基于降水等级分异方法的低影响开发小区雨水径流污染负荷削减率的评估

为定量评估低影响开发(LID)技术对雨水径流污染负荷的削减率,选取嘉兴市柳岸禾丰小区作为LID小区,与其临近且下垫面类型相似的浅水湾小区作为传统小区,同步监测小区的外排水量和TP浓度,根据降水等级分异计算2个小区同等降水情景下单位面积污染负荷量,再以传统小区的单位面积污染负荷量为基准核算LID小区的雨水径流污染负荷削减率。结果表明：小雨时,LID设施可消纳其服务范围内的所有径流及所携带的污染物,污染负荷削减率达100%;当降水量增至超过LID设施功能阈值时,污染物削减率开始降低,中雨时降至67%,大雨时降至46%,年均雨水径流污染负荷削减率约为66%。整体来看,LID设施雨水径流污染负荷削减率表现出明显的降水等级差异。采用降水等级分异的方法能够减少降水等级所造成的误差,确保评估结果的精准程度,为小区LID设施建设提供可靠的决策依据。

     

碱片—离子色谱法测定大气中硫酸盐化速率方法探讨

实验证实碱片－离子色谱测定大气中硫酸盐化速率方法操作简便快速，准确可靠，最低检出浓度可达０．１ｍｇ／Ｌ，可替代碱片－重量法测定。     

混合菌对石油的降解

从含油污水中分离得到4株能高效降解石油的微生物菌株(X2、X3、X4、X5),经鉴定,4株菌分别属于黄单胞菌属(Xanthomonas sp.)、动胶菌属(Zoogloea sp.)、芽孢杆菌属(Bacillus sp.)和邻单胞菌属(Plesiomonas sp.).通过观察4株菌在原油培养基中的生长变化过程,确定了其中的优势菌;并对4株菌进行复配实验以确定各株菌混合后的石油降解效果;用正交实验法确定达到最佳石油降解效果各菌的投加量;通过对残油的Gc-MS测定分析,确定各菌在降解石油时所起的作用.结果表明,混合菌株中菌X4为优势菌,且有高的降解效果(达68,60％),其它3株降解率不高的菌混合投加也能达到较高的降解效果(达63.17％),菌X4是混合菌株维持高降解率的关键;达到最佳降解效果的各菌投加量分别为0.1％、0.1％、0.5％、2.0％;菌X2和菌X3降解C12-C16直链烃和少量支链烃,菌X4和菌X5对C12-C22直链烃有好的降解效果.图2表4参10     

Potassium carbonate-based ternary transition temperature mixture (deep eutectic analogues) for CO2 absorption: Characterizations and DFT analysis

•Addition of hindered amine increased thermal stability and viscosity of TTTM. •Addition of hindered amine improved the CO₂ absorption performance of TTTM. •Good the CO₂ absorption of recycled solvents after two regenerations. •Important role of amine group in CO₂ absorption of TTTM confirmed by DFT analysis. Is it possible to improve CO₂ solubility in potassium carbonate (K₂CO₃)-based transition temperature mixtures (TTMs)? To assess this possibility, a ternary transition-temperature mixture (TTTM) was prepared by using a hindered amine, 2-amino-2-methyl-1,3-propanediol (AMPD). Fourier transform infrared spectroscopy (FT-IR) was employed to detect the functional groups including hydroxyl, amine, carbonate ion, and aliphatic functional groups in the prepared solvents. From thermogravimetric analysis (TGA), it was found that the addition of AMPD to the binary mixture can increase the thermal stability of TTTM. The viscosity findings showed that TTTM has a higher viscosity than TTM while their difference was decreased by increasing temperature. In addition, Eyring’s absolute rate theory was used to compute the activation parameters (ΔG*, ΔH*, and ΔS*). The CO₂ solubility in liquids was measured at a temperature of 303.15 K and pressures up to 1.8 MPa. The results disclosed that the CO₂ solubility of TTTM was improved by the addition of AMPD. At the pressure of about 1.8 MPa, the CO₂ mole fractions of TTM and TTTM were 0.1697 and 0.2022, respectively. To confirm the experimental data, density functional theory (DFT) was employed. From the DFT analysis, it was found that the TTTM+ CO₂ system has higher interaction energy (|ΔE |) than the TTM+ CO₂ system indicating the higher CO₂ affinity of the former system. This study might help scientists to better understand and to improve CO₂ solubility in these types of solvents by choosing a suitable amine as HBD and finding the best combination of HBA and HBD.     

石家庄某制药企业污水处理过程中NH3排放研究

为了解污水处理过程中各处理单元NH₃的排放特征,采集石家庄某制药企业各污水处理单元以及经过废气治理后排放的样品,计算各采样点NH₃浓度及排放量。结果表明:各污水处理单元中,水解酸化池NH₃浓度和单位体积污水NH₃排放量均为最高,分别为62.89和3 360 mg∕m ³。各污水处理单元NH₃总排放量为0.97 kg∕h,单位体积污水NH₃排放量为9 312 mg∕m ³;经废气治理后,排入环境的NH₃为0.25 kg∕h,单位体积污水NH₃排放量为2 400 mg∕m ³,去除率为74.2%,经治理后NH₃排放量明显降低。南区、北区废气治理采用碱洗+氧化+水洗工艺,NH₃去除率分别为93.3%和83.1%;生物区废气治理采用生物滴滤床工艺,NH₃去除率为39.1%,碱洗+氧化+水洗工艺对NH₃的去除效果好于生物滴滤床工艺。     

