高压脉冲液相放电废水处理技术的研究进展

综述了国内外高压脉冲液相放电技术在水处理方面的应用及研究现状,概述了高压脉冲液相放电技术的原理以及目前高压脉冲液相放电技术的主要研究方向,如高压脉冲电源、物理效应、反应器、污染物和降解机理等方面,并提出了此技术存在的问题和前景.     

液膜分离技术处理含Cr6+废水的研究

采用液膜分离技术处理Cr^6＋质量浓度为200—1000mg／L的废水,考察了膜溶剂、载体、内水相、外水相、pH、乳水比（乳液与废水的体积比）等因素对处理效果的影响,通过正交实验得出最佳实验条件。结果表明,在膜溶剂为煤油、载体为三辛胺、内水相为氯氧化钠、氢氧化钠质量分数为2％、pn为1、乳水比为1：4的最佳条件下,Cr^6＋的去除率可达98．4％。     

Performance of a novel vertical-flow settler: a comparative study

By increasing particle concentration and G value （root-mean-square velocity gradient） to enhance flocculation, a novel vertical-flow settler was designed to increase sedimentation effectiveness, and to simultaneously improve operational stabilization. Due to the gradual decrease in upward flow-rate of raw water, a floes blanket would form and suspend in the middle section of the settler, not at the bottom as in a conventional clarifier. Enough large floes, resulted from flocculation or fltration, would continuously settle out of the floes blanket, and simultaneously, the floes in raw water or those forming above the blanket would ceaselessly enter the floes blanket. As a result, the floes concentration in the blanket could keep a dynamic balance. The hydrodynamic shear in the blanket was improved by flow separation, which was induced by the abrupt change in flow channel. Due to the floes blanket and improved hydrodynamic shear, flocculation would be enhanced, which was helpful for removing fine particles in raw water. A comparative study showed that the novel vertical-flow settler had a much better performance in the removal of the particles in raw water than a conventional one, when they treated kaolin suspensions of different concentrations （500, 100 and 50 mg/L, respectively） coagulated by polyaluminum chloride（PAC1） at the up-flow rates of 1 and 2 mm/s, respectively.     

Pyrolysis of rice husk and sawdust for liquid fuel

The paper is focused on studying how to convert rice husk and sawdust into liquid fuel. Rice husk, sawdust and their mixture were pyrolyzed at the temperature between 420℃ and 540℃, and the main product of liquid fuel was obtained. The experimental result showed that the yield of liquid fuel heavily depended on the kind of feedstock and pyrolysis temperature. In the experiments, the maximum liquid yields for rice husk, sawdust and their mixture were 56% at 465 ℃, 61% at 490℃ and 60% at 475℃ respectively. Analysis with GC-MS and other apparatus indicated that the liquid fuel is a complicated organic compound with low caloric value and can be directly used as fuel oil without any up-grading. As a crude oil, the liquid fuel can be refined to be vehicle oil.     

NH3-N在大连湾的水环境行为模拟研究

应用三维水质模型对大连湾中的主要污染物NH3-N的行为进行了模拟,对NH3-N浓度的时空变化规律以及其影响因素进行了研究,选择主要的模型参数进行了灵敏度分析。由空间分布的模拟结果可知,在大连湾,NH3-N浓度主要集中在排污口附近区域,灵敏度分析显示,在排污口区水体的扩散能力对NH3-N浓度的影响较大。由季节变化模拟结果可知,在湾顶部的排污口区NH3-N浓度显示明显的季节变化趋势。在湾中部和朝海边界的湾口区NH3-N浓度较低,变化平缓。模拟结果可以为大连湾的污染控制、水质规划和管理提供科学依据。     

苦味酸测定中关键问题的研究

目前测定苦味酸的国标方法为《生活饮用水标准检验方法有机物指标》(GB/T 5750.8—2006)中的衍生物-液液萃取-气相色谱法,在实际测试过程中,发现水样pH值和基质效应会影响苦味酸测定。当pH值为8~12时,生成的氯化苦响应强度变化不大;在pH约为13时,响应强度最大。水质中除腐殖酸、硝基甲烷及2,4,6-三硝基甲苯会影响苦味酸测定外,硝基酚类和甲基酚类同样起到正干扰作用,因此,国标方法不能全面和准确地测定水中的苦味酸含量。     

