基于稳定氢同位素的太原市大气单环芳烃来源

采集太原市城北和城南区域环境空气和5类污染源挥发性有机物样品,测定样品中典型单环芳烃稳定氢同位素（δD）组成,基于同位素质量平衡原理计算单环芳烃从源到环境空气受体的δD初始混合值,探讨单环芳烃来源.结果表明,柴油挥发源、溶剂挥发源、汽油挥发源（97^#）、汽油挥发源（95^#）、机动车尾气（97^#）、机动车尾气（95^#）和民用燃煤源中单环芳烃δD范围依次为：（-138.7‰~-115.5‰）、（-147.0‰~-121.0‰）、（-150.8‰~-117.6‰）、（-131.8‰~-113.8‰）、（-171.2‰~-120.0‰）、（-138.9‰~-102.7‰）和（-168.3‰~-142.3‰）,民用燃煤源中单环芳烃δD显著贫重氢同位素（D）组成,机动车尾气源与汽油挥发源中苯的δD相比显著贫D,可用于探索污染物转化过程;城北和城南环境空气中δD范围为（-131.7‰~-115.1‰）和（-131.9‰~-74.9‰）,δD初始混合值为-138.4‰和-173.9‰,体现了其来源差异.     

科技创新投入对环境全要素生产率的影响机制

使用2004~2015年的中国280个地级市的面板数据,对科技创新投入与环境全要素生产率间的非线性关系、内部影响机理和空间异质性进行分析,结果显示：科技创新投入与环境全要素生产率之间呈现倒N型关系,两个拐点的位置分别为7.722（2257.47万元）和9.610（14913.17万元）;在外部资本进入、污染治理、市场规模效应3种影响路径中,科技创新投入影响下的外部资本进入对环境全要素生产率依然存在污染避难所的负向效应,科技创新投入与外部资本间效应为0.1363,外部资本与环境全要素生产率间效应为-0.0065;科技创新投入能够增强企业的污染治理技术并提高环境全要素生产率,三者间前后效应分别为-0.0277和-0.0311;科技创新的投入与高效益增强了市场规模效应,有效促进生产结构的转型进而提高环境全要素生产率,三者间前后效应为0.0186和0.4346.空间异质性中,外部资本进入与溢出效应带来的污染避难所负效应在中部地区显著,在西部和东北部地区不显著,而污染天堂正效应在东部地区存在但不显著;污染创新治理投入的技术正溢出效应在东部和西部地区效应显著,在中部和东北部不显著;科技创新投入与市场需求规模效应在空间区域无差异且显著为正.建议依据科技创新投入的不同影响路径来实施空间差异化策略.     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Photodegradation of Hexafluoropropylene Oxide Trimer Acid under UV Irradiation

As a novel alternative to traditional perfluoroalkyl substances (PFASs), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), hexafluoroproplyene oxide trimer acid (HFPO-TA) has been detected worldwide in surface water. Moreover, recent researches have demonstrated that HFPO-TA has stronger bioaccumulation potential and higher hepatotoxicity than PFOA. To treat these contaminants e.g. PFOA and PFOS, some photochemical techniques by adding exogenous substances had been reported. However, there is still no report for the behavior of HFPO-TA itself under direct UV irradiation. The current study investigated the photo-transformation of HFPO-TA under UV irradiation in aqueous solution. After 72 hr photoreaction, 75% degradation ratio and 25% defluorination ratio were achieved under ambient condition. Reducing active species, i.e., hydrated electrons and active hydrogen atoms, generated from water splitting played dominant roles in degradation of HFPO-TA, which was confirmed by different effects of reaction atmospheres and quenching experiments. A possible degradation pathway was proposed based on the products identification and theoretical calculations. In general, HFPO-TA would be transformed into shorter-chain PFASs, including hexafluoropropylene oxide dimer acid (HFPO-DA), perfluoropropionic acid (PFA) and trifluoroacetate (TFA). This research provides basic information for HFPO-TA photodegradation process and is essential to develop novel remediation techniques for HFPO-TA and other alternatives with similar structures.     

Sources, distribution, and risk assessment of organochlorine pesticides in Nairobi City, Kenya

The distribution and sources of organochlorine pesticides (OCPs) in air and surface waters were monitored in Nairobi City using triolein-filled semipermeable membrane devices (SPMDs). The SPMDs were extracted by dialysis using n-hexane, followed by cleanup by adsorption chromatography on silica gel cartridges. Sample analysis was done by GC-ECD and confirmed by GC–MS. Separation of means was achieved by analysis of variance, followed by pair-wise comparison using the t-test (p≤ 0.05). The total OCPs ranged between 0.018 – 1.277 ng/m³ in the air and <LOD – 1391.000 ng/m³ in surface waters. Based on the results, the means of Industrial Area, Dandora and Kibera were not significantly different (p≤ 0.05), but were higher (p≤ 0.05) than those of City square and Ngong’ Forest. The results revealed non-significant (p≤ 0.05) contribution of long-range transport to OCP pollution in Nairobi City. This indicated possible presence of point sources of environmental OCPs in the city. The water-air fugacity ratios indicated that volatilization and deposition played an important role in the spatial distribution of OCPs in Nairobi City. This indicated that contaminated surface waters could be major sources of human exposure to OCPs, through volatilization. The incremental lifetime cancer risks (ILCR) determined from inhalation of atmospheric OCPs were 2.3745  ×  10^?13 – 1.6845  ×  10^?11 (adult) and 5.5404  ×  10^?13 – 3.9306  ×  10^?11 (child) in the order: Dandora > Kibera > Industrial Area > City Square > Ngong’ Forest. However, these were lower than the USEPA acceptable risks, 10^?6 – 10^?4. This study concluded that atmospheric OCPs did not pose significant cancer risks to the residents.     

某垃圾焚烧厂投产前后周边土壤二英类化合物的分布

为研究垃圾焚烧厂运行对周边土壤二英类化合物（PCDD/Fs）含量的影响,采集了珠三角地区某垃圾焚烧厂投产前和投产后周边土壤样品,分析研究了该垃圾焚烧厂运行对周边土壤中PCDD/Fs含量和组分的变化.结果表明:①2012年（投产前）珠三角地区某垃圾焚烧厂周边土壤PCDD/Fs含量较低,范围为163~591 ng/kg（毒性当量范围为0.198~0.863 ng I-TEQ/kg,I-TEQ为国际毒性当量因子折算的毒性当量值）;2017—2019年（投产后）周边土壤PCDD/Fs含量范围为151~1.75×103 ng/kg（毒性当量范围为0.812~3.88 ng I-TEQ/kg）,与其他研究相比处于较低的水平.②投产后,距该垃圾焚烧厂较近（1.5 km）的采样点（S1）土壤PCDD/Fs含量逐年增长,在较远（5.2 km）但人口较密集的采样点（S3）土壤PCDD/Fs含量整体较高,但呈逐年下降趋势.③投产后,土壤中的17种PCDD/Fs单体组分中,毒性当量贡献率最高的单体为八氯二苯并二英（OCDD）和2,3,4,7,8-五氯二苯并呋喃（2,3,4,7,8-PeCDF）,二者毒性当量贡献率范围为15.7%~45.4%.④在同一采样点土壤PCDD/Fs单体组分年间差异不明显,但同一年份不同采样点差异明显.研究显示,目前该垃圾焚烧厂周边土壤PCDD/Fs含量较低,但仍需要长期监测其可能带来的风险.