城镇餐饮泔水离心脱水试验研究

简要介绍了城市餐饮泔水的来源、基本特征及目前主要处理技术方法,提出了餐饮泔水无害资源化新工艺。对提出的工艺中泔水离心脱水工序进行了试验研究,并得出最佳离心参数:时间5min、转速3200rmin。     

肉类加工废水生物脱氮工艺的工程应用

采用ABRSBR组合工艺开展了大量现场模拟试验及动力学理论研究,最终获得了进一步提高肉类加工废水脱氮效率的措施途径。通过对已建成、正调试、正设计3种情况下肉类加工废水脱氮工艺的研究,表明此脱氮工艺具有良好的工程应用价值。     

超滤处理洗涤污水循环利用的中试研究

采用不同材质国产超滤膜聚丙烯（PP）、聚丙烯腈（PAN）和聚砜（PS）,进行了洗涤污水处理循环利用的现场中试研究.结合超滤工艺出水水质和膜污染分析,3种膜材质中PAN膜较优,有效去除了水中浊度、悬浮物、油脂等污染物,一定程度保留了游离阴离子表面活性剂（LAS）,长期循环洗涤对衣物的白度无不良影响.根据相关性分析,超滤出水较高COD值很大程度上是由水中LAS引起的.超滤膜对细菌、大肠菌群的去除率较低,出水通过紫外消毒,当紫外线密度≥3?750 J/m²时,微生物水平能够达到国家饮用水水质标准.根据不同水力反冲洗条件下膜渗透通量和净产水量比较,PAN膜最佳水力反冲洗条件为0.5 h反冲洗2 min.长期运行时超滤膜化学清洗方法采用碱洗法方便有效.     

Treated wastewater irrigation effect on soil, crop and environment： Wastewater recycling in the loess area of China

A study was carried out at the Loess Plateau in Dongzhi,China,to test the feasibility of using secondary treatment sewage effluent and to determine whether the water quality would then meet the recommended irrigation norm.Seven crops,including celery,wheat, maize,millet,apples,rapeseed and yellow beans,were tested in the study.Physical and chemical properties of the soil,crop yield and quality and leachate at different soil depths were measured.In most cases,the quality of the crops that made use of treated sewage was not distinctively different from those that did not use treated sewage.However,yields for the former were much higher than they were for the latter.Leachates at different soil depths were analyzed and the results did not show alarming levels of constituents.For a period of approximately 14 months,the treated sewage irrigation had no significant effect on the loess soil and no cases of illness resulting from contact with the treated sewage were reported.With treated sewage irrigation,a slight increase in the organic content of the soil was observed.     

大型水利水电工程实施占用耕地补偿制度的思考

本文在分析长江三峡工程用地特点的基础上。对大型水利水电工程实施耕地补偿制度中的问题和困难进行调查研究，认为应从新的视角来认识大型水利水电工程的耕地占补平衡问题。进而探索耕地补偿制度实施的新途径和新方式。应在耕地总量动态平衡政策适当调整的基础上．将“以地补地”和“缴费补地”的方式相结合。既通过土地整理．在提商土地质量的前提下增加耕地的有效面积：又要落实耕地开垦费．扶持库区的土地整理。从而使库区的耕地占补制度顺利实施。     

红壤稻田系统有机物循环再利用潜力及增产作用

10年田间试验结果表明：红墩妥田系统有机养分循环再利用潜力大，水稻收获，年均从稻田系统中输出NPK的总量最大可达到224.7,53.0和271.4kg/hm^2，有机物循环再利用，年均可归N，P，K量最大分别为115.1,35.8和231.5kg/hm^2，占系统输总量的51.2%,67.5%g和85.3%，保持稻田系统内有机物循环再利用可提高系统生产力，在不施化肥的情况下，增产3056kg/hm^2，增施N肥，增产2753kg/hm^2，增施N，P肥，增产1543kg/hm^2；NPK配合，增产984kg/hm^2；有机物循环再利用还可增强稻田系统的稳产性能，降低稻谷产量的年际变异系数；有机物循环再利用对水稻的增产有着明显的残效叠加作用，在施用N，P，K化肥基础上圾机物养分循环再利用水稻增产率在试验期间的前5年为7．2％，后5年平均为9．4％。     