基于疲劳累积破坏机制的储罐结构动力可靠度分析

针对随机风载荷作用下储罐结构动力可靠性问题,以300 m3的中小型立式低温储罐为研究对象,利用AR模型进行数值模拟得到风载荷的脉动风速时程与脉动功率谱密度函数。采用ANSYS建立储罐三维有限元模型,并对储罐进行动力学分析,计算出储罐结构的随机响应,进而求出随机风载荷作用下储罐结构动力可靠性所需全部数字特征,最后利用疲劳累积损伤机制计算得到储罐的动力可靠度。结果表明:假设结构强度不随时间退化,前5 a动力可靠度基本保持不变,随着使用年限的延长,动力可靠度下降速度明显增大。研究方法可为储罐的动力可靠性及寿命预测提供一定的理论依据。     

Morphological characteristics of flashing jet throughout superheated liquid release

Many release problems involve two-phase releases of hazardous materials of superheated liquids with high energy into the atmosphere. Such accidents are accompanied by violent phase transition and form catastrophic flashing jets. In this work, experimental and theoretical analyses were conducted to investigate dynamic characteristics of flashing jet morphology and their dependence on pressure-decay dynamics under different storage pressures, superheats, and nozzle diameters. Flashing jet morphology and angle throughout two-phase releases were captured by a high-speed camera, and the corresponding source pressure in the superheated liquid tank was measured simultaneously. Results show that three typical phases, expansion, stabilization, and decay, are characterized throughout two-phase release based on the evolution of flashing jet morphology. The jet initially expands gradually due to the enhancement of phase transition intensity, and then keeps stable when the intensity reaches its maximum, and terminally decays rapidly due to the depletion of superheated liquid. Phase transition intensity at the nozzle exit is mainly controlled by the pressure-decay dynamics. Bubbles nucleation inception sites gradually move upstream of the nozzle during the pressure decay process increasing the phase transition intensity. The increase of storage pressure, superheat and nozzle diameter promotes the mechanical and thermodynamic effects on the jet breakup. The significant increase of mechanical and thermodynamic effects effectively accelerates droplets evaporation and further affects flashing jet morphology.     

Experimental investigation of the lower flammability limit of volatile liquid fuel-aluminum powder mixtures in air

Aluminum powder was always chosen as an additive to improve the explosive performance. In this work, experiments were performed to investigate the lower flammability limit (LFL) of volatile liquid fuel-aluminum powder mixtures using a 20 L closed spherical stainless steel vessel at a temperature of 20 °C (293 K) and 40 °C (313 K). The volatile liquid fuels tested in the work were diethyl ether (DEE), epoxypropane (PO), n-pentane and n-hexane. DEE, PO and n-pentane are in the liquid phase at room temperature and can easily transition to the gas phase at 40 °C (313 K). Through a series of experiments carried out, it was found that the change in phase would affect the interaction between the components. Aluminum powder always has an inhibitory effect on the flammability of the mixtures when it is mixed with gas-phase fuels. The inhibition effect was most obvious when the aluminum powder concentration reached 200 g/m³. While the interaction between aluminum powder and liquid-phase volatile fuels was promotion and was influenced by the component proportion and the type of the volatile fuels.     

Study on the dynamic response of polyurea coated steel tank subjected to blast loadings

Steel tanks are widely used in the storage of various chemical liquids, and the blast resistance of the tanks is very important because of the explosiveness of these liquids. To explore a feasible method to improve the blast resistance of steel tanks, the effect of polyurea coating on the blast resistance of steel storage tank is investigated in this paper. The responses of monolithic steel tanks and polyurea coated tanks under blast loads are studied by field blast experiments using TNT explosive, and the results shows that the polyurea layers are effective in reducing the maximum and residual displacements of the tank. Numerical simulations are performed and validated, and the deformation process and stress and strain distribution of the tanks are analyzed accordingly. The increase on the bending moment of the plastic hinge lines of the tanks and the increase of the area density of the cylindrical shell induced by the polyurea layers are believed to be the two main factors contributing to the displacement reduction effect of polyurea in this paper. The validated numerical model is used to study the influence of polyurea layer's thickness on the deflection of the tank, and a nearly inversely proportional relationship between the thickness and the maximum displacement is found. Three deformation modes of the tanks are identified when subjected to blast load with varying intensity and it is found that the displacement reduction effect of polyurea varies in different deformation modes.