Evaluation of mercury speciation and removal through air pollution control devices of a 190 MW boiler

Air pollution control devices (APCDs) are installed at coal-fired power plants for air pollutant regulation. Selective catalytic reduction (SCR) and wet flue gas desulfurization (FGD) systems have the co-benefits of air pollutant and mercury removal. Configuration and operational conditions of APCDs and mercury speciation a ect mercury removal e ciently at coal-fired utilities. The Ontario Hydro Method (OHM) recommended by the U.S. Environmental Protection Agency (EPA) was used to determine mercury speciation simultaneously at five sampling locations through SCR-ESP-FGD at a 190 MW unit. Chlorine in coal had been suggested as a factor a ecting the mercury speciation in flue gas; and low-chlorine coal was purported to produce less oxidized mercury (Hg2+) and more elemental mercury (Hg0) at the SCR inlet compared to higher chlorine coal. SCR could oxidize elemental mercury into oxidized mercury when SCR was in service, and oxidation e ciency reached 71.0%. Therefore, oxidized mercury removal e ciency was enhanced through a wet FGD system. In the non-ozone season, about 89.5%–96.8% of oxidized mercury was controlled, but only 54.9%–68.8% of the total mercury was captured through wet FGD. Oxidized mercury removal e ciency was 95.9%–98.0%, and there was a big di erence in the total mercury removal e ciencies from 78.0% to 90.2% in the ozone season. Mercury mass balance was evaluated to validate reliability of OHM testing data, and the ratio of mercury input in the coal to mercury output at the stack was from 0.84 to 1.08.     

声激励锚杆轴力监测传感器的研制

根据现有的锚杆支护方式,提出一种采用声激励来监测锚杆轴力的新方法,该方法属于无损检测。阐述了锚杆轴力监测传感器的基本原理,介绍了传感器的构造及参数的设置,从强度、模态、声学3个方面进行了详细说明,分析了共振板的厚度变化对声学性能的影响。结果表明,该传感器满足设计要求,方法可行、有效。     

Seat strength in rear body block tests

Purpose: This study collected and analyzed available testing of motor vehicle seat strength in rearward loading by a body block simulating the torso of an occupant. The data were grouped by single recliner, dual recliner, and all belts to seat (ABTS) seats.

Methods: The strength of seats to rearward loading has been evaluated with body block testing from 1964 to 2008. The database of available tests includes 217 single recliner, 65 dual recliner, and 18 ABTS seats. The trends in seat strength were determined by linear regression and differences between seat types were evaluated by Student's t-test. The average peak moment and force supported by the seat was determined by decade of vehicle model year (MY).

Results: Single recliner seats were used in motor vehicles in the 1960s to 1970s. The average strength was 918 ± 224 Nm (n = 26) in the 1960s and 1,069 ± 293 Nm (n = 65) in the 1980s. There has been a gradual increase in strength over time. Dual recliner seats started to phase into vehicles in the late 1980s. By the 2000s, the average strength of single recliner seats increased to 1,501 ± 335 Nm (n = 14) and dual recliner seats to 2,302 ± 699 Nm (n = 26). Dual recliner seats are significantly stronger than single recliner seats for each decade of comparison (P < .001). The average strength of ABTS seats was 4,395 ± 1,185 in-lb for 1989–2004 MY seats (n = 18). ABTS seats are significantly stronger than single or dual recliner seats (P < .001). The trend in ABTS strength is decreasing with time and converging toward that of dual recliner seats.

Conclusions: Body block testing is an quantitative means of evaluating the strength of seats for occupant loading in rear impacts. There has been an increase in conventional seat strength over the past 50 years. By the 2000s, most seats are 1,700–3,400 Nm moment strength. However, the safety of a seat is more complex than its strength and depends on many other factors.     