乡镇垃圾分类循环利用现状——以闽侯县上街镇为例

由于我国乡镇经济的迅速发展以及乡镇村民生活水平加速提高,乡镇的垃圾种类及数量趋向于城市.乡镇村民居住较为分散,垃圾分类、收集、循环利用相较于城市困难,因此推进乡镇垃圾分类循环利用迫在眉睫.本文从闽侯县上街镇展开调查,以乡镇垃圾分类、回收循环利用为关键词展开分析,并从上街镇垃圾分类循环利用模式存在的问题进行分析、总结和建...     

加快推进重大政策和重大项目落地,确保生态环境质量总体改善——《“十三五”生态环境保护规划》解读

当前我国环境形势仍十分严峻,"十三五"期间要实现生态环境质量总体改善,需要"硬制度""硬项目"和"硬投入"。文章结合《"十三五"生态环境保护规划》,对其中的重大改革制度政策创新和重大工程项目安排以及资金投入渠道等进行了深入分析解读,提出为确保生态环境质量总体改善,必须积极推动重大改革政策的实施,加快推进重大项目的落地,加大环保资金的投入,优化环保资金渠道。     

基于LCA的废旧资源循环利用节能减排效果评估模式与方法研究——以吉林省某钢铁企业为例

促进废旧资源循环利用是加快推进我国生态文明建设,完成节能减排目标的必然选择。本文基于生命周期评价模式,从微观企业层面入手,构建产品全生命周期基准流程,引入能量输入与环境输出参数,建立废旧资源循环利用节能减排效果量化核算模型,评估再生产品的节能减排经济成效,并以吉林省某钢铁企业为例,评估"废钢-电炉"短流程和"铁矿石-高炉-转炉"长流程的能源、环境、成本差异,辨识影响废钢再循环节能减排效果的主要因素和重要环节。结果显示,再生钢铁全生命周期与原生钢铁全生命周期相比,节能588.48kgce/t,节能率为84%;主要污染物中SO2减排率最高,达92%;CO2总减排1 180.92 kg/t,减排率为67%;总成本却高出198元/t。其中,炼铁工序的节能量和减碳量最大,烧结工序SO2、NOx和烟(粉)尘减排量最大,焦化工序COD和氨氮减排量最大,回收、加工处理、炼钢环节节能量和减碳量以及SO2、NOx和烟(粉)尘减排量均为负。成本方面,再生钢铁生产成本高于原生钢铁308元/t,虽然再生钢铁由于污染减排可节省56元/t的排污费并获取54元/t的碳交易收益,但都不足以扭转电炉炼钢费用较高的现状。因此,国家应在电炉炼钢方面给予钢企及相关企业适当的财税扶持政策,在电价方面给予钢企一定的优惠或补贴,并完善废钢回收加工体系等,以促进废钢循环利用。基于LCA的废旧资源循环利用节能减排效果评估可以实现对产品生命周期全过程的资源、环境、成本的优化管理。     

An analysis of end-of-life terminology in the carbon fiber reinforced plastic industry

While many studies and reviews into the practices conducted by industry and academia to recycle and remanufacture carbon fibre-reinforced plastic (CFRP) exist, to date no investigation exists which regards the correctness of the use of the terms recycling and remanufacturing. As such, this paper seeks to analyse the CFRP reuse industry’s attempt to recycle and remanufacture manufacturing waste CFRP and end-of-life (EOL) CFRP with an emphasis on the terminology used to describe these practices. Firstly, this paper presents a justification of the importance of using EOL terminology correctly; outlining the benefits and problems associated with using the correct and incorrect terminology. This paper finds that in the case of CFRP remanufacturing, terminology is being applied incorrectly and in the case of CFRP recycling, particular care should be taken when applying the term recycled to CFRP or stating that CFRP has been recycled. Further, this paper proposes new terminology (in keeping with EU directives) which could be adopted by industry and academia working in this area. This paper also finds that in the case of remanufacture, CFRP is incapable of being remanufactured.