扩散规律。应用有限体积法对控制方程进行离散，利用ＳＩＭＰＬＥ法进行数值模拟。通过该模式的模拟计算给出了速度场、温度场的分布。所得的回流区形状及温度场分布与深度平均的ｋ－ε模型及实验资料对比，本文的计算结果与实测值符合得较好     

Comparison of mesophilic and thermophilic anaerobic digestions of thermal hydrolysis pretreated swine manure: Process performance, microbial communities and energy balance

Anaerobic digestion (AD) of swine manure (SM) commonly shows low biogas output and unsatisfactory economic performance. In this study, thermophilic AD (TAD, 50 ± 1 °C) was combined with thermal hydrolysis pretreatment (THP, 170 °C/10 bar), to investigate its potential for maximizing biogas yield, securing successful digestion and microbial diversity, as well as improving energy balance. Four lab-scale continuously stirred tank reactors were operated for 300 days and compared with each other, i.e., reactor 1 (raw SM fed in mesophilic AD: RSM-MAD), reactor 2 (THP-treated SM fed in MAD: TSM-MAD), reactor 3 (RSM-TAD), and reactor 4 (TSM-TAD). The results showed that THP was efficient to increase methane production of SM, TSM-TAD mode led to the highest methane yield (129.8 ± 40.5 mL-CH₄/g-VS/day) among the tests (p < 0.05). Although TAD was more likely to induce free ammonia (> 700 mg/L) or volatile fatty acids (> 6000 mg/L) accumulation compared with MAD in start-up phase, TSM-TAD treatment mode behaved a sustainable digestion process in a long-term operation. For TSM-TAD scenario, higher Shannon–Weaver (3.873) and lower Simpson index (0.061) indicated this mode ensured and enlarged the diversity of bacteria communities. Phylum Bathyarchaeota was dominant (59.3%−90.0%) in archaea community, followed by Euryarchaeota in the four reactors. RSM-MAD treatment mode achieved the highest energy output (4.65 GJ/day), TSM-TAD was less effective (−17.38 GJ/day) due to increased energy demands. Thus improving the energetic efficiency of THP units is recommended for the development of TSM-TAD treatment mode.     

高强铝合金超塑挤压成形

主要介绍了工业牌号高强铝合金在供应态或经简单预处理后在通用油压机上超塑成形的实例,并分析探讨了非理想组织材料超塑成形中微观组织的变化。