航空发动机涡轮叶片热障涂层冲蚀试验装置的研制

目的通过研制热障涂层冲蚀服役环境的模拟装置,来研究冲蚀失效机制。方法通过研制模拟热障涂层高温热冲击的燃气喷枪,在喷枪中设计速度、流量可控的颗粒送料系统,同时在装置中集成裂纹演化实时检测的声发射系统。结果该系统实现了热障涂层冲蚀服役环境的模拟,温度场、裂纹演化损伤参量的同步采集、输出与显示,从而完成了冲蚀服役环境模拟与关键损伤参量实时检测的一体化设计。结论装置能完成热障涂层常温、高温等各种服役温度、各种冲蚀角度、各种冲蚀速度等条件下的模拟试验,并提供较为系统的损伤参量检测数据,为理解热障涂层的冲蚀机理、优化其设计制备提供有效的试验数据。     

儿童在道路行驶中的安全与防护——加拿大新的儿童汽车座椅法规与测试方法

本文主要介绍加拿大新的《机动车辆约束系统和加高座椅安全法规》（SOR/2011-16）的相关内容,同时对儿童汽车座椅的研究与测试方法也进行了详细描述,以对我国相关行业提供借鉴。     

电气设备触电危险因素分析

我国现阶段生产、生活中触电事故增加,采用故障树的分析方法,对用电设备触电事故进行危险因素分析,得出保护接地在供配电系统中的重要作用。简要介绍保护接地,并指出目前我国用电设备保护接地中存在的问题及接地故障的防范措施。     

矿井通风网络数据可靠性检验

进行矿井通风阻力测定时,由于受环境的温度、湿度、压力传递存在时间差以及测点处标高不准确等因素的影响,根据实测数据,计算所得矿井巷道基础数据存在一定的误差,常用的测量数据检验方法只能对若干条通路进行闭合回路检验,而不能对全矿井通风网络基础参数进行可靠性检验。本文中所介绍的检验方法将风网基础数据输入通风网络解算软件,以实测风量和经过计算所得巷道风阻为基准,实测风量为目标条件,进行计算机通风网络模拟,对全矿井巷道风阻进行连续的优化调整,使通风网络模拟结果与实际测定各巷道风量基本符合,从而实现全矿井风网基础数据的可靠性检验。该方法在某矿进行了实际应用,实践证明此方法科学、准确的获得了全矿巷道风阻参数,为矿井的通风改造奠定了技术基础。     

快速分析技术在煤质检测中的应用及发展

煤质检测关系到电站燃煤锅炉的稳定安全运行.综述了几种快速分析技术在煤质检测中的应用及原理,并对今后我国在该技术领域的发展提出了建议.     

钢筋混凝土箱型高墩双向拟静力试验研究

随着高墩大跨桥梁的广泛应用,其抗震问题也越来越突出。本文主要考虑轴压比、长细比的影响,进行了6个钢筋混凝土薄壁箱型高墩缩尺模型的双向拟静力试验,以及反复荷载作用下的非线性分析。研究表明:①钢筋混凝土薄壁箱型高墩柱在多维荷载共同作用下,主要发生典型的弯曲破坏,但剪切作用也不容忽视;②墩柱的破坏受到不同方向耦合作用的显著影响,尤其是抗弯刚度小的一侧受到的影响更大,较早就出现开裂,提前进入塑性发展阶段;③非线性有限元计算的滞回曲线、骨架曲线等与试验结果基本吻合;④建立了考虑轴压比、长细比影响的钢筋混凝土薄壁箱型高墩的双向荷载—位移恢复力模型,该模型基本能够反映钢筋混凝土薄壁箱型高墩的抗震性能,可供钢筋混凝土箱型高墩柱及高墩桥梁结构的抗震设计和动力计算参考。     

可变径管道漏磁检测有限元仿真与实验研究

为了更好地支持压力管道检验,降低事故率,本文基于漏磁检测原理,利用有限元分析软件建立了管道外漏磁检测模型,对管道漏磁检测进行了仿真计算,得到了缺陷处漏磁场特征曲线,模拟了圆柱形缺陷对管道外壁漏磁场的影响,得出了不同参数缺陷对漏磁场的影响规律,并且基于理论和有限元计算结果试制了可变径管道外漏磁检测仪的样机,利用该检测仪对壁厚为8mm的带有人工缺陷的管道进行扫描检测,研究不同参数缺陷对漏磁场信号的影响规律。结果表明,所得结果与有限元仿真的结果吻合良好,且缺陷检测精度及效果满足要求,另外,检测装置对内外壁缺陷检测同样可行有效,适合特种设备（压力管道）检测的工程应用。