响应面法分析Fenton氧化处理采油废水的过程

采用Fenton氧化对采油废水进行研究,选取双氧水与二价铁离子的摩尔比、初始pH值和反应时间为自变量,以废水的COD去除率为响应值,通过Box-Behnken设计方法进行实验设计,进行了3因素3水平共15个实验点的实验。使用响应面分析法对实验结果进行模拟及分析,建立了响应值与3个自变量的二次多项式方程模型。Fenton氧化的优化工艺条件:n(H2O2):n(Fe2+)=0.8,pH=3.0以及反应时间60 min。在该优化条件下,废水的COD去除率可达72.8%,经实验验证,实际值与模型预测值拟合性好,偏差仅为0.5%。实验结果证实了该模型分析采油废水处理运行参数的准确性。优化工艺后的处理水质COD值完全满足油田废水达标排放的要求。通过总离子色谱图和质谱检索分析原油中的成分变化情况,证实Fenton方法对原油组分的降解效果。     

生活垃圾堆肥工艺条件及其反应动力学研究

为了改善堆肥微环境 ,提高生活垃圾堆肥速率 ,研究堆肥工艺条件及其反应动力学是非常必要的。通过控制堆肥工艺条件 ,如初始温度、含水率、C/N比及堆料颗粒大小 ,研究生活垃圾堆肥过程中生物、化学及物理因素的变化。试验结果表明 ,生活垃圾堆肥反应符合一级反应动力学 ;合理控制堆肥初始反应条件 ,能明显提高堆肥效率。     

Key features of new particle formation events at background sites in China and their influence on cloud condensation nuclei

New particle formation (NPF) event at multi rural sites in China Identifying the characteristics of NPF event Comparing NPF event between clean and polluted conditions Quantifying contribution to the cloud condensation nuclei Implication of climate and air quality Long-term continuous measurements of particle number size distributions with mobility diameter sizes ranging from 3 to 800 nm were performed to study new particle formation (NPF) events at Shangdianzi (SDZ), Mt. Tai (TS), and Lin’an (LAN) stations representing the background atmospheric conditions in the North China Plain (NCP), Central East China (CEC), and Yangtze River Delta (YRD) regions, respectively. The mean formation rate of 3-nm particles was 6.3, 3.7, and 5.8 cm⁻³·s⁻¹, and the mean particle growth rate was 3.6, 6.0, and 6.2 nm·h⁻¹ at SDZ, TS, and LAN, respectively. The NPF event characteristics at the three sites indicate that there may be a stronger source of low volatile vapors and higher condensational sink of pre-existing particles in the YRD region. The formation rate of NPF events at these sites, as well as the condensation sink, is approximately 10 times higher than some results reported at rural/urban sites in western countries. However, the growth rates appear to be 1–2 times higher. Approximately 12%–17% of all NPF events with nucleated particles grow to a climate-relevant size (>50 nm). These kinds of NPF events were normally observed with higher growth rate than the other NPF cases. Generally, the cloud condensation nuclei (CCN) number concentration can be enhanced by approximately a factor of 2–6 on these event days. The mean value of the enhancement factor is lowest at LAN (2–3) and highest at SDZ (~4). NPF events have also been found to have greater impact on CCN production in China at the regional scale than in the other background sites worldwide.     

香港城市固体废物系统管理

本文以大量翔实的数据介绍了香港对城市固体废物的系统管理,即分类、收集、监测分析、处理和预测评价。香港环保署自８０ 年代开始对城市固体废物进行监测并系统管理。在全港设置了３ 个大型策略性填埋场、５ 个垃圾转运站、１ 个垃圾焚烧厂（１９９７ 年５ 月关闭） 和１个化学废物处理中心。目前,香港政府正筹建一个新的、技术先进的焚烧厂。从１９８６ ～１９９７年,这些废物处理设施处理全港废物量为８９６０ ～２４３００ｔ／ｄ,其中城市固体废物比例每年不等,最低为３０ ．７ ％ ,最高为６５ ．５ ％ 。１９９７ 年,这些废物中可循环再利用物接近５０ ％ ,出口部分达１２０ 多万吨,回收资金２０ 多亿港元。根据历年来城市固体废物量与本地生产总值（ＧＤＰ）和人口数量的密切相关性,预测出２０１１ 年城市固体废物人均产率为２ ．５６ｋｇ／ 人·ｄ, 城市固体废物量为１２８１０ ｔ／ｄ。城市固体废物系统管理紧迫而重要,香港的经验是值得我们借鉴的。     

基于煤矸石制备的聚合氯化铝铁钛及其在二沉池出水处理中的应用

以煤矸石酸浸液为原料,经过钛掺杂、聚合、熟化和浓缩干燥等过程,制备了高效无机高分子混凝剂聚合氯化铝铁钛(PTAFC)。分别考察了钛投加量、pH、聚合温度、聚合时间对PTAFC混凝性能的影响,同时研究了PTAFC对城镇污水处理厂二沉池出水浊度、COD、总磷和氨氮的去除效果,并与聚合氯化铝铁(PAFC)进行了对比。结果表明：在钛铁摩尔比0.3、pH=1.5、聚合温度60 ℃、聚合时间3 h、常温熟化24 h时,所制得的PTAFC性能最佳;在投加量70 mg·L⁻¹、pH=7、反应温度20 ℃、慢速搅拌速度40 r·min⁻¹的混凝条件下,对自配水的浊度、COD和UV₂₅₄的去除效果最好,去除率分别为99.13%、37.25%和39.9%。PTAFC对城镇污水处理厂二沉池出水的浊度和总磷有极好的去除效果,同时对COD和氨氮有一定去除能力,污染物去除能力明显优于PAFC。上述研究成果对有效减少煤矸石的堆存量、拓宽煤矸石利用渠道,实现混凝剂的低成本、高效率工业化生产和应用具有重要的意义。